Manuals+

FORNO Espresso 30" Wall Ovens Installation Guide

Models: 30" Single Wall Oven-Mechanical Control, 30" Double Wall Oven-Mechanical Control
Model Number Series: FBOEL1370-30BLK | FBOEL1324-30BLK

Read these instructions carefully before using your appliance, and keep them for future reference. Following these instructions will ensure your appliance provides many years of good service.

Document Date: 03/2025

Oven Safety

Your safety and the safety of others are very important. Many important safety messages have been provided in this manual and on the appliance. Always read and obey all safety messages.

⚠ This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER,” “WARNING,” or “CAUTION.”

All safety messages will tell you what the potential hazard is, how to reduce the chance of injury, and what can happen if the instructions are not followed.

Installation Requirements

State of California Proposition 65 Warnings

⚠ WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

⚠ WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other reproductive harm.

Tools and Parts

Gather the required tools before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed:

  • Measuring Tape
  • Straightedge
  • Pencil
  • Phillips Screwdriver
  • Level
  • Wire Cutters and Wire Stripper
  • Hand or Sabre Saw
  • 1" Hole Saw
  • Cordless Drill and Drill Bit
  • Safety Gloves and Goggles
  • Volt Meter (0-250VAC)

Parts Needed:

  • UL Listed Conduit Connector
  • UL Listed Wire Connectors

Parts Provided:

  • #8-14 x 1" Screws - Single Ovens (2), Double Ovens (4)

Technical Data

OVENDIMENSIONElectrical Ratings and Maximum Connected Load
Single Built-in Oven30" (76 cm)@ 240 Volts 60 Hz
Amperes: 14.8
Watts: 3550
Double Built-in Oven30" (76 cm)@ 240 Volts 60 Hz
Amperes: 29.6
Watts: 7100

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Product Dimensions

Diagrams illustrate single and double ovens with labeled dimensions (a-e).

LetterSingle Oven DimensionsDouble Oven Dimensions
a287/16" (72.2 cm) Height (overall)513/16" (130.0 cm) Height (overall)
b281/2" (72.4 cm) Width (recessed)281/2" (72.4 cm) Width (recessed)
c273/16" (69 cm) Height (recessed)4915/16" (126.8 cm) Height (recessed)
d231/2" (59.7 cm) Depth (recessed)231/2" (59.7 cm) Depth (recessed)
e297/8" (75.9 cm) Width (overall)297/8" (75.9 cm) Width (overall)

Opening Dimensions

Diagrams illustrate single oven installed in cabinet, single oven installed undercounter, and double oven installed in cabinet, with labeled dimensions (a-g).

Single Oven Undercounter w/o CooktopSingle Oven in CabinetDouble Oven in Cabinet
aWidth (cutout)285/8" (72.7 cm)285/8" (72.7 cm)285/8" (72.7 cm)
bHeight (cutout)271/2" (70 cm)271/2" (70 cm)503/4" (127.6 cm)
cDepth (cutout)24" (61.0 cm)24" (61.0 cm)24" (61.0 cm)
dTop of Cutout to Bottom of Upper Cabinet DoorN/A11/2" (3.8 cm)11/2" (3.8 cm)
eBottom of Cutout to Floor (recommended)*51/4" (13.3 cm)32" (81.3 cm)143/4" (37.5 cm)*
fBottom of Cutout to Top of Cabinet DoorN/A11/2" (3.8 cm)11/2" (3.8 cm)
gOverlap of oven with sides of cutout111/16" (1.7 cm)111/16" (1.7 cm)111/16" (1.7 cm)

* Bottom of Cutout to Floor (acceptable) 4" to 143/4" (10.2 cm to 37.5 cm)

Electrical Requirements

If codes permit and a separate ground wire is used, it is recommended that a qualified electrical installer determine that the ground path is adequate and wire gauge is in accordance with local codes. Do not use an extension cord.

In U.S.A.: Be sure that the electrical connection and wire size are adequate and in conformance with the National Electrical Code, ANSI/ NFPA No. 70-latest edition and all local codes and ordinances. A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

In Canada: Be sure that the electrical connection and wire size are adequate and in conformance with CSA standard C22.1, Canadian Electrical Code, Part 1 - latest edition, and all local codes and ordinances. A copy of the above code standards can be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

Electrical Connection

To properly install your oven, determine the type of electrical connection and follow the instructions provided.

DIRECT WIRE

⚠ WARNING: Electrical Shock Hazard

Disconnect power before servicing. Improper connection of aluminum house wiring and copper appliance leads can result in an electrical hazard or fire. If the home has aluminum wiring, only use connectors designed and UL listed for joining copper to aluminum and precisely follow the manufacturer's recommended procedure. Aluminum-to-Copper connections must conform with local codes.

