STAND-ALONE PHASE DIMMER & SWITCH

Product Identification

Overview

The SENSORWORX phase dimmer provides manual dimming control of 120V lighting from a single location. With no minimum load requirements, this stand-alone dimmer is perfect for any lighting zone. Additionally, at less than one inch deep, the unit is significantly shallower than typical dimmers. This results in less crowded wall boxes and quicker installation. All SENSORWORX products are proudly made in the USA.

Features

Electrical Features

• Dims LED, CFL, ELV, & Incandescent Lighting Loads
• Selectable Reverse (default) and Forward Phase Dimming in Same Unit
• No Minimum Load Ratings - Relay Based Switching (i.e. non-Triac)
• Overload Protection Monitors & Protects Unit from Overheating

Physical Features

• Enclosure is 25-40% Shallower than Other Wall Dimmers (< 1" Depth into Wallbox)
• Modern Look and Individual Easy-Tap Buttons for On, Off, Raise, & Lower
• Matches Styling of other SWX Wall Devices
• Self-Grounding Mounting Strap
• Blue Locator LED when Lights are Off

Operational Features

• White LED Indicator Changes Intensity as Dim Level is Adjusted
• Configurable Dimming Parameters including High/Low Trims, & Turn on Levels
• Programmable Dimming Curves
• Settings are Adjustable without Removing Cover Plate
• Unit Retains Level Setting after Power Outage

Specifications

Electrical

OPERATING VOLTAGE: 120VAC, Single Phase, 50/60 Hz

LOAD RATINGS:

• MAX: 150W CFL/LED
• 375W ELV
• 375W Incandescent/Halogen
• MLV (consult factory)

MIN LOAD: None

LOAD TYPES:

• Electronic Low Voltage
• LED Driver/Lamps
• CFL, Electronic/Magnetic Ballasts (Fluorescent)
• Tungsten (Incandescent)
• Halogen
• MLV (consult factory)

ESD IMMUNITY: Tested to withstand electrostatic discharge without damage or memory loss.

SURGE IMMUNITY: Tested to withstand surge voltages without damage or loss of operation.

NON-VOLATILE MEMORY: Saves all settings even if power is disrupted.

Physical

SIZE: 2.74"H x 1.68"W x 1.39"D (6.96 x 4.27 x 3.53 cm)

WALLBOX DEPTH: <1" Wallbox Mounting Depth

WEIGHT: 4.5 oz

MOUNTING: Single Gang Switch Box

LED STATUS INDICATOR: Bi-color White & Blue; White LED Intensity

Environmental

OPERATING TEMP: 32°F to 86°F (0°C to 30°C) (for full load operation)

RELATIVE HUMIDITY: 0-95% Non-Condensing (Indoor Use Only)

[UL Listed] [Made in USA] [BAA Compliant] [TAA Compliant] [Lead Free] [RoHS Compliant]

Installation

• Designed to mount in a 1-gang wall box with 3.28" hole spacing.
• Units can also share multiple gang wall boxes with other devices.
• Unit face is field removable to change colors. Contact factory for additional faces.

Wiring

Dimming from a Single Location

Diagram Description: A wiring diagram shows connections for a single location. A 120V AC source (N - Neutral, BLK - Hot) connects to the dimmer. The dimmer has WHT (Line), BLU (Dimmed Output), and GRN (Ground) terminals. The BLU terminal connects to the DIMMABLE LOAD.

Visual Representation:

[Wiring Diagram: 120V AC Source (N, BLK) to Dimmer (WHT, BLU, GRN). Dimmer (BLU) to Dimmable Load.]

Dimming from Multiple Locations (e.g. 3-way)

This phase dimmer is not designed for installation or usage in multiway (e.g. 3-way) applications. For dimming in those applications, the SENSORWORX wireless phase dimmer (model series SWX-874) and a wireless companion dimmer (model series SWX-854) is required.

