Newline Z Pro Series Interactive Flat Panel Display

Quick Start Manual

Welcome to the world of NEWLINE. Thank you for choosing the NEWLINE Z Pro Series Interactive Flat Panel Display. Please use this document to get the most out of your screen.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

NOTE 1: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

The symbol of the crossed out wheeled bin indicates this product should not be placed in municipal waste. Instead, dispose of waste equipment by handing it over to a designated collection point for the recycling of electrical and electronic equipment.

Symbol Conventions

Symbols are used in this document to indicate operations that need particular attention. The symbols are defined as follows:

Safety Instruction

For your safety, please read the following instruction before you use the product. Serious injury or property damage may be caused by improper operations. Do not try to repair the product on your own.

WARNING

Disconnect the product from the power supply immediately if major failures occur. Major failures include the following:

• If smoke, a peculiar smell or an abnormal sound is discharged from the product.
• No image or sound is displayed, or the image error occurs.

In the preceding scenarios, do not continue to use the product. Disconnect power supply immediately and contact professional staff for troubleshooting.

Do not drop any liquids, metal or anything combustible onto the product.

• If any liquid or metal are dropped onto or into the product, power off the product and disconnect the power supply, then contact professional staff for solutions.
• Pay attention to children when they are close to the product.

Put the product on a stable surface. An unstable surface includes, and is not limited to an inclined plane, a shaky stand, desk or platform, that might cause the product to turnover and be damaged.

Do not open the panel or change the product on your own. High voltage components are installed in the product. When you open the panel, high voltage, electric shock, or other dangerous situations may occur. If inspection, adjustment, or maintenance is required, contact the local distributor for help.

Use the provided power supply.

• To prevent the product from being damaged, do not use any types of power cables other than the one provided with the product.
• Use a three-wire socket and ensure that it is properly grounded.
• Pull out the power plug from the socket if the product is not used for a long period.

Clean the power plug regularly.

• Fire or electric shock may be caused if the product is powered on, while you are cleaning.
• Pull out the power plug before cleaning it with a dried cloth.

Do not put items on the top of the product.

• Do not put items, such as a container for liquid (a vase, flowerpot, cosmetics or liquid medicine) on the top of the product.
• If any water or liquid is spilled on the product, the product may short circuit cause fire or electric shock.
• Do not walk on or hang any items on the product.

Do not install the product in an improper place.

• Do not install the product in humid places, such as the bathroom, the shower room, near windows, or outdoor environments that experience rain, snow or other harsh weather.

WARNING

Avoid installation near hot spring vapor. The preceding environments may cause faults in the product or electric shock under extreme conditions.

• Do not put an exposed fire source, such as a lit candle on the product.

Pull out the power supply during thunderstorms.

• Do not touch the product during a lighting storm, you may experience an electric shock.
• Install or place components that supply high enough voltage to cause personal injury out of the reach of children.

Do not touch the power cable with wet hands.

CAUTION

Do not install the product in high temperature environments.

• Do not install the product near a heat source, such as a radiator, a heat reservoir, a stove or other heating products.
• Do not expose the product to direct sunlight, which may cause high temperatures and subsequent faults in the product.

When transporting the product:

• Pack the product for transport or maintenance by using the cartons and cushioning material provided with the product.
• Move the product vertically during transport. The screen or other components are easily broken if the product is moved in an improper way.
• Before you move the product, disconnect all external connections and separate all topple preventing products. Move the product carefully to prevent it from being hit or squeezed, especially the screen, which may cause injury if broken.

Do not cover or block up any vents on the product.

• Any overheated components may cause fire, damage the product, and shorten the service life.
• Do not lay the product down in a way where the venting surface will be covered.
• Do not install the product on carpet or cloth.
• Do not use a cloth such as table cloth to cover the product.

Keep the product away from the radio. The product complies with the international EMI standard to prevent radio interference. However, interference may still exists and causes noise in the radio. If noise occurs in the radio, try the following solutions.

• Adjust the direction of the radio antenna to avoid the interference from the product.
• Keep the radio away from the product.

If the screen glass is broken or falls off.

• Keep all personnel 10 feet away from the screen to ensure safety.
• Do not perform any installation or disassembly while the screen glass is broken or has fallen off.

CAUTION

Do not damage the power cable.

• Do not damage, change, twist, bend, or forcibly drag the power cable.
• Do not put weights (such as the product itself) on the power cable.
• Do not forcibly drag the cable when you pull out the power plug. If the power cable is damaged, please contact the local distributor to repair or replace it.
• The power cable in the accessory box is for this product only. Do not use it on other products.

