Sealey - Leading Professional Tool & Workshop Equipment Supplier
Instructions for SEALEY models including: SSP1.V6 Goggles Direct Vent, Goggles Direct Vent, Direct Vent, Vent
Sealey SSP1 Safety Goggles Direct Vent | workshopping.co.uk
Safety Goggles Direct Vent | Vinnybyrne.com
Sealey SSP1 Worksafe Direct Vent Safety Goggles » Product
File Info : application/pdf, 2 Pages, 316.80KB
DocumentDocumentSAFETY GOGGLES - DIRECT VENT MODEL NO: SSP1.V6 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. 1. INTRODUCTION Direct ventilation allows for maximum airflow to prevent fog. Elasticated strap holds the goggles securely in place. Soft rim provides optimum comfort for long periods of use. BS EN 166 Impact and scratch resistant durable polycarbonate lens provides protection against projectiles. Notified Body: 2797. Type Examination Certificate Number: CE 691450. Carried Out By: BSI Group. 2. SAFETY 9 Always perform a risk assessment and follow correct health and safety procedures before using this product. WARNING! Safety glasses with polycarbonate lenses are impact resistant but may break under severe impact. WARNING! Materials which may come into contact with the wearer's skin could cause allergic reactions to susceptible individuals. WARNING! Scratched or damaged oculars should be replaced. WARNING! Eye protectors against high speed particles worn over standard ophthalmic spectacles may transmit impacts, thus creating a hazard to the wearer. 8 DO NOT use tinted or clear lenses when welding or performing other operations which expose your eyes to harmful levels of radiation. 8 DO NOT use for grinding or welding. IMPORTANT: if protection against high speed particles at extremes of temperature is required, then the selected eye-protector should be marked with the letter `T' immediately after the impact letter, i.e. FT, BT or AT. If the impact letter is not followed by the letter `T' then the eye protector shall only be used against high speed particles at room temperature. If the symbols F, B and A are not common to both the ocular and the frame then it is the lower level which shall be assigned to the complete eye-protector. 3. APPLICATIONS 3.1. EN 166 CATEGORISATION · Optical Class 1 - suitable for work with high vision requirements for permanent use. 3.2. FIELD OF USE · B - High speed particle, medium energy impact. · 3 - Protection against droplets of liquids. 4. MAINTENANCE 4.1. CLEANING 8 DO NOT use abrasive materials. 9 Using a soft and clean brush or cloth, use warm suds to wash and clean. Ensure hands are clean (without grease). 9 Materials which may come into contact with the wearer's skin could cause allergic reactions to susceptible individuals. The contact areas should be disinfected regularly. 4.2. STORAGE 9 Store in a bag or case out of direct sunlight, away from chemicals and abrasive substances, in a clean dust free environment. 9 Use original bag for transportation if possible. 4.3. OBSOLESCENCE Like all protective products, the life depends on the type of use, care and maintenance. If damaged, replace the entire article. In every case, the product must be replaced after a period of two years. © Jack Sealey Limited Original Language Version SSP1.V6 Issue 2 (1) 27/02/24 This document has been drawn up according to Regulation (EU) 2016/425 as amended to apply to GB for Personal Protective Equipment. The declaration of conformity can be accessed at www.sealey.co.uk. ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. REGISTER YOUR PURCHASE HERE Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. EU | Sealey EU Ltd, Farney Street, Carrickmacross, Co. Monaghan, A81 PK68 Ireland UK | Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk www.sealey.co.uk © Jack Sealey Limited Original Language Version SSP1.V6 Issue 2 (1) 27/02/24