Honeywell UberHeat® 5 / UberHeat® Plus Heater

Contact Information

If you have any questions about the operation of this product, please contact us:

• 1-800-477-0457
• HoneywellPluggedIn.com/contact-us
• www.HoneywellPluggedIn.com

Important Safety Instructions

WARNING: READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS HEATER.

Failure to follow any of these safety instructions could result in fire, injury, or death.

Your Responsibilities: Electrical appliances may expose people to hazards that can cause severe injury as well as death. Use electrical products safely to avoid hazards.

General Precautions:

• Read all instructions before using this heater.
• Never leave an operating unit unattended.
• This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 feet (0.9m) from the front and sides of the heater.
• Extreme caution is necessary when any heater is used by or near children or those who are physically challenged.
• Always unplug the heater when not in use.
• Do not operate any heater with a damaged cord or plug, or if it malfunctions, has been dropped, or damaged in any manner. Discard the heater or return it to an authorized service facility for examination and/or repair.
• For residential use only.
• Do not use outdoors.
• Never locate the heater where it may fall into a bathtub or other water container.
• Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or appliances. Arrange the cord away from traffic areas and where it will not be a tripping hazard.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
• This heater draws 12.5 Amps during operation. To prevent overloading a circuit, do not plug the heater into a circuit that already has other appliances working.
• It is normal for the plug to feel warm to the touch; however, a loose fit between the AC outlet (receptacle) and plug may cause overheating and distortion of the plug. Contact a qualified electrician to replace loose or worn outlets.
• To disconnect the heater, first turn off the product, then grip the plug body and pull it from the wall outlet. Never pull by the cord.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as this may cause electric shock, fire, or damage to the heater.
• To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, or where openings may become blocked.
• A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
• Use this heater only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons.
• Always plug the heater directly into a wall outlet/receptacle. Do not use with an extension cord or relocatable power tap (outlet/power strip).
• Never tamper with this product or attempt to fix it. Any tampering with, or modification of this product can result in serious injury, death, or fire. Do not open. Risk of electric shock. There are no user serviceable parts inside.
• Do not remove product labels that contain warnings or safety instructions.
• The output of this heater may vary and its temperature may become intense enough to burn exposed skin. Use of this heater is not recommended for persons with reduced sensitivity to heat or an inability to react to avoid burns.
• Before cleaning, or storage, or when not in use, turn the product's controls to the OFF position and unplug the heater from the electrical outlet and allow to cool.
• Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9m) away from any combustible materials. Do not use on an unstable surface such as bedding or deep carpeting. Be sure the heater is not in a position where it may be a tripping hazard.
• If your home has aluminum wiring, have a licensed electrician check your receptacle's connections. When using a 1500 watt heater, aluminum wire connections can cause a safety issue.

SAVE THESE INSTRUCTIONS.

Set Up

Place the heater on a firm, level, open surface free from obstructions and at least 3 feet (0.9m) away from any wall or combustible material. Do not use on an unstable surface such as bedding or deep carpeting. Be sure the heater is not in a position where it may be a tripping hazard.

Moving the Heater

1. Turn off the heater.
2. Allow it to cool for ten minutes.
3. Unplug the heater and move it to the desired location. This heater is equipped with a Cool Touch Handle for your convenience.

Operation (HCE210 ONLY)

NOTE: Never leave an operating heater unattended.

All Purpose Heater Operation

With the Power Knob in the OFF position (◯), plug the heater into a polarized 120V outlet. Do not force the polarized plug into the outlet; it will only fit one way.

The Power Knob is equipped with two (2) settings: Low (SS) and High (SSS). The Low (SS) heat setting uses 900 Watts of power and the High (SSS) heat settings uses 1500 Watts of power. You can select the proper setting to accommodate your comfort level by turning the Power Knob to the desired heat setting. When you choose any setting, the red Power Light will come on. Because the Low (SS) heat setting does not require as much electricity to operate, it is more energy efficient.

Turn the Thermostat Control fully clockwise to the highest setting (0+). When the room reaches the desired temperature, slowly rotate the thermostat knob counter-clockwise until you hear a click. The thermostat is set at this room temperature.

When the room reaches the same temperature as the thermostat setting, the thermostat will make a clicking sound. At this setting, the thermostat will automatically turn the heater on and off to maintain the selected temperature.

To turn the unit off, turn the Power Knob counter-clockwise to the Power Icon (O) and the red power light is off. Unplug the heater when you are finished using it.

Operation (HCE220 ONLY)

NOTE: Never leave an operating heater unattended.

