Husky 84-Inch 22-Drawer Mobile Workbench Use and Care Guide

Safety Information

• Do not open more than one drawer at a time.
• Keep children away from the product.
• Load the product starting with the bottom drawers to prevent tipping.
• Keep caster brakes locked unless moving the cabinet to prevent rolling.
• Lock all drawers before moving the product.
• Ensure all drawers are tightly closed before locking/unlocking.
• Do not step in any drawer.
• Push the product rather than pull it when moving.
• Do not alter this product in any manner.

Plug and Outlet Safety

WARNING: Chest/cabinet plugs must match the outlet. Never modify the plug. Do not use adapter plugs with grounded power strips. Unmodified plugs and matching outlets reduce the risk of electric shock.

WARNING: Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators, as this increases the risk of electric shock.

WARNING: Chests/cabinets marked "Grounding Required" have a three-wire cord and grounding plug. This plug must be connected to a properly grounded outlet. Grounding provides a low-resistance path to carry electricity away from the user, reducing the risk of electric shock. The green wire in the cord must be the only wire connected to the grounding system and must never be attached to an electrically "live" terminal. Your power strip must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances.

DANGER: Do not stand on this product. You may fall or cause the product to tip.

DANGER: Do not move the product prior to closing and locking all drawers. Drawers could open, making the product unstable and prone to tipping.

DANGER: Do not mount this product on a truck bed or any other moving object.

WARNING: Keep the product on a level surface. The product may become unstable and tip if stored or moved on an uneven surface.

CAUTION: Do not lift this product directly with a forklift or tow with any mechanical devices.

CAUTION: Do not exceed the maximum product weight, including contents. Do not exceed the maximum weight for each drawer. See Specifications on page 4.

CAUTION: Only transport this product when empty. Properly secure when transporting.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

CAUTION: Do not use the side handle as a point of leverage to lift the unit off the ground. The handle is not intended to withstand the force of vertical lifting and is only designed to aid in the movement of the unit around on casters. Failure to adhere to this warning may cause the handle to break and result in personal injury and/or product damage.

Responsible Party: Clearwater Metal Vn JSC, Lot CN2, Mai Trung IZ, An Tay Village, Ben Cat Town, Binh Duong Province, Vietnam. Tel: +84.274.3581.773

Product Name: Power strip 6 outlets with 2 USB ports

Model#: K2415009 / K2415014 / K2415021

Warranty

The manufacturer warrants the product to be free from defects in materials and workmanship for a period of five (5) years from the date of purchase. This warranty applies only to the original consumer and only to products used in normal use and service. If this product is found to be defective, the manufacturer's only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer's discretion, provided that the product has not been damaged through misuse, abuse, accident, modifications, alteration, neglect, or mishandling. This warranty shall not apply to any product that is found to have been improperly installed, set-up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the products such as surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-888-HD-HUSKY or visit www.huskytools.com.

Pre-Assembly

Tools Required

• Phillips screwdriver
• Safety goggles

Hardware Included

NOTE: Hardware not shown to actual size.

Specifications

• Maximum capacity (drawer): 120 lbs
• Maximum capacity (bottom deep drawers): 240 lbs
• Maximum capacity (total unit): 3,800 lbs

NOTE: Begin product assembly close to the final intended location of your mobile workbench. This product is heavy and may be difficult to move after assembly.

Package Contents

Assembly

1. Attaching the Side Handle

   Attach the side handle (B) to the cabinet using four bolts (BB). Tighten all bolts with the 10 mm wrench (CC). Do not over tighten the bolts to avoid damage to the finish.

   NOTE: The holes in the cabinet are tapped and do not require nuts.

2. Attaching the Power Strip Brackets

   Attach the power strip brackets (H) to the cabinet for both sides using two bolts (AA) each. Tighten all bolts using a screwdriver. Do not over tighten the bolts to avoid damage to the finish.

   NOTE: The holes in the cabinet are tapped and do not require nuts.

3. Installing the Drawer Liners

   Place the drawer liners (K) in appropriately-sized drawers to protect the surface.

Operation

1. Locking and Unlocking the Unit

   IMPORTANT: The drawers must be fully closed before locking/unlocking the unit.

   • To lock the unit, insert the key (I) into the lock (J) and turn it one quarter turn counterclockwise. Then remove the key.
   • To unlock the unit, insert the key (I) into the lock (J) and turn it one quarter turn clockwise. Then remove the key.

2. Removing the Drawers

   Fully extend and empty the drawer. On the slide, lift up the plastic release lever on one slide and push down the plastic release lever on the other slide. Gently pull the drawer out so the slides can ride over the stops.

3. Installing the Drawers

   Pull the slides and slide carrier out until fully extended. Hold the slide on the cabinet while aligning it with the slide on the drawer. Slightly insert one side and repeat for the other side. Slowly push the drawer until it is fully closed to engage the slide. Open the drawer and close it to verify proper operation.

Maintenance

1. Maintaining the Casters

   Grease the casters annually using high-quality bearing grease.

2. Maintaining the Drawers

   Periodically clean the drawer trim and inside the drawers with a mild detergent and water. Remove grease and oil with a standard, nonflammable cleaning fluid. The use of drawer liners is recommended to protect the finish inside the drawers and make them easier to clean. Drawer liners can be purchased at The Home Depot. Lubricate the slides semi-annually with grease or equivalent.

Care and Cleaning

This steel product has been coated with industrial powder coating for a durable finish. To help protect this finish, do not allow harsh chemicals such as oil or grease to remain on the powder coating surface. Use a glass cleaner (Windex® or equivalent product) to clean and maintain all powder coated surfaces.

Service Parts