Phanteks Eclipse G500A Installation Guide
Thank you for choosing Phanteks. This manual will guide you through the installation process of the Eclipse G500A chassis. If you have any questions, please contact Phanteks through their customer service or social media.
Phanteks will not take responsibility for any damages incurred due to incorrect installation or usage of this product.
Models Covered: PH-EC500GA_DBK01A (D-RGB Satin Black), PH-EC500GA_DMW01A (D-RGB Matte White), PH-EC500GA_BBK01 (Performance), PH-EC500GA_DBK01B (D-RGB Fanless).
Panel Removal
It is recommended to remove all external panels before starting the installation process. The G500A comes with storage cover panels that are behind the right side panel, these support up to 6x 2.5" SSDs next to the 3x 2.5" SSD pre-installed brackets.
- Left Side Panel: Lift upwards to remove.
- Right Side Panel: Lift upwards to remove.
- Cover Panels: Push down the clips on each cover panel to release and remove.
Front Panel & Dust Filters
- Front Panel: Grab and pull towards you from below to remove.
- Top Filter: Pull upwards at the rear to remove.
- PSU Filter: Slide outwards to remove.
Front Fan Brackets
The front fan brackets can be secured in the 120mm fan position using 6x screws. Out of the box, the brackets are set to the 140mm position.
Hardware Installation
Motherboard
Install the ATX motherboard using 9x motherboard screws. For M-ATX Motherboards, follow the motherboard instructions to move the stand-offs to the correct position. Use the 'stand-off removal tool' when using a smaller motherboard.
Power Supply
- Remove the PSU bracket by loosening 2x thumb screws.
- Install the power supply onto the bracket using 4x PSU screws.
- Place the bracket back into the chassis and tighten the 2x thumb screws.
Pro Tip: Connect all needed cables to the power supply first for easier installation.
Storage Installation
2.5" SSD
- Secure SSDs with 4x SSD screws directly onto the panels.
- Slide the SSD Bracket up to remove it from the chassis. Secure the SSD with 4x SSD screws to the SSD Bracket.
- For even more storage, secure the SSD with 4x SSD screws to the SSD Bracket.
- Note: SSD Cap removal is for the white model only.
3.5" HDD
- Remove the HDD thumb screw to remove the cable cover(s) on the inside of the chassis.
- Slide the 3.5" HDD into the HDD cage. When installing 2x 3.5" HDD brackets, stack them first before placing them into the chassis.
- Slide the HDD bracket into the bottom part of the chassis, ensure they click when installed.
- Pro Tip: The HDD tray can also hold a 2.5" SSD.
- To lock the HDD bracket, use 2x thumb screws.
Cables
Connect the front I/O cables to the motherboard and power supply. Refer to the motherboard manual for specific header locations.
- Front I/O: POWER_SW, POWER, HD AUDIO, USB 3.0, USB C 3.1
- Motherboard Headers: Ensure correct connection for power switch, reset switch, HDD LED, etc.
D-RGB Controls
Applicable Models: PH-EC500GA_DBK01A, PH-EC500GA_DMW01A & PH-EC500GA_DBK01B
The D-RGB controller allows for multiple lighting effects and colors. More D-RGB lighting products can be connected to the integrated D-RGB controller. Optionally, lighting can be connected and controlled via motherboard software.
- Modes: SOLID, BREATHING, SPARKLE, MULTI-COLOR
- Colors: Adjust colors from a wide spectrum.
- Turn Off LEDs: Press and hold the MODE button for two seconds to turn off LEDs, press again to turn it ON.
Note: D-RGB control buttons are deactivated when connected to a motherboard.
Anti-Sag Bracket
Make sure to install all GPU & PCI cards beforehand. Place the GPU anti-sag bracket at the back. For easy access, remove the SSD bracket first.
- Insert the thumbscrews without tightening them.
- Manually press down the screws (1), then lock the thumbscrews in position (2).
Included Vertical GPU Mount
The G500A chassis supports the placement of a vertical GPU with the included vertical GPU mount. The Vertical GPU mount has two mounting positions, A or B.
- Position A: Can hold 3-slot GPU cards.
- Position B: Can hold 2-slot GPU cards.
- Connect the riser cable to the vertical GPU mount and secure it with 2x long riser cable screws.
- Secure the Vertical GPU mount on the chassis with 2x PSU screws.
Note: Gen 4 Riser Cable sold separately (PH-CBRS4.0_FL22).
Optional Upgrade: Gen 4 Vertical GPU Bracket
As an alternative, the G500A supports the Phanteks Vertical GPU Bracket (PH-VGPUKT4.0_03) which supports up to a 4-slot GPU. This bracket also positions the GPU further away from the tempered glass panel for increased airflow.
Fan & Radiator Support
Fans
- Front: 3x 120mm or 3x 140mm
- Top: 3x 120mm or 3x 140mm
- Rear: 1x 120mm or 1x 140mm
Radiator
- Front: Up to 360mm (120mm) or up to 420mm (140mm)
- Top: Up to 360mm (120mm) or up to 280mm (140mm)
- Rear: Up to 120mm
Clearance
- CPU Cooler Height: 185 mm
- GPU Length: 435 mm
- Power Supply Length: 250 mm (195mm if all 4 bottom HDD positions used)
- Front Panel Fan: 33 mm (Behind front panel)
- Top Radiator Clearance: 70 mm
- Front Radiator Clearance: 95 mm
Included Accessories
- 22x SSD + Motherboard Screw
- 7x PSU Screw
- 8x HDD Locking Screw
- 12x Thumb Screw
- 8x Fan Screw
- 6x Case Screw
- 3x Motherboard Stand-off
- 1x Standoff Removal Tool
- 1x Anti-Sag Bracket
- 1x Vertical GPU Mount
- 6x Zip Tie
One moment, please...
