KuKirin G3 Pro User Manual

Catalog

• 1. Product & Accessories
• 2. Function Introduction
• 3. Safety Instruction
• 4. Product Display
• 5. Scooter Assembly
• 6. Expand Steps
• 7. Fold Steps
• 8. Charging
• 9. Transportation
• 10. Button Function
• 11. Password Modification Method
• 12. Basic Operation
• 13. Operate Instruction
• 14. Ride Instruction
• 15. Battery & Charger
• 16. LED Display
• 17. Maintenance
• 18. Normal Problem and Solution
• 19. Parameter Setting
• 20. After-Sale Service
• 21. Product Warranty
• 22. Warranty Card

1. Product & Accessories

The box includes: User manual, Inflator, Tool bag & screws, Charger.

Please carefully check whether the items in the box are complete and intact. If there is any missing or damaged, please contact the seller.

2. Function Introduction

The KuKirin G3 Pro scooter features:

• Instrument
• Hook
• Stud
• Fold handlebar
• Headlight
• Front fender
• Lithium battery
• Silicone pedal leather
• Rear fender
• Motor
• Kickstand

3. Safety Instruction

Note: Please read the following important safety information carefully before use and follow it.

• This electric scooter is for adult use only; do not carry others at the same time.
• When riding the electric scooter, please wear a helmet and other protective gear.
• Do not ride this product in an unsafe or illegal location.
• Please practice in an open space first, and then ride on the road after you are proficient in the operation.
• Do not perform dangerous actions or ride with one hand while the scooter is running, and keep both feet on the pedals.
• Do not attempt to go directly through steps with a gap of more than 30cm, which may cause the scooter to overturn. Avoid injury to the driver or damage to the scooter.
• For your driving safety, please control the speed within 25KM/H. Please try to avoid riding at night. If you ride at night, please turn on the lights and control the speed to 15KM/h or below.
• Do not use this product in an environment below -5 degrees Celsius.
• In case of uneven road surface or poor road conditions, please slow down and drive carefully or get off the vehicle.
• Do not ride this product on slippery roads (such as water, ice, oil, etc.).
• Do not immerse the product in water deeper than 4CM to avoid damage to the electrical parts of the vehicle due to water ingress.
• In bad weather such as rain, snow, and strong wind, please try to avoid riding to avoid unnecessary personal injury.
• The user should use the product in accordance with the relevant instructions in the product manual and should not exceed the load that the product can bear (120kg).
• Please avoid using or placing the product in a high or low temperature environment. Do not place this product together with flammable items to avoid fire in extremely accidental circumstances.
• The electric scooter is a special riding product. Please try to ride on a smooth road with no potholes.
• Users should ride in strict accordance with traffic laws and regulations. If there are special local laws and regulations, they should ride legally in accordance with local laws and regulations.

4. Product Display

The scooter can be in an expanded state or a folded state.

5. Scooter Assembly

1. Unfold the scooter and open the parking bracket to unfold the scooter (refer to 6 unfolding steps).
2. Straighten the body bar and apply force forward.
3. Confirm that the spring pin is back in place, and turn the handle to the right to tighten.
4. Use the tools included in the package to tighten the screws, and check if the power switch is working properly after assembly is complete.

6. Expand Steps

1. Press down on the hook with one hand and pull up the body bar with the other.
2. Pull the body bar up.
3. Straighten the body bar and apply force forward.
4. Confirm that the spring pin is back in place and turn the handle to the right to tighten.

7. Fold Steps

1. Holding the pole in hand, turn the handle to the left (counterclockwise).
2. Hold the pole with one hand and pull the spring pin outward with the other.
3. Put lower body bar.
4. Adjust the body bars to make sure the hooks fit into the slots and snap into place.

8. Charging

1. Open the charging port waterproof plug and insert the charger connector into the charging hole on the body.
2. Insert the charger power plug into a power outlet.
3. When the indicator light of the charger is red, it means charging, and when the indicator light of the charger turns green, it means that the battery is fully charged. Fasten the waterproof plug.

When folded, you can carry the scooter with one or two hands.

