User Manual for Rayrun models including: TT40 Smart and Remote Control RGB W LED Controller, TT40, Smart and Remote Control RGB W LED Controller, Remote Control RGB W LED Controller, Control RGB W LED Controller, RGB W LED Controller, LED LED Controller, LED Controller
Tuya Series RGB White Controller
Smart & Remote Control
RGB+W LED Controller
Model: TT40 (W/Z/B)
Tuya Smart
Wireless Remote
Overheat Protection High Power
Compact Size
12V/24V voltage
Introduction
TT40 LED controller is designed to drive constant voltage RGB+White color LED products in voltage range of DC12-24V. It can be controlled by smart phone with Tuya smart app connection or by the stand alone RF remote controller. User can setup LED brightness, color, scene and dynamic effects with the rich function on smart phone Tuya app or the easy operation remote controller.
Terminal & Size
60mm
20.5mm
1
3
2
1. Power supply input
Connect positive power to the cable marked with `+' and negative to the cable marked with `-'. The controller can accept DC power from 12V to 24V, the output is PWM driving signal with same voltage level as the power supply, so please make sure the LED rated voltage is same as the power supply.
2. LED output
Connect to constant voltage type LED load. Connect the LED to black cable, and R, G, B, W cable to the relevant color . Please make sure the LED rated voltage is same as the power supply and the maximum load current is below the controller rated current.
CAUTION! The controller will be permanently damaged if output cables short circuited. Please ensure the cables are well insulated to each other.
3. Work status indicator (optional) This indicator shows all working status of the
controller. It displays different events as following: Steady on: Remote and Tuya smart mode. Flash twice: Tuya not connected. Flash 3 times: Over heat protection. Blink: New command received. Long single blink: Brightness or speed reach limit.
4. Wiring diagram
To 110/230 12-24V DC output AC power Power supply
TT40 LED Controller
LED Strips
12-24V DC LED Controller 12-24V Driving
2
Functions
5 6
10
8
EFFECT EFFECT
12
9
Pair new remote
7
Press in 10
11
seconds once receiver powered
Reset to factory
5. Turn ON / OFF Press `I' key to turn on unit or press `O' key to turn off.
The power on status can be set to last status or default status from app. At last status mode, the controller will memorize the on/off status and will restore to the previous status on next power on.
6. Light mode switch Press this key to switch between RGB, white and
RGB+White mode. In RGB mode, white channel will be disabled; In white mode, RGB channel will be disabled; In RGB+White mode, all channels are usable.
7. Select static RGB color Press and key to select color from the
preset library colors.
8. Shortcut color select Shortcut key to static colors. LED will run the
relevant color when pressing the specific color key. The shortcut color is included in and content.
9. White brightness control Press key to increase white LED brightness and
press key to decrease.
10. RGB brightness control Press key to increase RGB LED brightness and
press key to decrease.
11. RGB dynamic effect Control the RGB dynamic effects. Press EFFECT and EFFECT
to select dynamic effects and press and key to set the running speed of the dynamic effects.
12. Remote indicator This indicator blinks when remote controller working.
Please check the remote battery if the indicator does not light up or flash slowly. The battery type is CR2032.
Operation
13. Using the remote controller
Please pull out the battery insulate tape before using. The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts.
14. Setup Tuya connection
Please install the Tuya app to setup the connection. Before setup, please make sure the controller is at factory default mode and not connected to any gateway or router.
15. Pair a new remote controller
The remote controller and receiver is 1 to 1 paired as factory default. It's possible to pair maximum 5 remote controllers to one receiver and each remote controller can be paired to any receivers.
To pair a new remote controller, please follow two steps:
1). Plug off the power of the controller and plug in again after more than 5 seconds.
2). Within 10 seconds after controller powered on,
press and
key simultaneously for about 3
seconds.
After this operation, the LED lights will flash 3 times to acknowledge that remote pairing is accomplished.
16. Reset to factory default
To reset the controller's Tuya setting and unpair all remote controllers, please operate with following two steps:
1). Plug off the power of controller and plug in again after more than 5 seconds.
2). Press and key simultaneously for about 3 seconds, within 10 seconds after the receiver powered on.
After this operation, the controller will be reset to factory default, the Tuya configuration and remote pairing will all be reset.
Overheat Protection
The controller has overheat protection feature and it can protect itself from damage caused by some abnormal usage such as overloading which generates excess heat. At overheat situation, the controller will shutdown the output for a short while and recover when temperature drops to a safe range.
Please check the output current and make sure it's under rated level at this situation.
Specification
Model Output Mode Working voltage Rated output current Tuya connection PWM grade Overheat protection Remote frequency Remote control distance Overheat protection Controller dimension Remote dimension
TT40(W/Z/B) PWM constant voltage
DC 12-24V 4x2A
W: Wifi; Z: Zigbee; B: Bluetooth 4000 steps Yes 433.92MHz
>15m at open area Yes
60x20.5x9mm 86.5x36x8mm
7
RGB+WLED
Model: TT40 (W/Z/B)
12-24V
TT40RGB+WLED D C1 2 - 2 4 V L E D a p p L E D appLED LED
60mm
20.5mm
1
3
2
1. 1 2 V2 4 V
"+" "-" L E D
2.LED
L E D L E D LED LED
3.()
2 3
4.
12-24V
TT40 LED
12-24V DC
LED
2
5 6 10 8
EFFECT EFFECT
12 9
7
11 10
5. "I " "O "
a p p
6. RGB
R G B R G B RGB RGBRGB R G B
7.RGB
8. LED
9.
R G B R G B 11.RGB
EFFECTEFFECT R G B R G B
12.
CR2032
13. R F
14.app
a p p
15. 11 1
5
1 5 210 3 L E D
16.
1 5 210
3
PWM
TT40(-W/Z/B) PWM DC12-24V 3x3A
W:Wifi;Z:Zigbee;B:Bluetooth 433.92MHz
>15 4000
60x20.5x9mm 86.5x36x8mm
7
Corel PDF Engine Version 18.1.0.661 CorelDRAW X8