LECTRIC XP PROGRAMMING AND FUNCTIONS CHART
Options that are in bold are the ones you are most likely to change.
Options in red should not be changed unless advised by authorized rep
Example of Programming Steps
Change top speed
- Access the settings menu by pressing and holding up and down together until the screen says P1
- Cycle through the programs by pressing the M (mode) button and use up/down to modify the values
- In this case go to P08 and change the setting from 32 to 45 (km/h)
- Press and hold up/down together until the main screen is shown
- Press and hold the M (mode) button to save the new value and exit program mode
Programming Functions
| Program number / Function | Defaults | My Settings | Extended description |
|---|---|---|---|
| P01: 1-3 Screen brightness | 1-3 | 3 | Backlight Brightness Adjustment, 1 Lowest, 3 Brightest. |
| P02: mph or kph | 1 | 1 | Mileage Unit Setting. 0: km, 1:mile |
| P03: 48V Voltage | 48 | 48 | 48V Voltage Selection Setting. 24V 36V 48V |
| P04: Sleep Timer | 10 | 10 | Sleep Time. 0: No Sleep, Other Numbers Are Sleep Time, 1-60 Minutes |
| P05: PAS levels available | 1 | 1 | Power Assist Levels available. 0=0-3, 1=0-5, 2=0-9, 3=0-4, 4=0-6 |
| P06: Tire diameter | 20 | 22.0 | Rim Diameter. Mine needed to be set to 25.5 to correct my odometer |
| P07: Number of speed magnets | 1 | 1 | Number of Speed Magnets. Range: 1-100 |
| P08: Max speed | 32 (km/h) | 45 | 32 or 45 Speed Limit: 0-100km/h. MAX is 45km/h |
| P09: Throttle Zero Start | 0 | 0 | 0: throttle active from standstill 1: throttle active only when already moving |
| P10: Drive Mode | 2 | 2 | 0=Pedal Assist only, 1=Throttle only, 2=Both pedal assist and throttle. |
| P11: 3 Pedal assist sensitivity | 3 | 2 | 1-24 PAS sensitivity. Higher numbers take more rotation to turn on |
| P12: 3 | 3 | 5 | PAS strength 1-5. Higher numbers cause motor to come on stronger |
| P13: 12 do not change | 12 | 12 | Magnet type 5, 8, 12 |
| P14: 18 do not change | 18 | 18 | Current limiting. 1-20 amps |
| P15: 41.5V low volt protection | 41.5 | 40 | The lower limit voltage (where the motor cuts off) |
| P16: Zero odometer | 6 seconds | Odometer zero. Long press the upper key for 5-6 seconds | |
| P17: Auto cruise | 0 | 0 | Maintain steady speed for 6 seconds to activate |
| P18: calibrate speedo | 100 | 100 | Adjust for rim and tire size |
| P19: PAS Zero Gear yes/no | 0 | 0 | 0=no zero gear, 1=has zero gear |
| P20: comm protocol | 0 | 0 | Do not change |
| P21 Walk Mode Toggle | 1 | 1 | 0: Walk mode disabled 1: Walk mode enabled |
Options while riding
- Walk Mode 3mph: Hold down button for 2-3 seconds
- Cruise Control: Hold down button for 2-3 second while throttle is in use
- Lights on / off: Hold up button for 2-3 seconds to toggle on / off
- Change PAS level: Use Up and Down buttons (short press, one press per level)
- Max Speed and Average Speed: Press and hold the up arrow and mode button simultaneously to toggle between the speedometer, max speed, and average speed
