UVISION AllPlay Smart Projector

Box Contents

Please check the contents of the carton against the list below when opening the packaging. If anything is missing, please contact the seller promptly.

• Intelligent Projector
• Adapter
• Power Cable
• Remote Control
• User Manual
• Warranty Card

Note:

• The actual contents may vary depending on the country or region of sale; please refer to the actual product.
• Keep the original packaging for future storage or transport.

First Steps

Determine the distance between the projector and the wall or screen according to the desired screen size.

Projection Setup: The diagram illustrates the projector casting an image onto a screen. 'D' indicates the distance from the projector to the screen, and 'H' indicates the height from the projector's base to the bottom edge of the projected image.

Definitions:

• Screen Size (SD): The diagonal size of the projection surface (in inches).
• Relative Distance (D): The distance between the projector and the wall or screen (in cm).
• Relative Height (H): The distance between the bottom of the projector and the bottom edge of the projected image (in cm).

Note: The dimensions in the table above are for guidance only, are approximate, and may differ slightly from actual values.

Powering On

Connect the power cable to the projector and plug it into the power outlet.

Power your projector remote control by inserting the appropriate batteries (batteries not included).

Connect other devices by referring to the connection labels and descriptions on the next page.

Remote Control Battery Installation:

1. Step 1: Push the back cover in the direction of the arrow. After hearing a click, the back cover will detach from the remote.
2. Step 2: Remove the back cover and then take out the battery.
3. Step 3: Insert the battery, then place the back cover onto the remote control and push it firmly in the direction of the arrow until it clicks into place. Hearing a click indicates it has been inserted correctly.

Note:

• When inserting batteries into the remote control, pay attention to the positive (+) and negative (-) poles.
• If batteries leak, wipe the liquid immediately with a dry cloth and replace the batteries with new ones.
• Dispose of used batteries according to the local waste disposal regulations of your country or region.

Your Remote Control

The remote control provides access to various functions:

• POWER: Turns the projector on and off.
• PROFILE SELECTOR: Switch between different Google accounts.
• SETTINGS: Access the settings menu.
• GOOGLE ASSISTANT: Press the Assistant button on your remote to speak with Google Assistant.
• NAVIGATION PAD: Move up, down, left, or right, then press the center button to confirm.
• BACK: Return to the previous screen.
• HOME: Return to the home screen.
• LIVE GUIDE: Launch Play Movies & TV.
• Volume Buttons: '+' to increase volume, '-' to decrease volume.
• NETFLIX: Access the Netflix app.
• YouTube: Access the YouTube app.

Product Overview

The projector features several key components:

• Projection Lens: The primary lens for projecting images.
• Camera: Integrated camera for potential features.
• Ventilation Openings for Heat Dissipation: Allows for cooling of the projector.
• External Tripod Mount: A 1/4-inch thread (5mm depth) for mounting on a tripod.
• Speaker Sound Hole: Where sound is emitted from the speaker.
• Ventilation Openings: Additional openings for airflow.
• Port: General label for connection ports.
• Power Button and Indicator Light: For turning the device on/off and indicating status.

CAUTION! [!]

• Do not place objects within 20 cm of the heat dissipation openings.
• Do not place objects near the ventilation openings, as this can lead to heat buildup inside the projector.
• Do not look directly into the lens to avoid eye damage, as this projector emits strong light during use.

Connection Ports

The projector features the following connection ports:

1. Line-Out: Connect an analog cable to an external analog audio system.
2. HDMI: High-quality audio/video connection. Connect cable boxes, Blu-ray players, game consoles, or other devices to your projector using HDMI cables.
3. USB: Connect a USB device to access photos, music, and movies.
4. DC: Connect your projector to the power source using the included power cable.

Power Indicator

Turn the device on and off using the power button on the unit and the power button on the remote control.

The operating indicator (a soft white light) for the projector status is as follows:

• During the startup process, the indicator light is always on, then blinks breathlessly, and turns off after the system's main interface is accessed.
• After entering the system, the indicator light is always off.
• After accessing the shutdown screen, the indicator light is always on.
• When the system is in standby mode, the indicator light is off.
• The breath light is always on during the shutdown process and turns off after shutdown.

