10 X 330MM AIR BELT SANDER

1. SAFETY

WARNING!

• ✔️ WARNING! Disconnect from air supply before changing accessories or servicing.
• ✔️ Maintain the sander in good condition (use an authorised service agent).
• ✔️ Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
• ✔️ Use in suitable clean and tidy working area, free from unrelated materials and ensure there is adequate lighting.
• ✔️ Before each use check abrasive belt for condition. If worn or damaged replace immediately.
• ✔️ Use only the correct size and type of sanding belt with this sander.
• ✔️ Ensure there are no flammable or combustible materials near the work area.

WARNING!

• ✔️ Use face, dust, or respiratory protection in accordance with COSHH regulations.
• ✔️ Depending on the task, sander noise level may exceed 85dB, in which case wear safety ear defenders.
• ✔️ Remove ill fitting clothing. Remove ties, watches, rings, other loose jewellery and contain and/or tie back long hair.
• ✔️ Wear appropriate protective clothing and keep hands and body clear of working parts.
• ✔️ Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
• ✔️ Keep children and unauthorised persons away from the work area.
• ✔️ Check moving parts alignment on a regular basis.
• ✔️ Ensure work piece is secure before operating the sander. Never hold a work piece by hand.
• ✔️ Check the work piece to ensure there are no protruding screws, bolts, nuts, nails, rivets, etc.
• ✔️ Avoid unintentional starting.

WARNING!

• ✔️ Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are secure.
• ✔️ Prolonged exposure to vibration from this sander poses a health risk. It is the owner's responsibility to correctly assess the potential hazard and issue guidelines for safe periods of use and offer suitable protective equipment.

• ❌ DO NOT use the sander for a task it is not designed to perform.
• ✔️ DO NOT operate sander if any parts are damaged or missing as this may cause failure and/or personal injury.

WARNING!

• ❌ DO NOT carry the sander by the hose, or yank the hose from the air supply.
• ❌ DO NOT force, or apply heavy pressure to, the sander, let the sander do the work.
• ❌ DO NOT switch the sander on whilst the belt is in contact with the work piece.
• ❌ DO NOT operate sander when you are tired or under the influence of alcohol, drugs or intoxicating medication.
• ❌ DO NOT use sander where there are flammable liquids, solids or gases such as paint solvents and including waste wiping or cleaning rags etc.
• ❌ DO NOT carry the sander with your finger on the power lever.
• ❌ DO NOT direct air from the air hose at yourself or others.
• ✔️ When not in use disconnect from air supply and store in a safe, dry, childproof location.

WARNING! LEAD PAINT

Paint once contained lead as a traditional ingredient. The dust from the removal of such paint is toxic if ingested/inhaled and must be avoided. The following actions must be taken before using the sander on a surface that you suspect may contain lead paint.

1. User must determine potential hazard relating to age of paint to be removed (Modern paints do not have lead content).
2. DANGER! Keep all persons and pets away from the work area. The following persons are particularly vulnerable to the effects of lead paint dust: Expectant women, babies and children.
3. We recommend personal protection by using the following safety items:
   • Paint Spray Respirator (Sealey ref. SSP1699)
   • PE Coated Hooded Coverall (Sealey ref. SSP265-L).
   • Latex Gloves (Sealey ref.SSP24).
4. Take adequate measures to contain the paint dust, flakes and scrapings.
5. Continue to wear safety equipment as in (3) above and thoroughly clean all areas when task is complete. Ensure paint waste is disposed of in sealed bags or containers and according to local Authority guidelines.

2. INTRODUCTION

The SA35 Belt Sander features an articulated sanding arm, belt tracking control, heavy-duty nose roller and one handed trigger operation. Suitable for sanding areas with limited access.

3. SPECIFICATION

• Belt: 10 x 330mm
• Air Pressure: 90psi
• Air Consumption: 7cfm
• Air Inlet: 1/4"BSP
• Noise Power/Pressure: 97/86dBA
• Vibration: 0.52m²
• Uncertainty: 0.55m²

4. PREPARING FOR USE

4.1. AIR SUPPLY (RECOMMENDED HOOK-UP PROCEDURE IS SHOWN IN FIG.1)

• Ensure the sander air valve (or throttle) is in the "off" position before connecting to the air supply.
• You will require an air pressure between 70-90psi, and an air flow of 7cfm.
• WARNING! Ensure the air supply is clean and does not exceed 90psi. Too high an air pressure and unclean air will shorten the product life due to excessive wear, and may be dangerous causing damage and/or personal injury.
• Drain the air tank daily. Water in the air line will damage the sander and will invalidate your warranty.
• Clean compressor air inlet filter weekly.
• Line pressure should be increased to compensate for unusually long air hoses (over 8 metres). The minimum hose size should be 1/4" I.D. and fittings must have the same inside dimensions.
• Keep hoses away from heat, oil and sharp edges. Check hoses for wear, and make certain that all connections are secure.