  • For Single Oven, use 10 gauge copper or aluminum wire.
  • For Double Oven, use 8 gauge copper or aluminum wire.
  • Electrically ground oven.
  • Failure to do so could result in death, fire or electrical shock.

Be sure your appliance is properly installed and grounded by a qualified technician. Ask your dealer to recommend a qualified technician or an authorized repair service.

This oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green (or bare) ground wire twisted together.

After ensuring power is off, connect the flexible conduit from the oven to the junction box using a UL listed conduit connector. Refer to the following pages for wiring graphics and instructions. Your local codes and ordinances take precedence over these instructions. Complete electrical connections according to local codes and ordinances.

  1. Disconnect power.
  2. Remove junction box cover.
  3. Install a UL listed or CSA approved conduit connector to the junction box. [Diagram: 'a' shows UL or CSA Listed Conduit Connector]
  4. Route the flexible electrical supply conduit from the oven to the junction box through a UL listed or CSA approved conduit connector.
  5. Tighten screws on conduit connector.

3-WIRE CONNECTION (GROUNDED NEUTRAL) - U.S.A. ONLY

⚠ WARNING: Electrical Shock Hazard

Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC), mobile homes, and recreational vehicles, or in areas where local codes prohibit grounding through the neutral conductor. For such installations, see the Ungrounded Neutral graphic. Use grounding terminal or lead to ground unit. Connect neutral terminal or lead to branch circuit neutral in the usual manner. Failure to do so could result in death, fire or electrical shock.

IMPORTANT: Use the 3-wire cable from home power supply where local codes permit a 3-wire connection.

  1. Disconnect power.
  2. Connect the two black wires together using a UL listed wire connector.
  3. Connect the two neutral (white) wires and the ground (green or bare) wire (of the oven cable) using a UL listed wire connector.
  4. Connect the two red wires together using a UL listed wire connector.
  5. Install junction box cover.

[Diagram Description: Grounded Neutral wiring in a junction box with labels a-i: a: Junction Box, b: Black Wires, c: Neutral (White) Wires, d: Ground (Green or Bare) Wire, e: Cable from Oven, f: UL Listed Conduit Connector, g: Red Wires, h: UL Listed Wire Connectors, i: House Electrical Supply]

4-WIRE CONNECTION (UNGROUNDED NEUTRAL) - U.S.A. AND CANADA

IMPORTANT: Use the 4-wire cable from home power supply in the U.S. where local codes do not allow grounding through neutral, for new branch circuit installations (1996 NEC), mobile homes, recreational vehicles, new construction, and in Canada.

  1. Disconnect power.
  2. Connect the 2 black wires together using a UL listed wire connector.
  3. Connect the 2 red wires together using a UL listed wire connector.
  4. Untwist the white wire from the green (or bare) ground wire coming from the oven.
  5. Connect the 2 neutral (white) wires together using a UL listed wire connector.
  6. Connect the ground (green or bare) wire from the oven cable to the ground (green or bare) wire (in the junction box) using a UL listed wire connector.
  7. Install junction box cover.

[Diagram Description: Ungrounded Neutral wiring in a junction box with labels a-i: a: Junction Box, b: Black Wires, c: Red Wires, d: Cable from Oven, e: UL listed or CSA Approved Conduit Connector, f: Ground (Green or Bare) Wires, g: UL Listed Wire Connector, h: Neutral (White) Wires, i: House Electrical Supply]

Installation Instructions

IMPORTANT: This appliance shall be installed only by authorized persons and in accordance with the manufacturer's installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, and local water supply regulations.

STEP 1 - UNPACK THE OVEN

⚠ WARNING: Excessive Weight Hazard

Use two or more people to move and install oven. Failure to do so can result in back or other injury.

  1. Using two or more people, remove the oven and set it on cardboard to avoid floor damage. NOTE: Do not use the handle or any portion of the front frame for lifting.
  2. Remove the shipping materials and tape from the oven.
  3. Remove the hardware package from inside the bag containing literature.
  4. Remove and set aside racks and other parts from inside the oven.
  5. Move the oven on the cardboard near where it will be installed.

STEP 2 - REMOVE THE OVEN DOOR

IMPORTANT: The oven door is heavy and fragile, and the door front is glass. To avoid oven door glass breakage, use both hands, and grasp only the sides of the oven door to remove.

  1. Open the oven door.
  2. Locate the door latches in both corners of the oven door, and rotate the latches forward to the unlocked position. [Diagram Description: 'a' indicates latched, 'b' indicates unlatched]
  3. Grasp the edges of the oven door with both hands and push the oven door fully closed. Lift up and pull the oven door toward you to remove. Set the oven door(s) aside on a covered work surface.

