Industrial Monitors & Touch Screens - Hope Industrial Systems
Instruction Manual for HIS models including: KB-M2-WMT, KB-R2-WMT, KB-R3-WMT, KB-M2-WMT Wall Mount Folding Keyboard, KB-M2-WMT, Wall Mount Folding Keyboard, Mount Folding Keyboard, Folding Keyboard, Keyboard
File Info : application/pdf, 4 Pages, 1.33MB
DocumentDocumentInstallation Instructions KB-M2-WMT- _ _ , KB-R2-WMT- _ _ , and KB-R3-WMT- _ _ Series Wall Mount Folding Keyboard 1. Cut or drill mounting pattern in panel using the provided cutout template. Refer to Figure 1 for the panel mounting pattern. NOTE: +/- 0.8 mm (0.03") tolerance on all dimensions unless otherwise noted. The provided hardware is for use with panels that have a maximum thickness of 6.4 mm (1/4") if using clearance holes. Thicker panels can be used but require 1/4-20 tapped holes or longer screws than those provided. For thicker panels or panels where rear access requires a second person, you must install the plastic bulkhead fitting onto the left hand wall bracket first (as shown in steps 7 and 8), and then proceed from step 1. 38.1 mm (1.50") 76.2 mm (3.00") 31.8 mm (1.25") 11.1 mm (0.438") Ø 31.8 mm (1.25") 450.85 mm (17.75") + 2.3 mm (0.09") - 0.8 mm (0.03") Ø 8 mm (5/16") DIAMETER OR 1/4-20 TAPPED HOLES (PREFERRED FOR EASIER INSTALLATION) (8 PLACES) 25.4 mm (1.00") PLACE 44" OFF FLOOR FOR MOST UNIVERSAL ERGONOMIC HEIGHT FIGURE 1 PANEL MOUNTING PATTERN 2. Install the left hand wall bracket first using four of the provided 1/4-20 screws, washers, and nuts as shown. Tighten all screws until the gasket is compressed to 1/16" to 3/32" thick. RUBBER WASHER NYLON WASHER NUT 1/4-20 SCREWS 1/4-20 SCREWS GASKET LEFT HAND WALL BRACKET FIGURE 2 SIDE VIEW AND FRONT VIEW OF LEFT HAND WALL BRACKET 99109A · December 20, 2022 · www.HopeIndustrial.com · International: +1 (678) 762-9790 · UK: +44 (0) 20 7193 2618 · © 2023 Hope Industrial Systems, Inc. · Page 1 of 4 Wall Mount Folding Keyboard Installation Instructions (continued) 3. Loosely install the right hand wall bracket using only 1 of the provided 1/4-20 screws, washers, and nuts in the location shown. The remaining three screws will be installed after fitting the keyboard in place. 1/4-20 SCREW RUBBER WASHER NYLON WASHER NUT 1/4-20 SCREW RIGHT HAND WALL BRACKET FIGURE 3 FRONT VIEW AND SIDE VIEW OF RIGHT HAND WALL BRACKET 4. Slide the keyboard cable through the slot on the left hand wall bracket as shown. IMPORTANT! THE KEYBOARD MUST BE SUPPORTED SO THAT NO PRESSURE OR WEIGHT IS APPLIED TO THE CABLE ITSELF DURING THE INSTALLATION PROCESS. CABLE FIGURE 4 FRONT VIEW SHOWING KEYBOARD 99109A · December 20, 2022 · www.HopeIndustrial.com · International: +1 (678) 762-9790 · UK: +44 (0) 20 7193 2618 · © 2023 Hope Industrial Systems, Inc. · Page 2 of 4 Wall Mount Folding Keyboard Installation Instructions (continued) 5. Swing the right hand wall bracket into place, trapping the keyboard as shown. RIGHT HAND WALL BRACKET FIGURE 5 FRONT AND SIDE VIEWS 6. Finish installing the right hand wall bracket using the remaining three 1/4-20 screws, washers, and nuts. Tighten all screws until the gasket is compressed to 1/16" to 3/32" thick. GASKET 1/4-20 SCREWS FIGURE 6 FRONT VIEW 7. Unscrew the first nut from the plastic bulkhead fitting on the keyboard cable and remove from the end of the cable. PLASTIC BULKHEAD FITTING NUT FIGURE 7 FRONT VIEW 99109A · December 20, 2022 · www.HopeIndustrial.com · International: +1 (678) 762-9790 · UK: +44 (0) 20 7193 2618 · © 2023 Hope Industrial Systems, Inc. · Page 3 of 4 Wall Mount Folding Keyboard Installation Instructions (continued) 8. Insert the cable and fitting through the hole in the left hand wall bracket. Tightly reinstall the nut from the rear. Push the cable through as far as it will go, then tighten the cable gland nut from the front. IMPORTANT! FAILURE TO FULLY TIGHTEN EITHER NUT WILL COMPROMISE THE WATERTIGHT SEAL ON THE PANEL. NUT PANEL CABLE FIGURE 8 TOP AND FRONT VIEWS CABLE GLAND NUT CABLE FIGURE 9 TOP AND FRONT VIEWS LIFT TO DISENGAGE FROM LOCK UP POSITION KEYBOARD HAS 4 POSITIONS: LOCK UP TYPE UP/FLAT TYPE DOWN LOCK DOWN PULL TO DISENGAGE FROM LOCK DOWN POSITION FIGURE 10 SIDE VIEW SHOWING 4 POSITIONS 99109A · December 20, 2022 · www.HopeIndustrial.com · International: +1 (678) 762-9790 · UK: +44 (0) 20 7193 2618 · © 2023 Hope Industrial Systems, Inc. · Page 4 of 4