Infinix NOTE 50
Model: X6858
Exploded Diagram Specification
An exploded view diagram illustrating the internal components of the Infinix NOTE 50. The following table lists the components:
| Part Number | Description |
|---|---|
| 1 | MIDDLE COVER CNC PART |
| 2 | MAIN FPC CONDUCTIVE TAPE |
| 3 | BATTERY TAPE L |
| 4 | BATTERY TAPE R |
| 5 | FPCA SIDEKEY 2LAYER |
| 6 | SIDEKEY VOL |
| 7 | SIDEKEY FRAME |
| 8 | LENS RGB |
| 9 | UP FRAME MAIN BOARD |
| 10 | NFC FPC |
| 11 | SPEAKER BOX DOWN |
| 12 | BATTERY COVER |
| 13 | FOAM BATTERY |
| 14 | FOAM SURPPORT BATTERY |
| 15 | REAR CAM FRAME ASM |
| 16 | STEEL LENS LIGHT |
| 17 | SIM TRAY |
| 18 | RUBBER USB |
| 19 | SCREW |
| 20 | GRAPHITE LCD |
| 21 | GRAPHITE MAIN BOARD |
| 22 | CABLE |
| 23 | FPCA LIGHT 2LAY |
| 24 | FPCA FLASH LIGHT 2LAY |
| 25 | FPCA |
| 26 | WIRELESS CHARGING |
| 27 | SUB BOARD |
| 28 | MAIN BOARDS |
| 29 | FRONT CAM COB MODDLE |
| 30 | REAR CAM COB MODDLE |
| 31 | REAR CAM CSP MODDLE |
| 32 | REAR CAM LS MODDLE |
| 33 | RECEIVE MODDLE |
| 34 | ONCELL 6.78FHD |
| 35 | VIBRATOR FLAT |
| 36 | OPTICAL FINGERPRINT |
| 37 | BATTERY |
| 38 | PET FILE |
Know Your Phone
The Infinix NOTE 50 features the following components:
Front View:
- 1. Front camera
- 2. Volume + button
- 3. Volume - button
- 4. Power button
- 5. NFC (Near Field Communication)
Back View:
- 6. Wireless charging coil symbol
- NFC area
- Rear camera module
SIM Card Installation
Follow these steps for SIM card installation:
- Power off your phone.
- Refer to the following visual guide for SIM card installation.
Visual guide shows the phone with SIM card trays indicated for SIM 1 and SIM 2 insertion.
Charging the Phone
You can charge your phone using a charger or by connecting it to a computer via a USB cable (included with the phone).
Important: Use only Infinix chargers and cables. Using other chargers or cables may damage the phone and void its warranty.
Visuals show the phone being charged via a USB cable connected to its port.
FCC Caution
Labelling Requirements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- (1) This device may not cause harmful interference.
- (2) This device must accept any interference received, including interference that may cause undesired operation.
Information to User
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the device.
Information to the User
Note: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and may radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception (able to be determined by turning the device off and on), the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the device and receiver.
- Connect the device to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Specific Absorption Rate (SAR) Information
This mobile phone meets the government's requirements for exposure to radio waves. The guidelines are based on standards developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement: The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types: X6858 (FCC ID: 2AIZN-X6858) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 0.95 W/kg and when properly worn on the body is 1.14 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user's body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.
Legal and Licensing Information
For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.
Operating System: Android™
Android is a trademark of Google LLC.
