AMADA Tripod Stand Instruction Manual

Product Overview

Thank you for choosing this AMADA product! At AMADA, we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact us at support@amadahome.com.

Merci d'avoir choisi ce produit AMADA! Chez AMADA, nous nous efforçons de vous fournir les meilleurs produits et services de qualité de l'industrie. Si vous rencontrez des problèmes, n'hésitez pas à nous contacter à support@amadahome.com.

Specifications

Height Adjustable: 22.44" - 36" (570mm - 915mm)

Tray Dimensions: 16.0" (406mm) x 11.0" (280mm)

Important Safety Information

• Check package contents against the supplied parts and hardware list to assure that all components were received undamaged. Do not use damaged or defective parts. If you require replacement parts, please contact customer service at support@amadahome.com.
• Carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact customer service at support@amadahome.com.
• Not all parts and hardware included will be used.
• Do not use this product for any purpose that is not explicitly specified in this manual. AMADA is not liable for damage or injury caused by incorrect assembly or inappropriate use.

Supplied Parts and Hardware

• Foldable Tripod Stand (A): x 1
• Tray (B): x 1
• Connector (C): x 1
• M4 x 10mm Bolt (D): x 5
• Phillips Screwdriver (Not Included)

Assembly Instructions

Step 1: Adjust the Height of the Tripod

1-1. Slightly loosen the height adjustment knob. Be careful to avoid pinch areas when unfolding or folding the tripod. Do not place hands on or near the joints of the supporting leg.

1-2. When you adjust the pillar to your desired height, tighten the knob, then insert the safety pin into the hole on the pillar. Tighten the bolt [S] using a Phillips screwdriver.

Step 2: Secure the Connector to the Top of the Tray Support Leg

Align the connector with the top of the tray support leg and tighten the knob.

Step 3: Secure the Tray to the Connector

Note:

• The holes in the connector should be aligned with the holes on the tray.
• Do not tighten the bolts [D] until all of them are in the correct positions.

Attach the tray to the connector using the bolts [D] and a Phillips screwdriver.

Step 4: Tilt and Height Adjustment

Tilt Adjustment of Tray

Slightly loosen the tilt adjustment knob [K] to adjust the tilt angle. When you have adjusted the tray to your desired tilt angle, tighten the knob [K] to secure the height in place.

Height Adjustment of Tray Support Leg

1. Remove the safety pin [M] from the tray support leg.
2. Slightly loosen the height adjustment knob [N] to adjust the height.
3. When you adjust the tray support leg to your desired height, tighten the knob [N] and insert the safety pin [M] into the hole of the tray support leg. Tighten the bolt [S] using a Phillips screwdriver.

Height Adjustment of Tripod Stand

1. Slightly loosen the height adjustment knob [O] to adjust the height of the tripod stand.
2. When you adjust the tripod stand to your desired height, tighten the knob [O] to secure the height in place.

Final Message

Thank you again for choosing this AMADA product! We hope that you are as happy with your product as we are designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don't hesitate to contact us at support@amadahome.com.

Nous tous chez AMADA apprécions votre achat de produit. Nous espérons que vous êtes aussi satisfait de votre produit que nous le concevons et le fabriquons pour vous. Nous nous efforçons de vous fournir les meilleurs produits et services de qualité dans l'industrie. Si vous rencontrez des problèmes, n'hésitez pas à nous contacter à support@amadahome.com.

Document Revision: 860-00292-00 Rev01