4.2. COUPLINGS

Vibration may cause failure if a quick change coupling is connected directly to the air sander. To overcome this, connect a leader hose to the sander. A quick change coupling may then be used to connect the leader hose to the air line recoil hose. See figs.1 & 2.

Figure 1: Air Supply Hook-up Diagram Description: Shows the components of an air supply system. From the 'AIR SUPPLY' source, air flows through a 'REGULATOR', then potentially a 'WATER SEPARATOR' and/or 'OILER'. A 'QUICK COUPLER' connects to a 'RECOIL HOSE', which then connects via a 'NIPPLE' to a 'LEADER HOSE'. The 'LEADER HOSE' connects to the sander's 'NIPPLE'. There is a note: "DO NOT USE QUICK FIT COUPLINGS AT THIS POINT". The 'DRAIN DAILY' indicator is shown on the regulator/water separator.

Figure 2: Coupling Diagram Description: Depicts a correct and incorrect coupling setup. A green checkmark (✔️) indicates a correct connection, while a red cross (❌) indicates an incorrect connection. The diagram implies that a direct quick-fit coupling to the sander is incorrect.

5. OPERATION

5.1. BELT PREPARATION

To ensure full flexibility, and to prolong working life, the belt must be "bedded in".

• Fit new belt ensuring the direction of travel is correct, and the belt join is NOT on the nose roller. Tension belt.
• Operate the tool without a load applied at half speed for around 10 seconds, then increase to full speed for a further 10 seconds.
• Finally, at a slow operating speed, using a piece of scrap material, apply light pressure to the belt where it runs over the "shoe". Increase the operating speed steadily to maximum for a few seconds, then stop.

5.2. UNPACKING AND CHECKING

Unpack the product and check contents against the parts listed below. If there is anything damaged or missing contact your supplier immediately.

Contents:

• SA35.V2 Belt Sander.
• 3 x Sanding Belt
• 2 x Hex. Key

5.3. OPERATING PROCEDURE

• WARNING! Ensure that you have read and understood the safety instructions in Section 1.
• Loosening clamp bolt (fig.3.1. on the top of sander) allows the angle between the grip and the belt to be altered to suit the job in hand. After adjustment tighten the clamp bolt.
• Once connected to the air supply the sander is started by squeezing the trigger (2).
• To remove and replace the sanding belt push the idle pulley (3) towards the drive pulley (4) against spring pressure. The pulley bracket (5) will retract and lock allowing removal/fitting of the belt. When the new belt is in position release the pulley bracket by pushing in and holding the idle pulley, then press and hold the tension bar (6) whilst releasing the pressure on the idle pulley.
• The tracking of the belt can be altered by adjusted cross head screw (7).

Figure 3: Sander Diagram Description: This diagram shows a side view of the air belt sander with numbered parts. Key components visible include the trigger (2), idle pulley (3), drive pulley (4), pulley bracket (5), tension bar (6), and tracking adjustment screw (7). The clamp bolt (1) is indicated on the top of the sander.

6. MAINTENANCE

WARNING! Disconnect sander from air supply before changing accessories, servicing or performing maintenance. Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.

• If the air supply system does not have an oiler lubricate the sander daily with a few drops of a good grade air tool oil, such as Sealey ATO/500 or ATO/1000, dripped into the air inlet (fig.3.8) before use.
• Clean the sander after use and change belt when required.
• Loss of power or erratic action may be due to the following:
  • a) Excessive drain on the air supply. Moisture or restriction in the air line. Incorrect size or type of hose connectors. To remedy, check the air supply and follow instructions in Section 4.
  • b) Grit or gum deposits in the sander may also reduce performance. If your model has an air filter (located in the area of the air inlet), remove the filter and clean it. Flush the sander out with gum solvent oil or an equal mixture of SAE No.10 oil and kerosene. Allow to dry before use. If you continue to experience problems, contact your local Sealey service agent.
• For a full service contact your local Sealey service agent.
• When not in use, disconnect from air supply, clean and store in a safe, dry, childproof location.

ENVIRONMENT PROTECTION

Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations.

Notes and Warranty

Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Please note that other versions of this product are available. If you require documentation for alternative versions, please email or call our technical team on technical@sealey.co.uk or 01284 757505.

Important: No Liability is accepted for incorrect use of this product.

Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim.

Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR

Contact: 01284 757500 | 01284 703534 | sales@sealey.co.uk | www.sealey.co.uk