Dimming Operation Notes

• Rapid dimming adjustments can be made by holding the UP or DOWN buttons.
• Small dimming adjustments are made by tapping the UP or DOWN buttons.
• The intensity of the white LED will change accordingly as dimming is adjusted.
• When the level reaches the high or low trim level, the white LED will begin to blink.
• There are always 20 steps of dim level adjustment from high trim to low trim (or reverse). Rapid button presses may result in misses.
• For more responsive level adjustments when lighting is at the low end, it is recommended to use the logarithmic dimming curve.
• The logarithmic dimming curve should not be used with an LED driver that has a preprogrammed logarithmic dimming response.
• If the unit reaches an elevated temperature due to overloading, it will either drop to 40% dimming level or open the relay to reduce the temperature. If auto-dimming does not reduce the temperature within 5 minutes, the unit's relay will be opened. If the unit is already at a dimmed state less than 40% when elevated temperature is reached, the unit will open its relay without further dimming first. The relay will remain open for at least one minute or until the unit's temperature has dropped to an acceptable operating level. If auto-dimming or turning off is observed, the dimming load should be reduced.

Configuration

Dimmers have several configurable functions depending on the specific model. All functions' setting values can be accessed and changed through a push-button sequence and observing the LED feedback.

Configuration Programming

1. From the lists of Configuration Functions below, note the Button ID and number (#) of the Function to be changed. For example, HIGH TRIM setting is the Up Button, #3.
2. Enter programming mode by pressing and holding the ON button until the blue LED begins rapid flashing, then release.
3. Press and release the particular button (UP, DOWN, or ON) that is applicable the number of times for the chosen function. For example, press the UP button 3 times for the HIGH TRIM setting.
4. The LED will flash back white the number of times equal to the current setting number as it appears in each function's detailed table of values. For example, the default HIGH TRIM is setting #2 (10V). Following a short pause, this blink back sequence will repeat.
5. Interrupt blink back by pressing the applicable button the number of times corresponding to the new setting #. For example, UP button 3 times (for 9V).
6. The LED will flash back the new setting number as confirmation.
7. To Save and Exit programming mode, press and hold the function's applicable button again until the LED changes to White, then release. The LED will then blink white twice as confirmation of success. [Note]: To Exit without saving during any step, wait until unit double flashes blue.

[Note]: If the LED double flashes twice blue at any point, repeat the above procedure.

Configuration Function Overview

Diagram Description: A diagram illustrates the dimmer's buttons and LED indicator. The buttons are labeled OFF, UP, DOWN, and ON. The LED indicator is central. The diagram shows how these buttons map to different function categories: UP Button Functions, DOWN Button Functions, and ON Button Functions.

UP BUTTON FUNCTIONS:

DOWN BUTTON FUNCTIONS:

ON BUTTON FUNCTIONS:

Configuration Setting Details

Functions Accessed Through the "ON" Button

Function #4 - Phase Dimming Type

Function #7 - LED Behavior

The functionality of the indicator LED on the dimmer when no buttons are being pressed.

Function #8 - Restore Factory Defaults

Functions Accessed Through the "UP" Button

Function #2 - Turn On Level

The lighting level upon initially turning on. [Note]: Changes to this setting will not be observed until the lights have cycled off and back on one time.

Function #3 - High Trim

The maximum level of the full dimming range that is allowed by the dimmer.

Function #4 - Fade On Time

The time it takes for a dimming output to reach its final level when turning on.

Function #5 - Dimming Curve

The curve that dictates the dimming adjustment step size.

Functions Accessed Through the "DOWN" Button

Function #2 - Turn Off Scheme

The actions of the dimmer when the off switch press is pressed.

Function #3 - Low Trim

The lowest % of the dimmer's full range to which a user can dim.

Function #4 - Fade Off Time

The time it takes the dimmer to reach the low trim level when the off button is pressed. This setting is only active when the unit's Turn Off Scheme is set to one of the Fade settings.