STEP 3 - INSTALL OVEN

⚠ WARNING: Excessive Weight Hazard

Use two or more people to move and install oven. Failure to do so can result in back or other injury.

  1. Using two or more people, grasp the ceiling of the oven cavity and lift the oven onto a table or platform, aligning it with the cutout opening. NOTE: The surface must be able to support the following weight: Single Oven: 119 lbs (54 kg); Double Oven: 209 lb (95 kg).
  2. Feed the flexible electrical supply conduit from the oven to the junction box.

STEP 4 - MAKE ELECTRICAL CONNECTION

To properly install your oven, determine the type of electrical connection you will be using and follow the instructions provided for it here.

DIRECT WIRE

⚠ WARNING: Electrical Shock Hazard

Disconnect power before servicing.

Improper connection of aluminum house wiring and copper appliance leads can result in an electrical hazard or fire. If the home has aluminum wiring, only use connectors designed and UL listed for joining copper to aluminum and precisely follow the manufacturer's recommended procedure. Aluminum-to-Copper connections must conform with local codes.

  • For Single Oven, use 10 gauge copper or aluminum wire.
  • For Double Oven, use 8 gauge copper or aluminum wire.
  • Electrically ground oven.
  • Failure to do so could result in death, fire or electrical shock.

Be sure your appliance is properly installed and grounded by a qualified technician. Ask your dealer to recommend a qualified technician or an authorized repair service.

This oven is manufactured with a neutral (white) power supply wire and a cabinet-connected green (or bare) ground wire twisted together.

After making sure that the power has been turned off, connect the flexible conduit from the oven to the junction box using a UL listed conduit connector. Refer to the following pages for wiring graphics and instructions. Your local codes and ordinances, of course, take precedence over these instructions. Complete electrical connections according to local codes and ordinances.

  1. Disconnect power.
  2. Remove junction box cover.
  3. Install a UL listed or CSA approved conduit connector to the junction box. [Diagram: 'a' shows UL or CSA Listed Conduit Connector]
  4. Route the flexible electrical supply conduit from the oven to the junction box through a UL listed or CSA approved conduit connector.
  5. Tighten screws on conduit connector.

3-WIRE CONNECTION (GROUNDED NEUTRAL) - U.S.A. ONLY

⚠ WARNING: Electrical Shock Hazard

Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC); mobile homes; and recreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor. For installations where grounding through the neutral conductor is prohibited, see the Ungrounded Neutral graphic. Use grounding terminal or lead to ground unit. Connect neutral terminal or lead to branch circuit neutral in usual manner. Failure to do so could result in death, fire or electrical shock.

IMPORTANT: Use the 3-wire cable from home power supply where local codes permit a 3-wire connection.

  1. Disconnect power.
  2. Connect the two black wires together using a UL listed wire connector.
  3. Connect the two neutral (white) wires and the ground (green or bare) wire (of the oven cable) using a UL listed wire connector.
  4. Connect the two red wires together using a UL listed wire connector.
  5. Install junction box cover.

[Diagram Description: Grounded Neutral wiring in a junction box with labels a-i: a: Junction Box, b: Black Wires, c: Neutral (White) Wires, d: Ground (Green or Bare) Wire, e: Cable from Oven, f: UL Listed Conduit Connector, g: Red Wires, h: UL Listed Wire Connectors, i: House Electrical Supply]

4-WIRE CONNECTION (UNGROUNDED NEUTRAL) - U.S.A. AND CANADA

IMPORTANT: Use the 4-wire cable from home power supply in the U.S. where local codes do not allow grounding through neutral, New Branch circuit installations (1996 NEC), mobile homes and recreational vehicles, new construction and in Canada.

  1. Disconnect power.
  2. Connect the 2 black wires together using a UL listed wire connector.
  3. Connect the 2 red wires together using a UL listed wire connector.
  4. Untwist white wire from green (or bare) ground wire coming from the oven.
  5. Connect the 2 neutral (white) wires together using a UL listed wire connector.
  6. Connect the ground (green or bare) wire from the oven cable to the ground (green or bare) wire (in the junction box) using a UL listed wire connector.
  7. Install junction box cover.

[Diagram Description: Ungrounded Neutral wiring in a junction box with labels a-i: a: Junction Box, b: Black Wires, c: Red Wires, d: Cable from Oven, e: UL listed or CSA Approved Conduit Connector, f: Ground (Green or Bare) Wires, g: UL Listed Wire Connector, h: Neutral (White) Wires, i: House Electrical Supply]

STEP 5 - MOUNT THE OVEN

  1. Slide the oven completely into the cabinet until the back surface of the front frame touches the front wall of the cabinet. Center the oven within the cabinet cutout. NOTE: Push against the seal area of the oven front frame when pushing the oven into the cabinet. Do not push against the outside edges. [Diagram Description: Shows mounting frame 'a' and mounting frame hole 'b']
  2. There are two holes, one on each side of the front frame that surrounds the oven cavity. Drill 1/8" (3.18 mm) pilot holes through these holes, and into the front wall of the cabinet. NOTE: The double oven has four mounting holes, two on each side.
  3. Insert the #8-14 x 1" screws (provided) through the pilot holes to securely fasten the oven to the cabinet. Do not overtighten screws.
  4. Replace the oven racks.
  5. Reconnect power to the oven.