10. Button Function

1. Insert the key, turn the key to the right to power on.
2. Press and hold the function switch button to switch the machine on and off.
3. Short press the function switch button once after power on to switch gears, divided into three gears.
4. Short press the single-drive switch once after power on to switch between single-drive and dual-drive modes.
5. After power on, press the function switch button three times in a row to enter the menu setting interface. The meter will display P1, P2, P3, P4, P6, P7, P8, Pa, Pb, Pc.

Parameter Settings:

• P1: km/mile selection setting (default km).
• P2: Voltage level setting (36V/48V/52V/60V/72V).
• P3: Wheel diameter (unit: inch; can be set to 080-160, e.g., 080 means 8 inches, 100 means 10 inches, etc., increasing by 5 each time).
• P4: Number of magnetic poles for speed measurement (range: 1-100, default 30).
• P5: Cruise selection (0 means no cruise; 1 means cruise). When the cruise is not turned on, the cruise icon does not light up; when the cruise is turned on, the cruise icon flashes. After 8 seconds of entering cruise, the cruise icon flashes. The default is not to cruise.
• P6: Zero startup, non-zero startup settings (0: zero startup; 1: non-zero startup). The startup mode will be displayed when starting up (zero startup will not display an icon, non-zero startup will display NON). The accelerator starts directly. In non-zero start mode, you need to slide the scooter over 5KM/h and press the accelerator to start.
• P7: Speed limit setting (range 0-100 percent speed limit).
• P8: Sleep time setting (0: no sleep; other numbers are sleep time, range: 1-60 minutes, default 5 minutes).
• PA: Start strength setting (1-5, 1 minimum, 5 maximum).
• PB: Brake strength setting (1-5, 1--20%, 2-35%, 3-50%, 4-70%, 5-100%).

When P1 is displayed, 0-km or 1-mile will be displayed below, indicating the optional setting of km/mile. Long press the power button for 3 seconds, the value will flash. At this time, short press the power button to select 1-mile or 0-km. When 0-km is displayed, select km, and Km/h will be displayed. When 1-mile is displayed, select mile, and mile will be displayed. Then long press the power button to exit. To select other parameters for debugging, if there is no operation for 8 seconds, it will automatically exit the parameter setting. If the current parameter does not need to be modified, press the button once to switch to the next parameter setting interface.

11. Password Modification Method

1. Original password is 000. Align the tick marks.
2. Press the hole with a pointed object, then modify the password you want to set, and then release it. The password setting is completed.

12. Basic Operation

Components:

• A. Power button
• B. Single & double driver switch
• C. Throttle
• D. Handlebar cover
• E. Instrument
• F. Brake
• G. Headlight switch
• H. Side light switch
• I. Horn
• J. Function switch button

13. Operate Instruction

Turn On and Turn Off

Insert the key, turn the key to the right to power on. Press and hold the function switch button for 3 seconds to turn on the vehicle. Long press the function switch button for 3 seconds to turn the key to the left to turn off the vehicle.

Gear Setting

Press the function change button once; the setting range is 1st gear, 2nd gear, and 3rd gear.

Brake Control

The greater the pressure on the brake lever, the greater the braking force.

LED Headlight Switch

In the power-on state, push the headlight switch key up to turn on the headlights.

Emergency Brake

When encountering an emergency, use your fingers to hold the brake lever tightly. At this time, the rear wheel friction braking can be realized at the same time. Under normal circumstances, please do not use the emergency brake after vigorously driving at high speed, so as to avoid damage. The company is not responsible for the damage caused by riding risk or damage to the rear wheel, and it needs to be repaired at a fee.

Cruise Control

When entering the cruise control mode, repress the throttle or press the brake to withdraw from cruise control. If you need to turn off the cruise mode, enter the menu setting interface and set P5 to 0.

14. Ride Instruction

Ride Preparation

1. Choose a venue suitable for riding.
2. Unfold the product according to the unfolding instructions and wear protective gear.

