User Manual for CNC4PC models including: C48 -EXT_E-STOP and Probe Connector Board, C48, -EXT_E-STOP and Probe Connector Board, Probe Connector Board, Connector Board
USER'S MANUAL VER. 1 C48 EXTERNAL E-STOP AND PROBE Rev. 3.5 FEBRUARY 2022 USER'S MANUAL TABLE OF CONTENTS Contents Page # 1.0 OVERVIEW .....................................................................................................................1 2.0 FEATURES .....................................................................................................................1 3.0 BOARD DESCRIPTION ..................................................................................................2 4.0 CONNECTOR RJ45........................................................................................................3 5.0 PROBE JUMPER FOR RESISTOR ................................................................................3 6.0 JUMPER EXTERNAL E-STOP .......................................................................................4 7.0 JUMPER E-STOP ...........................................................................................................4 8.0 TERMINALS ...................................................................................................................5 8.1 Signal of Enable.........................................................................................................5 8.2 Signal EXT. E-STOP...................................................................................................5 8.3 E-STOP (Primary).......................................................................................................5 9.0 WIRING SAMPLE ...........................................................................................................6 9.1 Connection probe......................................................................................................6 9.2 Collision Detection connection with probe..............................................................7 9.3 Collision Detection connection and external E-stop with probe............................8 10.0 DIMENTIONS..................................................................................................................9 User's Manual Page i 1.0 OVERVIEW This board provides the interface to easily interconnect 1 Probe and 1 external E-Stop to CNC4PCbreakout board. 2.0 FEATURES · 1x 3.5mm jack connector for 1 Probe and Anti-Collision Feature New* · 1x 1/4" jack connector for 1 External E-Stop (Secondary- Optional E-Stop) · RJ45 and Terminal for all I/Os and Power lines · Easily mountable in the panel of CNC Control Boxes User's Manual Page 1 3.0 BOARD DESCRIPTION Requirements: It requires a power supply of 5 to 24VDC@200mA to operate. User's Manual Page 2 4.0 CONNECTOR RJ45 This connector allows an easy connection with C62, C76, or C82, boards. These RJ45 connectors are used not just to carry the INPUT/OUTPUT signals placed in terminals, but also to power board. RJ45 DESCRIPTION PIN GND 1 NOT USED 2 EXT. E-STOP/EN 3 PROBE 4 INDEX 5 EXT. E-STOP/EN 6 5V/24V 7 NOT USED 8 5.0 PROBE JUMPER FOR RESISTOR Set jumper in REQUIRED position if the input used in the breakout board to connect the probesignal is pulled to DOWN User's Manual Page 3 6.0 JUMPER EXTERNAL E-STOP If an External E-STOP (Secondary) is connected set jumper in USED position, if not set jumperin position NOT USED. 7.0 JUMPER E-STOP If used a power supply of 5VDC, set the two jumper as sample in the image If used a power supply of 24VDC and in the output of terminal de EN and EXT ESTOP wilwork with 24V, set jumper as sample in the image. User's Manual Page 4 8.0 TERMINALS 8.1 Signal of Enable Signal internally wired to the EXT. E-STOP signal. It can be used as an external enable for abreakout board. 8.2 Signal EXT. E-STOP This signal is the result of the series between E-STOP (Primary) and EXT. ESTOP (Secondary). 8.3 E-STOP (Primary) An E-STOP must be connected to those terminals in order to get any E-STOP signal in theEXT. E-STOP terminal. User's Manual Page 5 9.0 WIRING SAMPLE 9.1 Connection probe User's Manual Page 6 9.2 Collision Detection connection with probe User's Manual Page 7 9.3 Collision Detection connection and external E-stop with probe User's Manual Page 8 10.0 DIMENTIONS DISCLAIMER Use caution. CNC machines can be dangerous machines. Neither DUNCAN USA, LLC nor Arturo Duncan is liable for any accidents resulting from the improper use of these devices. This product is not a fail-safe device and it should not be used in life support systems or in other devices where its failure or possible erratic operation could cause property damage, bodily injury or loss of life. User's Manual Page 9Microsoft Word 2019