U-PROX SE KEYPAD

Universal reader with OSDP and keypad

U-PROX SE KEYPAD USER MANUAL

The U-PROX SE keypad is an adjustable universal SmartLine reader with a wireless keypad designed for mobile credentials and proximity identifiers. In conjunction with the U-PROX ID application and mobile identifiers, U-PROX IDs enable any access control system to utilize smartphones as access credentials.

Installation

1. Make a small recess or hole (diameter of 14 mm) to connect the cable under the reader's case.

2. Loosen the screw at the bottom of the reader.

3. Remove the top cover.

4. Carry out wiring to the control panel.

5. Mount the reader on the wall using the supplied plastic dowels and screws.

6. Place the top cover and tighten it with a screw.

Note: Installation on metal surfaces may decrease the reading range. Do not place readers closer than 20 cm from each other. It is possible to install two readers at a distance of 10-15 cm if their yellow wires (Hold/Sync) are interconnected. This synchronizes the readers to work alternately.

Connection

The reader offers seamless and easy connection to existing and new access systems due to its OSDP, Wiegand (26, 32, 34, 37, 40, 42, 56, 58, 64, 80 bits, with automatic selection), RS232, and TouchMemory support.

It is recommended to use a multi-core signal cable with a 0.22 mm² cross-section for each wire between the reader and the panel.

Wiegand

The reader connection wires functions are listed in the table below:

Function	English	Spanish	French	Portuguese	Ukrainian	Polish
+12V	+12V	+12V	+12V	+12V	+12V	+12V
GND	GND	Negro	Noir	Preto	Чорний	Czarny
Data0 (WDO)	Data0 (WDO)	Verde	Vert	Verde	Зелений	Zielony
Data1 (WD1)	Data1 (WD1)	Blanco	Blanc	Branco	Білий	Biały
Red LED (RD)	Red LED (RD)	Marrón	Brun	Marrom	Коричневий	Brązowy
Green LED (GN)	Green LED (GN)	Naranja	Orange	Laranja	Помаранчевий	Pomarańczowy
Beep	Beep	Azul	Bleu	Azul	Синій	Niebieski
Hold or sync	Hold or sync	Amarillo	Jaune	Amarelo	Жовтий	Żótty

It is recommended to use the following wiring when the reader is connected to the control panel with a twisted pair.

RS-232

The reader connection wires functions are listed in the table.

TouchMemory

The reader connection wires functions are listed in the table.

It is recommended to use the following wiring when the reader is connected to the control panel with a twisted pair.

Configuration

The reader can be fully configured, from indication to encryption modes, using the free mobile application U-Prox Config.

The reader is supplied without an engineering password for programming. To connect and set/reset the password, connect inputs D0 (green) and D1 (white) to each other and apply power to the reader.

The reader firmware can be updated using an NFC-enabled Android smartphone only.

Mobile Identification

The reader supports digital personal mobile credentials processed and stored in the user's smartphone via the U-PROX ID application. These can be transferred between the reader and the smartphone via NFC and/or 2.4 GHz radio.

The reader also supports hardware active mobile identifiers: U-PROX Tag and U-PROX Auto Tag.

The reader supports three operation modes for smartphones with U-Prox ID:

"Door-Proximity": 10-20 cm range. The reader activates via its built-in proximity sensor. Recommended for double-sided doors and turnstiles.
"Door": Up to 60-70 cm range.
"Barrier/Gate": Adjustable interaction range from 1 to 15 meters.

U-PROX ID application

The free mobile application U-PROX ID receives, stores, and transmits mobile credentials between the reader and the smartphone.

How to obtain mobile ID

Mobile IDs can be purchased from U-PROX dealers.

RFID, 125 kHz

The reader supports 125 kHz cards with amplitude (ASK - EmMarine, etc.) and frequency modulation (FSK - Temik, etc.). These cards are popular due to their low cost, but lack cloning protection.

Mifare® identifiers

The reader supports working with Mifare® cards, reading encrypted identifiers with a user-assigned card number, and using static or diversified encryption keys. Up to five encryption profiles can be used simultaneously.

Mifare® Classic

This is the least secure series of cards, with a vulnerability in the Crypto 1 (SL1) encryption algorithm. When using Mifare® Classic, it is recommended to encrypt all card sectors with a diversified encryption key.

Mifare® Plus

The reader supports SL1 and SL3 modes for Mifare® Plus. SL3 mode is recommended for its higher security and AES encryption algorithm.

The reader supports Mifare DESFire EV1, EV2, and EV3 cards, with AES encryption algorithm support.

Warranty

The warranty for U-PROX devices (excluding batteries) is valid for two years from the date of purchase. If the device operates incorrectly, please contact support@u-prox.systems first, as the issue may be resolvable remotely.

	U-PROX SL Steel Reader: Mobile Credentials & Access Control Guide Comprehensive guide to the U-PROX SL Steel reader, covering installation, connection options (Wiegand, RS232, TouchMemory), mobile identification, RFID/Mifare compatibility, configuration, and warranty information.
	U-PROX SL maxi SmartLine Reader Installation and Features Comprehensive guide to the U-PROX SL maxi SmartLine reader, covering its features, installation, connection options (Wiegand, RS-232, TouchMemory), mobile identification capabilities via the U-PROX ID app, and RFID/Mifare card support. Includes warranty information.
	U-PROX SE maxi: Universal SmartLine Reader for Mobile Credentials and Proximity Identifiers Detailed information on the U-PROX SE maxi, a universal SmartLine reader supporting mobile credentials, proximity identifiers, RFID, and Mifare cards. Includes installation, connection, configuration, and warranty details.
	U-PROX SL maxi SmartLine Reader Installation and Configuration Guide Comprehensive guide for installing and configuring the U-PROX SL maxi adjustable universal SmartLine reader for mobile credentials and proximity identifiers. Learn about connections, Wiegand and TouchMemory interfaces, mobile identification, and RFID/Mifare card support.
	U-PROX SE MINI User Manual: Universal Miniature Reader with OSDP Comprehensive user manual for the U-PROX SE MINI universal miniature reader. Covers installation, connection interfaces (OSDP, Wiegand, RS232, TouchMemory), configuration, mobile identification features, RFID compatibility (125 kHz, Mifare), and warranty information.
	U-PROX SmartLine SE Access Control Reader: Installation and Connection Guide Detailed guide for installing and connecting the U-PROX SmartLine SE access control reader. Covers setup, Wiegand, OSDP, RS-232, TouchMemory interfaces, mobile identification, and various identifier types (125 kHz, Mifare).
	U-PROX SmartLine SE Universal Reader with Keypad - Installation and Connection Guide Comprehensive guide for installing, connecting, and configuring the U-PROX SmartLine SE universal reader. Details wiring, interfaces (Wiegand, OSDP, RS-232, TouchMemory), mobile identification, and Mifare card support.
	U-PROX SE Keypad: SmartLine Reader Installation and Features Guide Comprehensive guide to the U-PROX SE keypad, a versatile SmartLine reader supporting mobile credentials, proximity identifiers, and various access control interfaces like OSDP and Wiegand. Includes installation, connection, configuration, and warranty information.