Outsunny 840-014V01 Pop-Up Gazebo
Model: 840-014V01 | Reference: IN221200424V02_GL
Important Information
IMPORTANT: RETAIN FOR FUTURE REFERENCE: READ CAREFULLY.
Warnings and Safety Precautions
- Find a flat and stable surface large enough to set up the folding pavilion. Carefully take the tent frame out of the bag and place it on a dry surface (sand, grass, or firm surface).
- Follow these instructions carefully to avoid getting your hands and fingers caught in the moving parts of the frame when opening and closing. You need at least two people to safely assemble and dismantle the folding pavilion. Do not try to set up the tent by yourself, as pulling on one side can overload the tent legs and damage them unnecessarily. To avoid damage, the tent must be pulled out in tandem.
- In windy conditions, secure the tent using the ropes attached to each side of the canopy. Attach the ropes to the pegs at a 30-degree angle and anchor them to the ground with a hammer ?. If the canopy is placed on a hard surface, secure the 4 sides with bricks ? or sandbags ?.
- Do not set up the pavilion in windy weather conditions. This can lead to injuries and/or damage to your tent.
- Do not use chemical additives to clean the roofs and side walls. The water temperature can be a maximum of 30°C.
- Make sure that you pack the folding tent dry and store it upright in the bag provided in a dry place. A damp tent can get mold stains.
- No liability is accepted for damage caused by improper storage or cleaning.
- Please take appropriate actions as heavy rain, wind, and snow can damage the tent. If necessary, please disassemble and store for later use.
- In snowy conditions, please do not allow the thickness of the snow to be more than 5cm on the roof; this should be cleared as soon as possible for your safety.
Assembly Instructions
Parts List
- A: Frame Poles (x1)
- B: Canopy (x1)
- C: Net Wall (x1)
- D: Tent Pegs (x4) ⛺️
- E: Ground Stakes/Hooks (x4)
- F: Guy Ropes (x4) ?
Step 1: Extend Frame
Extend the main frame structure by pulling outwards from opposite sides. This typically requires two people working in tandem.
(Visual description: An illustration shows two people standing on opposite sides of a folded frame, pulling outwards to begin extending it.)
Step 2: Attach Roof Canopy
Lay the roof canopy over the extended frame.
Position each corner of the roof canopy at the top of each frame pole.
(Visual description: An illustration shows the fabric canopy being draped over the extended frame structure, with individuals aligning the corners of the canopy with the top of the vertical poles.)
Step 3: Secure Roof Canopy
Secure each corner of the roof canopy to the top of each frame pole using the provided fastening tabs.
Ensure the roof canopy completely covers all sides of the roof frame.
(Visual description: A close-up illustration shows fastening tabs being used to attach the canopy to the frame poles.)
Step 4: Extend and Lock Roof Frame
Position one hand below the roof frame. Standing at opposite corners, pull out the roof frame to extend it fully.
At the same time, push up the roof frame with the other hand until it 'clicks' into the locked position. Repeat this action at all four corners.
Climb under the roof canopy and secure the fastening tabs to the underside of the roof canopy, connecting them to the internal cross bars of the roof frame.
(Visual description: Illustrations show individuals pulling outwards on the frame corners and pushing upwards to lock the frame sections, followed by securing the canopy to the frame's internal structure.)
Step 5: Extend Poles to Height
Standing at opposite corners on the pole base, pull up the roof frame by holding the lower section of the pole.
Pull up the roof frame until the pole 'clicks' into the correct height position. Repeat for all poles.
(Visual description: An illustration shows individuals pulling upwards on the lower sections of the poles to extend the height of the gazebo until they lock into place.)
Step 6: Fit Net Wall
Connect the net wall with the beam pole using the Nylon buckles ?.
Ensure the zipper door ? is positioned in the middle and on the opposite side.
(Visual description: An illustration shows the mesh side walls being attached to the frame poles using buckles, with attention to the placement of the zippered entrance.)
Step 7: Secure Gazebo to Ground
Secure the gazebo by driving one tent peg ⛺️ through the hole on each of the pole bases into the ground.
Tie one end of each guy rope ? to each corner of the roof canopy using the provided tabs.
Secure the other end of each guy rope to the ground using a tent peg ⛺️.
Using the provided plastic runner, tighten the guy rope to secure your gazebo firmly to the ground.
(Visual description: Illustrations show tent pegs being driven into the ground, guy ropes being attached to canopy corners and then to pegs, and a plastic runner being used to tension the ropes.)
Contact Information
For any questions or assistance regarding your Outsunny product, please contact the relevant customer care center for your region. Details can be found in the original documentation or on the manufacturer's website.
Imported by Aosom LLC and its affiliates.
