DEVO G3 Smart Lock User Manual

Contents

• Hardware Introduction
• Compatible Doors
• Parts List
• Product Dimension
• Installation Overview
• Programming Instructions
• Troubleshooting
• Product Parameters

1. Hardware Introduction

(1) Overview

The DEVO smart lock features a Fingerprint Scanner, Touchscreen Keypad, Cancel/Return/Lock button, Confirm/Enter button, Doorbell Button, Mechanical Key Hole, and Emergency Power Supply Port. The exterior assembly also includes a Battery Cover, Reset Button, and ON/OFF Button. The emergency power supply port is for emergency power only, not for charging.

Diagram Description:

Exterior View: Shows a circular fingerprint scanner at the top, a numeric keypad (1-9, *, 0, #), a DEVO logo, and an emergency power supply port at the bottom. Buttons for Cancel/Return/Lock, Confirm/Enter, and Doorbell are also visible, along with a mechanical keyhole.

Interior View: Shows the battery compartment, a reset button, and an ON/OFF button.

(2) How To Open / Close Lock Cylinder Cover

Press and hold the Lock Cylinder Cover and turn it clockwise/counterclockwise to open it.

2. Compatible Doors

Compatible Doors

This smart lock is compatible with doors of various dimensions:

• Door Hole Diameter: 1 1/2" / 38mm
• Door Thickness: 35mm - 55mm
• Cross Bore Diameter: 1 1/8" / 28mm or 1 1/8" / 54mm
• Backset: 2 3/8" / 60mm or 2 3/4" / 70mm
• Minimum Distance: 4" / 10cm

Diagram Description: A diagram illustrates a door with callouts for Door Hole Diameter, Door Thickness, Cross Bore Diameter, and Backset, indicating the compatible measurements.

3. Parts List

The DEVO G3 Smart Lock package includes:

• Exterior Assembly
• 2 Keys
• Deadbolt/Strike Screws (Screws A, B, C, D)
• Mounting Plates
• Indoor Assembly
• Plug
• Strike Plate and Box
• Deadbolt
• IC Card

Diagram Description: Images show the exterior and interior assemblies, keys, various screws labeled A, B, C, D, mounting plates, strike plate and box, deadbolt, and IC card.

4. Product Dimension

Exterior Assembly Dimensions:

• Width: 63.92mm
• Height: 147.92mm
• Depth: 73mm

Interior Assembly Dimensions:

• Height: 171mm

Other Dimensions:

• Lock Cylinder Cover Depth: 61.99mm
• Bottom Component Height: 44.23mm

Diagram Description: Detailed technical drawings show the dimensions of the exterior and interior assemblies, including specific measurements for various parts.

5. Installation Overview

Follow these steps to install the DEVO G3 Smart Lock:

1. Install Deadbolt: Check your door for the correct backset (60mm or 70mm). If the backset is 70mm, rotate the faceplate 180°. Ensure the deadbolt is installed with the word "UP" facing upwards.
2. Install Strike Plate: Secure the strike plate and box to the doorframe using the provided screws.
3. Install Exterior Assembly: Measure your door's cross bore dimension. If it's 1 1/2" / 38mm, remove the adapter. If it's 1 7/8" / 54mm, keep the adapter. Route the cable under the latch and ensure the tailpiece is vertical.
4. Install Interior Assembly: Detach the back cover. Run the wires through the back cover. Secure the back cover with the appropriate screws (Screw A for 45-55mm doors, Screw B for 35-45mm doors). Tightly fasten the screws.
5. Fix Exterior Assembly: Use the double-sided tape to attach the exterior assembly.
6. Wire to Interior Assembly: Connect the data cable to the interior assembly.
7. Mount Interior Assembly: Ensure the wire is tucked into the cabin on the back of the interior assembly.
8. Check Deadbolt: Turn the thumbturn to ensure the deadbolt retracts smoothly.
9. Install Batteries: Insert 8 AA batteries, paying attention to the positive and negative poles. The lock is now ready for use.

Diagram Description: Step-by-step illustrations guide the user through the installation process, showing how to attach the deadbolt, strike plate, exterior and interior assemblies, and connect the wiring.

6. Programming Instructions

(1) User Type

The DEVO G3 Smart Lock supports different user types:

• Administrator: 1 user, Sequence ID 1. Manages unlock and other functions.
• Regular User: 199 users, Sequence ID 2-200. Can unlock (invalid when Anti-lock is On).
• Total Capacity: 200 users.
• Capacity Breakdown: Fingerprint Capacity: 100, Passcode Capacity: 50, IC Card Capacity: 50.

(2) Enter The Function Settings Mode

Short press the "Settings" button. You will hear a voice prompt: "Please verify administrator user." Enter the administrator password and press the "unlock" button to confirm. Successful verification enters the setting mode.

Note: When automatic locking is enabled, the lock enters an unlocked state and will automatically close after a set time.

(3) Setting Mode Function List

The setting mode allows for various configurations:

• Add Password: Add Keypad Password
• Delete Password: Delete Password, Delete Number
• Change Admin Password
• Other Function Settings: Auto Lock, Voice Prompt Volume, Language Settings, Broadcast Version Number
• Distribution Network Setup

(4) Restore Factory Settings

1. Press and hold the "Set" button for 4 seconds until a "dong" sound is heard.
2. Press and hold the button until a voice prompt is heard. Press the unlock button to confirm.
3. Press the unlock button within 4 seconds to confirm factory reset.

(5) Set Administrator Password

1. Press the setting button. If no administrator password is set, a prompt will ask you to set one.
2. Enter the administrator password and press the unlock button to confirm.
3. Follow the voice prompts, re-enter the administrator password, and press the unlock button to confirm.

(6) Others

• Error Limit: 5 consecutive incorrect attempts for fingerprints/passwords within 5 minutes will lock the device for one minute.
• Low Battery: When battery power is below 10%, the motor may not work, and a low battery warning will be issued.
• Network Configuration: Ensure the power has just been disconnected and plugged in before configuring the network. The network configuration mode is active for 120 seconds.

Operation Status Table: A table details various operations (e.g., Verify successfully, Battery low, Lock) with corresponding indicator status and voice broadcasts.

7. Troubleshooting

8. Product Parameters

• Power Supply: 4.8V-6V Eight Cell No.5 Battery/2400 mAh
• Emergency Power: 5V
• Fingerprint Capacity: 100 MAX
• Passcode Capacity: 50 MAX
• IC Card Capacity: 50 Max
• Identification Speed: 0.25 Sec
• False Positive Rate: <0.0001%
• Rejection Rate: <0.1%
• Working Temperature: -15°C to 50°C (5°F to 122°F)
• Working Humidity: 0% - 85% (No Condensation)
• Standby Current: 380uA
• Dynamic Power Consumption: 450mA
• Material: Aluminum Alloy
• Passcode Length: Supports 6-8 Digits
• Emergency Power Interface: Type-C
• Scramble Passcode: Support Scramble Passcode

Scramble Passcode Example: 3578 123456 65987 (Add Random Digits Before Or After The Real Passcode, No Length Limit)

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received. This equipment has been tested and found to comply with the limits for a Class B digital device. It generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. If interference occurs, reorient or relocate the receiving antenna, increase separation between equipment and receiver, or connect to a different circuit. Consult a dealer or technician for help. This equipment complies with FCC radiation exposure limits for an uncontrolled environment and should be installed and operated with a minimum distance of 20cm between the radiator and your body.