Keystones & Focus

1. Move the projector, and the screen will undergo omnidirectional automatic correction and autofocus.
2. Open the settings menu, navigate to Settings, find "Projector," and select "Keystone Correction" or "Focus" to activate the function.

Mounting Instructions

The projector features a 1/4-inch threaded mounting hole (5.5 mm depth) for attaching to mounts or tripods.

Note: For mounting, please use screws with the specified specifications and select a suitable bracket.

Specifications

Troubleshooting

Regulatory Information

The CE and UK CA marks indicate compliance with relevant standards.

UVision Innovation Co., Ltd. hereby declares that the radio equipment of type [AllPlay Smart Projector / UVAPSP-1] complies with Directive 2014/53/EU and the Radio Equipment Regulation 2017.

The full text of the declaration of conformity is available at the following internet address: http://www.uvision.com/pages/support/declaration.html

This device may only be operated indoors and in the frequency range of 5150 to 5350 MHz.

• BT maximum transmit power: 100mW at 2.4GHz - 2.4835GHz
• Wi-Fi 2.4G maximum transmit power: 100mW at 2.4GHz - 2.4835GHz
• Wi-Fi 5G maximum transmit power: 200mW at 5.15GHz - 5.25GHz, 100mW at 5.25GHz - 5.35GHz & 5.47GHz - 5.725GHz

The product complies with the standard "RG1 IEC/EN 62471-5 : 2015".

Environmental & Battery Disposal

Products bearing the WEEE symbol (crossed-out wheeled bin) are Waste Electrical and Electronic Equipment and must not be disposed of in unsorted household waste. To protect human health and the environment, please return your old equipment to a designated collection point for recycling of electrical and electronic equipment.

Proper disposal and recycling contribute to avoiding potential negative consequences for the environment and human health. Please contact your installer or local authorities for more information on the location and conditions of such collection points.

Battery Disposal: Batteries in this product must not be disposed of in household waste at the end of their life. Chemical symbols Hg, Cd, or Pb indicate the presence of mercury, cadmium, or lead, which may exceed EC Directive 2006/66 limits. Improper battery disposal can harm human health or the environment. To protect natural resources and promote material reuse, please separate batteries from other waste and recycle them through your local, free battery return system.

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This device has been tested and complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in residential installations.

This device generates and uses radio frequency energy and may radiate it. If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If interference occurs, try one or more of the following:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and the receiver.
• Connect the device to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Important: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

RF Exposure & Canadian Compliance

RF Exposure Information: The radiated output power of this device meets the FCC/IC limits for radio frequency exposure. This device should be operated with a minimum separation distance of 20 cm (8 inches) between the device and a person's body.

Canadian Compliance: This device complies with Innovation, Science and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

The 5150-5250 MHz frequency band is reserved for indoor use only to reduce the potential for interference with mobile satellite systems that use the same channels.

RF Exposure: The radiated output power of this device complies with FCC/IC limits for radio frequency exposure. This device should be used with a minimum separation distance of 20 cm (8 inches) between the device and a person's body.

CAN ICES-003 (B)/NMB-003(B)

This device complies with Canadian regulatory requirements for innovation, science, and economic development applicable to license-exempt radio equipment. Use is permitted under the following conditions: (1) the device must not generate radiation, and (2) the user of the device must accept any radiation, even if it could affect the device's function.

Safety Precautions

CAUTION! [!]

• There is a risk of explosion if the battery is replaced with an incorrect type.
• Disposing of a battery in fire or a hot oven, or mechanically crushing or cutting a battery, can lead to an explosion.
• Leaving a battery in an environment with extremely high temperatures may lead to an explosion or leakage of flammable liquids or gases.
• A battery exposed to extremely low air pressure may lead to an explosion or leakage of flammable liquids or gases.

Product Certifications

Dolby Audio: Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

HDMI: The terms HDMI, HDMI High-Definition Multimedia Interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

Bluetooth: Indicates Bluetooth connectivity.

Google TV: Google TV is the software name for this device and a trademark of Google LLC. Google and YouTube are trademarks of Google LLC.

Google Assistant is not available in all languages and countries. Service availability varies by country and language.

Product labeling and safety information are located on the bottom of the product.

Support

For support, please visit: www.uvision.com

Contact: support@uvision.com.tw