User Manual for Rayrun models including: P30 RGB Wireless Remote LED Controller, P30, P30 -S LED Controller, RGB Wireless Remote LED Controller, RGB LED Controller, Wireless Remote LED Controller, LED Controller, Wireless LED Controller, Remote LED Controller, Controller
P30 Pro. CV RF RGB LED controller-Rayrun
Wireless Remote Control
RGB LED Controller
Model: P30(-S)
Introduction
P30 RGB LED controller is designed to drive constant voltage LED products in voltage range of DC5-24V. The main unit works with a RF remote controller, user can setup LED color, brightness and dynamic effects from the remote controller. The main unit is powered by DC power supply and receives remote controller commands to drive LED fixtures.
Full Protection
High Power
Waterproof
Compact Size
Wireless Remote Wide Voltage Range
Wiring & Indicator
1. Power supply input
The controller supply voltage range is from DC 5V to 24V. The red power cable should be connected to power positive and black to negative. (For other cable color, please refer to the labels). The LED output voltage is at same level as the power voltage, please make sure the power supply voltage is correct and the power rating is capable for the load.
2. LED output
Connect constant voltage LED loads. Please make sure the LED rated voltage is same as the power supply and each channel's maximum load current is in range of the controller rated current. The black cable should be connected to LED positive, the green, red and blue cable should be connected to the LED negative cable with the same color.
3. Work status indicator This indicator shows all working status of the
controller. It displays different events as following: Steady blue: Normal working. Short white blink: Command received. Long single white blink: Mode or color cycle edge. Single yellow flash : Edge of the content. Red flash: Overload protection. Yellow flash: Overheat protection. White blink for 3 times: New remote paired.
4. Wiring diagram Please connect the controller output to LED loads
and power supply to the controller power input. The power supply voltage must be same as the LED load's rated voltage. Check all cables to be well connected and insulated before power on.
To 110/230 5-24V DC output AC power Power supply
P30 LED Controller
Constant voltage LED load
5-24V DC
5-24V Driving
Remote Controller
Functions
5. Turn ON / OFF Press `I' key to turn on unit or press `O' key to turn off.
Main unit will memorize the on/off status and will restore to the previous status on next power on.
Please use remote controller to turn on the unit if it was switched to off status before power cut.
8
Press within 10 seconds after receiver powered on
Pair new remote
6. Static RGB color setting The keys in this area set the RGB static color and
brightness. Press the colored keys to set the RGB LEDs to correspond color as shortcut.
For other static colors, please press COLOR and COLOR keys to select from the preset library colors.
Press and keys to adjust color brightness.
7. Dynamic mode setting These keys control the RGB dynamic modes. Press MODE
and MODE keys to select dynamic modes and press and keys to set the running speed of the dynamic modes.
Press key to play the dynamic modes in loop with each mode repeating for 3 times.
8. Remote indicator
This indicator blinks when remote controller is working. If the indicator flash slowly when pressing keys, it means the remote battery is nearly empty and please change the battery in this case. The battery model is CR2032.
Operation
9. Using the remote controller Please pull out the battery insulate tape before
using. The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts.
10. Pair a new remote controller The remote controller and main unit is 1 to 1 paired as
factory default. It's possible to pair maximum 5 remote controllers to one main unit and each remote controller could be paired to any main unit.
User could pair a new remote controller to main unit by following two steps:
1). Plug off the power of main unit and plug in again after more than 5 seconds.
2). Press and key simultaneously for about 3 seconds, within time of 10 seconds after the main unit powered on.
11. Keep current remote only
In some cases, one main unit might be paired with several remote controllers but extra remote controllers are no longer needed. User could simply pair the current using remote to main unit again, then the main unit will dis-pair all other remote controllers and recognize current one only.
Advanced features
12. Waterproof (-S version)
The IP-68 waterproof feature with glue injection finish is available on -S version controllers. For overall waterproof performance, the cables must be waterproof treated separately.
Wireless signal degrade : The wireless communication ability could degrade when using at wet environment, please be aware that the wireless control distance will be shortened in such case. 13. Protection function
The controller has full protection function against wrong wiring, load short circuit, overload and overheat. The controller will stop working and the indicator will flash with red / yellow color to indicate the malfunction. The controller will try to recover from protection status in a short time when the working condition is good.
For protection issues, please check the situation with different indicator information:
Red flash: Check the output cables and load, make sure no short circuit and the load current is in rated range. Also the load must be constant voltage type.
Yellow flash: Check the installation environment, make sure in a rated temperature range and with good ventilation or heat dissipation condition.
Dynamic effects
Dynamic effects Multi-color fade Single color fade
Effect Pattern
Dual-color fade
Multi-color flash Single color flash Single color strobe
Specification
Model Dynamic mode
Static color PWM grade Color brightness grade Speed grade Direct color select Overload protection Overheat protection Working voltage Remote frequency Remote control distance Rated output current Waterproof
P30
P30-S
34 modes
30 colors
4000 steps
5 levels
10 levels
7 direct keys
Yes
Yes
DC 5-24V
433.92MHz
>15m at open area
3x5A
IP63
IP68
RF
RGBLED
:P30(-S)
P30RGBLED5V 2 4 VL E D L E D L E D LED LED
1. 5V24V
L E D
2.LED L E D L E D
LED LED
3.
3
4. LED
L E D
5-24V
5-24VDC
LED
LED
RF
5. "I " "O "
8
10
6.RGB R G B
L E D COLOR COLOR
7.RGB MODEMODE
3
8.
CR2032
9. R F
10.
11 1 5
1 5 210 3 3 11.
12.IP68(-S)
-S I P 6 8
13.
RGB RGB PWM
P30
P30-S
34
30
4000
5
10
DC5-24V
433.92MHz
>15
3x5A
IP-63
IP-68
Corel PDF Engine Version 18.1.0.661 CorelDRAW X8