STEP 6 - REPLACE THE DOOR

IMPORTANT: The oven door is heavy and fragile, and the door front is glass. To avoid oven door glass breakage, use both hands, and grasp only the sides of the oven door to remove.

  1. Verify that the door hinge latches are forward, and then insert the oven door hinges into the openings.
  2. Lower the oven door to engage the hinges.
  3. Press the hinge latches down to lock.

STEP 7 - COMPLETE INSTALLATION

  1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.
  2. Dispose of/recycle all packaging materials.
  3. Check Operation of Oven:
    • Turn on power.
    • Press BROIL.
    • Set the temperature.
    • Press START.
    NOTE: If oven(s) does not operate, check the following:
    • Household fuse is intact and tight; or circuit breaker has not tripped.
    • Electrical supply is connected.
    • See "Troubleshooting" section in the User Manual.
  4. When oven has been on for 5 minutes, feel for heat. If you do not feel heat or if an error message appears in the display, turn off the oven and contact a qualified technician.
  5. Press CANCEL to turn off the oven.

Customer Support

FOR FAST SUPPORT

EMAIL AT INFO@FORNO.CA

Customer Support: Call 1-866-231-8893 or email: info@forno.ca

Models: FBOEL1370-30BLK, FBOEL1324-30BLK, FBOEL1370-30BLK FBOEL1324-30BLK 30 inch Single Double Wall Oven-Mechanical Control, FBOEL1370-30BLK FBOEL1324-30BLK, 30 inch Single Double Wall Oven-Mechanical Control, Single Double Wall Oven-Mechanical Control, Wall Oven-Mechanical Control, Oven-Mechanical Control, Control

File Info : application/pdf, 17 Pages, 8.26MB

PDF preview unavailable. Download the PDF instead.

frddoxpqzkxr Adobe Illustrator(R) 24.0 (C) 2018 Retailer Web Services LLC, all rights reserved.

Related Documents

Preview FORNO Espresso 30" Wall Oven Installation Guide: FBOEL1370-30WHT, FBOEL1324-30WHT
Comprehensive installation guide for FORNO Espresso 30" Single and Double Wall Ovens (Models FBOEL1370-30WHT, FBOEL1324-30WHT). Covers safety, requirements, electrical connections, mounting, and final checks.
Preview Guide d'Installation Four Mural et Double Paroi FORNO Espresso
Instructions détaillées pour l'installation des fours muraux et doubles FORNO Espresso, incluant sécurité, exigences électriques, dimensions et étapes de montage. Modèles FBOEL1370-30BLK et FBOEL1324-30BLK.
Preview Forno Gallico Single and Double Wall Oven Instruction and Installation Guide
Comprehensive instruction and installation guide for Forno Gallico single and double electric wall ovens, including safety precautions, product details, and installation steps.
Preview 30" Wall Oven Installation Guide
Installation dimensions and specifications for 30-inch single and double wall ovens.
Preview Forno Gallico 30" Double Built-in Electric Wall Oven - Dimensions and Cutout Guide
Detailed product dimensions and cutout specifications for the Forno Gallico 30-inch double built-in electric wall oven with French doors and chef door, model FBOEL1388-30. Includes product dimensions, cutout dimensions, and installation notes.
Preview FORNO Espresso Electric Range Instruction Manual
Comprehensive instruction manual for the FORNO Espresso Electric Range, covering operation, safety, and care for models FFSEL6012-30, FFSEL6012-30BLK, and FFSEL6012-30WHT.
Preview Forno Aria 30 Inch Wall-Mounted Range Hood with 600 CFM Motor, 4-Speed Fan
Detailed specifications for the Forno Aria 30-inch wall-mounted range hood, featuring a 600 CFM motor, 4-speed fan, LED lighting, and a 2-year warranty. Includes information on appearance, dimensions, weight, technical specifications, and venting performance.
Preview FORNO Massimo 30-inch 5-Burner Gas Range with Air Fryer - FFSGS6239-30BLK
Detailed specifications for the FORNO Massimo 30-inch black gas range (Model FFSGS6239-30BLK), featuring 5 burners, 68,000 BTU total output, 4.32 cu ft convection oven, air fryer, and professional design.