Begin to Ride

1. Insert the key, turn the key to the right to power on, long press the function switch button for 3 seconds to turn on the scooter.
2. Place one foot on the pedal and the other on the ground.
3. After turning on, under the zero start mode, press the throttle to turn on directly. Under the non-zero start mode, slide the scooter over 5KM/H and then press the throttle to turn on. Slowly press the accelerator, and the scooter will move forward slowly. After driving smoothly, place the other foot on the ground at the same time and press the right thumb accelerator. The larger the angle, the faster the speed of the scooter.

Stop

Under normal circumstances, hold the brake lever tightly. The scooter will immediately power off and brake. The greater the depression angle, the greater the braking force.

15. Battery & Charger

Every KuKirin G3 Pro electric scooter is equipped with dedicated lithium batteries and dedicated smart chargers. Each scooter and its accessories have a special number. Please do not use other chargers to charge, and do not charge other types of products with the company's chargers. The company is not responsible for any damage to the battery or charger caused by this.

Battery

The lithium battery provided by KuKirin can be recharged within 600 times without any change in capacity. More than 600 times, the capacity will slowly drop to 80%. Normal use can generally reach more than 1000 times. The lithium battery may be dangerous when charging, please charge it outdoors.

Charger

The special chargers provided by KugooKirin have a charging protection function. When the battery is 100% full, it will automatically power off. The charging time of the 2A charger is about 10 hours, the charging time of the 3A charger is about 7 hours, and the charging time of the 5A charger is about 4 hours. Damage to the battery due to abnormal factors such as water, collision, etc., is not covered by the warranty policy.

16. LED Display

The LED display shows information such as:

• Turn left/right indicators
• Brake mark
• Speed
• Non-zero start / Single drive / Double drive indicators
• Power indicator
• Headlight mark
• Mode
• Gear
• Mileage/Error-code
• Cruise control

17. Maintenance

Lubricant

Every six months, add a small amount of white grease or lubricant to the folded part for maintenance. Please check the scooter every three months to see if there are any loose screws. If they are loose, please tighten them.

Battery

When you get the electric scooter for the first time, please fully charge the battery before using it. The battery can be charged at any time to ensure that the battery has electricity. During this period, charging will not cause any damage to the battery. When the battery is not in use, please charge it once every 3 months.

Store and Daily Care

Please do not leave the scooter in the hot sun or other severely damp places for a long time. Please keep the scooter surface clean.

18. Normal Problem and Solution

• Unable to turn on: The battery may be dead. Plug it into the charger to charge it, and then press the operation to turn it on and try again.
• Brakes are loose: The brake fluid may not be enough. Add the brake fluid and try again.
• Fault code on the meter: Refer to the manual for troubleshooting.

19. Parameter Setting

20. After-Sales Service

Warranty Statement

This product is within the warranty period from the time of your purchase. Under normal use, if the product is faulty and damaged due to quality problems, KuKirin will repair, replace, or return it for you free of charge as the case may be. The warranty period starts from the first purchase of the product and is subject to the date of the invoice receipt. When applying for after-sale service, you need to provide an accurate, complete, and clearly filled valid sales invoice.

Exclusions from Warranty:

• Misuse, abuse, or improper transportation, maintenance, or storage, including use, storage, or conservation under inappropriate temperature, humidity, or other inappropriate environmental conditions.
• Force majeure or unexpected events and other non-human controllable events.
• Repair or dismantling by non-authorized personnel of the company without authorization.
• Third-party products or services.
• Use of the product for a purpose other than the specified or intended purpose.
• Use in other ways that violate the product's instructions for use.
• Use of the product for commercial purposes.
• Accumulated mileage of the vehicle body record exceeding 2,000 kilometers.
• Normal wear or aging, scratches, problems caused by the use of paints, solvents, or chemicals during product use are not covered by the warranty.
• The original identification label of the product has been altered or damaged.
• The integrity and completeness of the product and accompanying materials.

The above are all guarantees made on KuKirin products. This warranty gives you specific legal rights, and you may also have other rights under the law. Nothing in this document affects your consumer rights that cannot be excluded or limited under the law.

21. Product Warranty

Note: Consumables such as tire casing, headlight assembly, instrument cover, handle cover, fender, rear tail light, decorative cover, foot stand, charging port seat, rubber plug, and on-board tool kit are not covered by the warranty policy.