Additional advice:

• Use the product in an environment with comfortable lighting. It is harmful to your eyes to watch in a too bright or too dark environment.
• Relax your eyes watching for a period of time.
• Keep sufficient distance from the product to protect your eyes and prevent eyestrain.
• Adjust the volume to an appropriate level, especially at night.
• Use amplifier equipment as the audio input source with caution. If you must use amplifier equipment, the input power should not exceed the maximum of speaker power. Otherwise, the speaker can become overpowered and damaged.

About USB port.

Rear USB 3.0/USB 2.0 ports switch connections based on signal sources. If the current signal source is reading the data from an external product connecting to the port, please switch the signal source after the data reading is complete. Otherwise, the data or product may be damaged.

1.1 Parts

Front View

55" / 65" / 75" / 86"

65" / 75" / 86"

NOTE

• SDM-S is Smart Display Module Small.
• The product images shown are for illustration purposes only and may not be an exact representation of the product.

1.2 Ports

CAUTION

• Rear USB 3.0 ports switch connections based on signal sources. If the current signal source is reading the data from an external product connecting to the port, please switch the signal source after the data reading is complete. Otherwise, the data or product may be damaged.
• For USB use, USB 3.0 provides up to 900 mA of power. Please make sure the USB flash drive is formatted to FAT32 before inserting into the panel.

Input/Output Ports:

Display Port, HDMI, HDMI In, Line In, S/PDIF In, USB (for firmware upgrade), Public USB 3.0, USB 3.0, USB (for PC), USB Touch, USB 3.0 Touch, Type-C, Type C w/PD, Type C on top side.

Audio Ports:

MIC In, Audio Out.

Connectivity:

Wi-Fi Module, AC Output.

Other:

BATTERY (CR2032).

WARNING

The rear power output port supplies 180W (maximum) power. Please contact Newline to purchase the power AC adapter for powering external devices. Please do not connect any products which require power than listed. Doing so may cause injury or damage to the panel.

1.3 Rear Buttons

NOTE

• When users press the power button, users can set the panel to enter shutdown or sleep mode in Settings > Power > Power Option menu.
• Power button will be locked if you activate the power button lock. Long press MENU button for 5 seconds to exit the lock.
• Press the remote control buttons to enable or disable the touch function.

1.4 Remote Control

CAUTION

Carefully read the following instructions before using the remote control to avoid possible faults:

• Do not drop or damage the remote control.
• Do not spill water or other liquids on the remote control.
• Do not place the remote control on a wet object.
• Do not place the remote control directly under sunlight or near a heat source.

2 Installation Guide

2.1 Safety Precautions

Installation Environment

Environmental Requirements:

• Avoid Electric Shock ⚠
• Avoid Strong Magnetic Field ⚠
• Keep Temperature Below 120°F (50°C) ⚠
• Keep Relative Humidity Under 70% ⚠
• Keep Away From Combustible Vapors (gas leaks, etc.) ⚠
• Avoid Any Corrosive Liquids ⚠
• Do Not Use Outdoors ⚠
• Do Not Install Tilted ⚠

Installation Direction

Ensure the panel is installed vertically. Avoid tilting the panel.

2.2 Installation Precautions

Weight Loading

Weight of the panel:

• 55INCH: 61.7 lb / 28 kg
• 65INCH: 78.3 lb / 35.5 kg
• 75INCH: 103.6 lb / 47 kg
• 86INCH: 130 lb / 59 kg

• When using a mobile stand, ensure that the weight of the product is less than the loading capacity of the mobile stand.
• When using the wall-mount bracket, ensure that the wall can support the weight of the product. Newline recommends that the wall surface be reinforced and have a loading capacity 4 times of the weight of the product. Consult a professional installer for wall-mount installation.

NOTE

Newline does not undertake relevant legal responsibility for any problems caused by improper operation if a third-party mobile stand or wall-mount bracket is used.

• Do not install the product where it might be hit by an opening or closing door.

Vertical installation

When installing the panel, try to keep the panel vertical. An excessive tilt angle may cause damage to the glass or other internal components.

• Product Horizontally ✅
• No Vertical Installation ❌
• Do Not Install Tilted ❌
• Do Not Lay Flat ❌

NOTE

For any problem, please contact the support desk. Newline is not responsible for any damage or losses incurred by users if the users fail to follow the instructions.