All Purpose Heater Operation

Plug the heater into a polarized 120V outlet. Do not force the polarized plug into the outlet; it will only fit one way.

Press the Power Icon (U) to turn the heater on. The red Power Light will come on. This heater is equipped with two (2) settings: Low (SS) and High (SSS). The Low (SS) heat setting uses 900 Watts of power and the High (SSS) uses 1500 Watts of power. You can select the proper setting to accommodate your comfort level with the Setting Button (< >). Because the Low (SS) heat setting does not require as much electricity to operate, it is more energy efficient.

The Adjustable Thermostat button (0) is equipped with 4 pre-set Heat Levels. To set the thermostat to one of these levels, press the Thermostat button (1) until the desired temperature is illuminated. The heater will operate at the High setting until the room reaches the desired temperature. The heater will turn off when the room reaches the desired temperature and until the room temperature goes below the selected temperature and then it will turn back on. The heating element will turn off, but the fan will continue to operate to cool the internal before shutting off completely.

The Timer button (⑨) is equipped with three (3) settings: two hours (2h), four hours (4h) and eight hours (8h). The timer option will illuminate once selected. The timer is not on if none of those three (3) timer settings are illuminated.

To turn the unit off, push the Power Button Icon (U). The heating element will turn off, but the fan will continue to operate to cool the internal before shutting off completely.

Safety Features (HCE210 & HCE220 Series)

This heater is equipped with several devices and features for added protection:

• Two high temperature safety sensors prevent overheating. If activated, unplug the device and wait at least 10 minutes or allow the unit to cool completely. Make sure the operating conditions are safe and then plug the heater back in and follow the OPERATION instructions.
• Made with high temperature plastic and a cool to touch housing and handle.
• HCE220 Series Only: An Auto Shut Off feature will turn the heater off after 8 hours of use. When the unit is powered on, it automatically defaults to the 8h Timer Selection for this added feature.
• Unit is equipped with a Tip Over switch, which will automatically shut off unit if the device is tipped over.

Cleaning

We recommend that the heater be cleaned at least once a month and before off-season storage.

Turn the heater OFF and unplug it. Allow it to cool.

Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES, POLISHES OR ANY CHEMICAL SOLUTION.

Storage

Clean your heater using the above-mentioned steps. Wrap the cord around the unit. Place in its original box and store it in a cool, dry place.

Troubleshooting

If your heater shuts off unexpectedly or fails to operate, one of your heater safety features may have been activated to prevent overheating.

• Be sure it is plugged in and that the electrical outlet is working.
• Check for any obstructions. If you find an obstruction, turn the heater OFF and unplug it. Allow the heater to cool completely, then remove the obstruction. Wait at least 10 minutes, then plug the heater back in and follow the OPERATION instructions.

Product Specifications

Operation Cost*: To estimate the cost to operate this heater, multiply the watts used by 0.001 to convert into kilowatts, then multiply by your local kilowatt electric rate for however long you run the heater.

For example, if your electric rate is $0.1326** per kilowatt hour and you ran this heater in constant high mode (1500 Watts) for 4 hours, it would cost you $0.80 cents to run the heater (1500 Watts x 4 hours x 0.001) x $0.1326kwp = $0.80 cents.

NOTE: Because the Low setting does not require as much electricity to operate, it is more energy efficient and may be a better option if you are concerned about the higher power consumption when the heater is on the High setting.

*Calculation (Total Wattage x 0.001 x hours used) x Cost per Kilowatt Hour = Cost to operate

**Average Retail Price of Electricity to Ultimate Customer by End-Use, US Energy Information Administration, July 2020.

Consumer Relations

Call us toll-free at: 1-800-477-0457

E-mail: HoneywellPluggedIn.com/contact-us

Or visit our website at: www.HoneywellPluggedIn.com

Please be sure to specify a model number.

NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CONSUMER RELATIONS FIRST OR SEE YOUR WARRANTY. DO NOT RETURN THE PRODUCT TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE MOTOR HOUSING YOURSELF, DOING SO MAY VOID YOUR WARRANTY AND CAUSE DAMAGE TO THE PRODUCT OR PERSONAL INJURY.

3 Year Limited Warranty

YOU SHOULD FIRST READ ALL INSTRUCTIONS BEFORE ATTEMPTING TO USE THIS PRODUCT.

A. This 3 year limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty. KAZ IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.

B. At its option, Kaz will repair or replace this product if it is found to be defective in material or workmanship.

C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.