DEVO G1 Smart Lock User Manual

Contents

• Hardware Introduction (01-03)
• Compatible Doors (04)
• Parts List (05-06)
• Product Dimension (07-08)
• Installation Overview (09-20)
• Programming Instructions (21-32)
• Troubleshooting (33-34)
• Product Parameters (35-36)

1. Hardware Introduction

(1) Overview

Exterior View:

• Doorbell Button
• Fingerprint Scanner
• Camera
• Touchscreen Keypad
• Cancel/Return/Lock Button
• Emergency Power Supply Port
• Mechanical Key Hole

Interior View:

• Battery Cover
• Battery Charging Port
• Reset Button
• Thumbturn
• On/Off Button Plug

Note: The "Emergency Power Supply Port" is not for battery charging purpose and can only be used for emergency power supply to the lock.

(2) How To Open / Close Lock Cylinder Cover

Press and hold the Lock Cylinder Cover and turn it clockwise/counterclockwise to open it.

2. Compatible Doors

Door Specifications:

• Door Hole Diameter: 1 1/2" / 38 mm
• Door Thickness: 1 3/8" - 2 1/8" / 35mm - 55 mm
• Cross Bore Diameter: 1 1/2" / 38 mm, 2 1/8" / 54 mm
• Backset: 2 3/8" / 60 mm or 2 3/4" / 70 mm
• Minimum Distance: 4" / 10cm

3. Parts List

Included Components:

• Keys
• Exterior Assembly
• Double-sided Tape Mounting Plate
• Mounting Plate
• Lithium Battery
• Interior Assembly
• Plug
• Deadbolt
• Strike Plate and Box
• Screws (Deadbolt/Strike, Mounting Plate, Indoor Assembly)
• IC Card
• Charging cable

4. Product Dimension

Exterior Dimensions:

• Width: 76.06mm
• Height: 183.80mm

Interior Dimensions:

• Width: 76mm
• Height: 176.98mm
• Depth (from door surface): 30.24mm, 32mm

5. Installation Overview

Steps:

1. Install Deadbolt: Check and adjust deadbolt if necessary. Ensure the "UP" direction faces up when inserting into the doorframe.
2. Install Strike Plate: Attach the strike plate and box to the doorframe with screws.
3. Install Exterior Assembly: Attach rubber gasket. Measure cross bore dimension and determine adapter use. Route cable under the latch, ensuring the tailpiece is horizontal. Fix exterior assembly with double-sided tape.
4. Install Interior Assembly: Detach the back cover. Run wires through the back cover. Secure the back cover with appropriate screws (A, B, or C based on door thickness). Tightly fasten screws. Wire to the interior assembly.
5. Mount Interior Assembly: Ensure wires are tucked into the cabin. Rotate thumbturn to the unlocked position before installing.
6. Test Deadbolt: Check if the deadbolt retracts by turning the thumbturn.
7. Charge Battery: Fully charge the battery before first use (approx. 6 hours). Install the charged battery.

Screw Selection Guide:

• 50-55mm door thickness: Use Screw A
• 40-50mm door thickness: Use Screw B
• 35-40mm door thickness: Use Screw C

6. Programming Instructions

(1). User Type

(2). Enter the Door Lock Setting Menu

Wake up keypad -> Verify administrator -> System Setting -> Select desired option (Auto-Lock Mode, Volume Setting, Language Setting, System Initialization) -> Quit.

(3). How to Program User Access Code

Note: The default Administrator code is 123456. Change it before programming. The default code becomes invalid after adding the first administrator password or fingerprint.

Wake up keypad -> Verify administrator -> User Management -> Administrator Use (Add) or Regular User (Add) -> Add fingerprint or passcode -> Confirm. Alternatively, use Delete Users function.

(4). Restore Factory Settings

1. Long press the "Set" button until two beeps and the No. 5 button flashes.
2. The lock will broadcast successful operation.

(5). Set Administrator Password

1. Wake up keyboard, press "#", enter "123456", press "#" to enter the system.
2. In the system menu, press "1" to select user, then press "1" to enter the new administrator password.

(6). Others

• Authentication Attempts: 5 consecutive attempts allowed for fingerprint, password, and IC card. Exceeding this limit locks the system for one minute.
• Low Power: After the ultra-low power alarm, the motor may not work. Replace the battery. If battery power is lower than 10%, it will report low battery.

7. App Operation Guidance

(1). Connect The Lock To Internet

1. Follow the installation instructions to install the smart lock.
2. Download the Smart Life App.
3. Register and log in to the Smart Life App.
4. Calibrate the smart lock and complete Wi-Fi settings in the App.

QR Codes for App Download:

Tuya Smart App available on the App Store and Google Play.

(2). Steps to Access System Networking

Wake up keypad -> Verify administrator -> Network Settings -> Reset Wi-Fi (Add new Wi-Fi) -> "O" indicator flashes, entering Wi-Fi Pairing Mode -> Return. The "O" key blinks when distribution network is activated (Networking effective time: 120S).

(3). Settings

Enter the setting page -> Open the dormant switch. Note: In sleep mode, the device cannot be woken up from the App and can only be triggered from the device, which can greatly reduce power consumption.

(4). Real-time monitoring and Doorbell Calling

Enter the app -> Enter the real-time monitoring preview interface -> Click to talk.

(5). Password Settings

Add temporary password/record -> Set password type (dynamic, valid for 5 minutes) -> Get password.

(6). Device Unbinding

Navigate through Device Information -> Check Device Network -> Settings -> Device Settings -> Offline Notification -> General Settings -> Help Center -> Remove Device -> Remove and Clear Data -> Cancel.

8. Troubleshooting

Questions

• Can't connect to Wi-Fi
• The device is stay offline and cannot reconnect to the network

Answers

• Cannot connect to Wi-Fi:
  • The device only supports 2.4 GHz network.
  • Ensure the lock is in pairing mode.
  • Ensure your phone is connected to a 2.4G Wi-Fi network.
  • Ensure your phone's Bluetooth is turned on.
  • Select the same 2.4G network Wi-Fi on your phone for the device.
  • To test Wi-Fi network requirements, prepare a phone hotspot as a Wi-Fi signal and connect the lock to it. Check router settings for Wi-Fi frequency band and signal stability.
• Device is offline:
  • Check if the lock has entered dormant mode. The APP will be offline when the device is sleeping (refer to page 31).
  • When battery power is lower than 10%, the lock enters low-power mode and disconnects from the network to ensure basic functions. Doorbell network connection is not affected by low battery.

9. Product Parameters

• Power Supply: 3.7V Lithium Battery 10000mAh
• Video: 1080p HD Video, Night Vision
• Emergency Power: 5V
• Fingerprint Capacity: 100 MAX
• Passcodes Capacity: 50 MAX
• IC Card Capacity: 50 MAX
• Fingerprint Pixels: 508dpi
• Identification Speed: 0.25sec
• False Positive Rate: <0.0001%
• Rejection Rate: <0.1%
• Working Temperature: -15°C - 50°C (5°F - 122°F)
• Working Humidity: 0% - 85% (No Condensation)
• Standby Current: < 500 μΑ
• Dynamic Power Consumption: < 600 mA
• Material: Aluminum Alloy
• Passcode Length: Supports 6-10 digits
• Emergency power Interface: Type-C
• Scramble passcodes: Support Scramble Passcode (Add Random Digits Before Or After The Real Passcode). Random Digits No Length Limit.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.