Ventilation

Ensure adequate ventilation and/or an air-conditioned environment. Newline recommends keeping certain distances from the side of the product to the wall or panels. Ventilation requirements are shown in the following figure:

• Top: ≥ 200mm (7.87in)
• Left/Right: ≥ 100mm (3.94in)
• Bottom: ≥ 200mm (7.87in)
• Back: ≥ 100mm

2.3 Installation

The dimensions of the four bracket mounting holes on the back panel are VESA MIS-F compliant (86 INCH or 75 INCH: 800 x 400 mm / 31.50 x 15.75 in; 65INCH: 600 x 400 mm / 23.62 x 15.75 in). Use metric M8 screws with a length of 10 mm to 15 mm (0.40 to 0.59 in) to secure the touch screen to the mounting system. Dimensions of the mounting holes on the back panel are shown on the following figure.

NOTE

Consult a professional installer to install the display product.

2.4 Installing the Wi-Fi Module

CAUTION

Wi-Fi Module does not support hot plugging. Therefore, you must insert or remove the Wi-Fi Module when the display is powered off. Otherwise, the panel display or Wi-Fi Module may be damaged.

The Wi-Fi Module is in the accessory box with an independent package. Please install it onto the panel referring to the following steps.

Step 1 Unscrew the 2 screws on the Wi-Fi Module port and remove the shielding cover.

Step 2 Insert the Wi-Fi Module into the port on the rear of the panel until firmly seated, using the 2 screws to secure it.

2.5 Installing the Camera (Optional)

The camera is in the accessory box with an independent package. Please install it onto the panel referring to the following steps. Use the two screws along with the camera to fix.

Remove the silicone cover from the middle port on the top of the panel display, then insert the camera. Install 2 fixing screws for secure purpose. Remove the front cover and start using.

2.6 Installing the OPS (Optional)

CAUTION

The OPS does not support hot plugging. Therefore, you must insert or remove the OPS when the display is powered off. Otherwise, the display or OPS may be damaged.

You will need to purchase the OPS separately. Perform the following steps to install the OPS.

Step 1 Unscrew the M4 screws by hand to remove the OPS protective cover.

Step 2 Push the OPS into the OPS port on the rear of the panel until firmly seated, using the M4 screws to secure the OPS.

2.7 Installing the SDM-S (Not included)

CAUTION

The SDM-S does not support hot plugging. Therefore, you must insert or remove the SDM-S when the display is powered off. Otherwise, the display or SDM-S may be damaged.

Newline does not provide SDM-S, but if you have an SDM-S to use, please install referring to the following steps.

Step 1 Unscrew the 2 screws on the SDM-S slot and remove the shielding cover.

Step 2 Insert the SDM-S into the port on the rear of the panel until firmly seated, using the 2 screws to secure it.

NOTE

Please install SDM-S first before you hang the panel on the wall.

3.1 Power On

Step 1 Ensure the power cable is fully seated into the panel and wall outlet before powering on the panel. Please confirm your wall outlet supports a power range of 100 V to 240 V with frequency at 50 Hz / 60 Hz ± 5% and is fully grounded.

NOTE

The power outlet should be installed near the equipment and should be easily accessible.

Step 2 Flip the power switch located on the side of the product to "I".

Step 3 Press the power button on the back panel or on the remote control.

3.2 Power Off

Step 1 Press the power button on the back panel or the power button on the remote control and a Warning dialog box will be displayed.

Are you sure you want to turn off your device now?

[Cancel] [Turn off]

Step 2 In the Warning dialog box, tap Cancel to return to working mode. Tap Turn off to turn off the display, and the power indicator will turn to red.

Step 3 If you want to completely turn off the panel, turn off the rocker switch behind the panel (next to the power socket) and unplug the power cord.

NOTE

• When the panel display is shutdown, the system will first detect whether the OPS Computer is turned off. If not, the system will first turn off the computer before shutdown.
• Please properly shut down the panel before disconnecting the power source or it may cause damage. Accidental power failure may cause damage to the panel.
• Do not repeatedly turn the power on & off in a short period of time as it may cause malfunction.

4 More Information

For More Information

Please visit the Newline website (https://newline-interactive.com) and select your regional website. Once there, navigate to the Support section and click on Downloads. Choose Z Pro Series to download the User Manual for detailed instructions.

Contact Us for Support

Please directly contact the support team within your region.

• USA
  Hotline: +18334699520
  Email: support@newline-interactive.com
• EMEA
  Hotline: +34918043179 / +34680677828
  Email: support_eu@newline-interactive.com
• APAC
  Hotline: +88635504768
  Email: info_ap@newline-interactive.com
• INDIA
  Hotline: 1800-419-0309
  Email: info.in@newline-interactive.com

Newline is committed to product updates and technical improvements. The technical parameters and specifications are subject to change without prior notice. The pictures in this manual are for reference only.

Recycling Information:

This product should not be placed in municipal waste. Dispose of waste equipment by handing it over to a designated collection point for the recycling of electrical and electronic equipment.