PROFLO Single Handle Pre-Rinse Kitchen Faucet

Installation Instructions

Important Safety Information

Tips for Removal of Old Faucet:

Always turn off the water supply before removing the existing faucet or replacing any part of the faucet. Open the faucet handle to relieve water pressure and ensure that water is completely shut off.

Care Instructions:

To preserve the finish of your faucet, apply non-abrasive wax. Any cleaners should be rinsed off immediately. Do not use abrasive cleaners on the faucet.

Tools and Parts You May Need

Safety Goggles ?
Adjustable Wrench ?
Two Supply Lines
Basin Wrench
Sealant Tape
Silicone Sealant
Phillips Head Screwdriver

Installation Steps

Step 1: Optional Flange Installation

Shut off water supplies. Before installation, ensure that the flange (1) is placed on the bottom of the new faucet assembly. Insert faucet body through the sink hole. Install plastic washer (2) and metal washer (3) onto the threaded mounting shank. Thread nut (4) onto the mounting shank. Lock nut into position by tightening screws (5). Do not overtighten. Please continue to Step 4. If installing the faucet with the escutcheon, begin with Step 2.

Diagram shows faucet body, flange (1), plastic washer (2), metal washer (3), threaded shank, nut (4), and screws (5). Maximum torque for screws is 2 N.m.

Step 2: Optional Escutcheon Installation

Shut off water supplies. Before installation, remove the flange (1). Screw the bolts (2) into the escutcheon (3) and ensure that the base plate (4) is pressed onto the escutcheon (3) before the escutcheon (3) is installed over the three holes in the sink. From underneath the sink, hand tighten the mounting nuts (5). Do not overtighten. If installing the faucet without the escutcheon, begin with Step 1.

Note: If the sink surface is uneven or irregular, plumber's putty or a silicone sealant may be used to create a watertight seal. Plumber's putty may have an adverse reaction with plastic gaskets under the spout base, so if your faucet has a plastic gasket, use a high-quality silicone sealant. Plumber's putty may also have an adverse reaction with some cultured marble or natural stone. In these cases, a high-quality silicone sealant is recommended.

Diagram shows escutcheon (3) with bolts (2), base plate (4), and mounting nuts (5) being tightened from below.

Step 3: Optional Escutcheon Installation (Alternative View)

Insert faucet body through the hole in the escutcheon. Install plastic washer (1) and metal washer (2) onto the threaded mounting shank. Thread nut (3) onto the mounting shank. Lock nut into position by tightening screws (4). Do not overtighten.

Diagram shows faucet body inserted into escutcheon, with plastic washer (1), metal washer (2), mounting nut (3), and screws (4).

Step 4: Making the Waterline Connections

Thread the nut (1) on the supply line onto the outlet of the water supply valve (2) and tighten with a wrench. Do not overtighten.

Diagram shows supply line nut (1) connecting to water supply valve outlet (2), with a wrench used for tightening.

Step 5: Final Flushing and Operation Check

After installation is complete, remove the sprayer by unscrewing it in a counter-clockwise direction. Turn on the water supply to flush debris from the faucet. Run the hot and cold water for at least one minute each. Important: This flushes away any debris that could cause damage to internal parts.

Diagram shows the faucet with the sprayer detached and water running through it.

Maintenance

If the faucet leaks underneath the handle or the water does not completely shut off: Replace the cartridge.

Parts List

The following parts are included or referenced in the installation:

Sprayhead: OBPF638340* (Cabezal de rociado / Tête de vaporisation)
Cartridge: OBPF220120 (Cartucho / Cartouche)
Handle: OBPF717126* (Llave / Poignée)
Flange (1)
Plastic Washer (2)
Metal Washer (3)
Mounting Nut (4)
Mounting Screws (5)
Escutcheon (3)
Base Plate (4)
Bolts (2) for Escutcheon
Mounting Nuts (5) for Escutcheon
Supply Line Nut (1)
Water Supply Valve Outlet (2)
Plastic Washer (1) for Escutcheon
Metal Washer (2) for Escutcheon
Mounting Nut (3) for Escutcheon
Mounting Screws (4) for Escutcheon
Sprayer Hose
Various seals and O-rings

For more information, visit www.PROFLO.com.

Distributed Exclusively by Ferguson and Wolseley Canada.

	PROFLO PFXC1701 Kiger Series Single Handle Kitchen Faucet - Features, Specifications, and Warranty Detailed information on the PROFLO PFXC1701 Kiger series single handle kitchen faucet, including product features, model numbers, specifications, optional parts, and warranty information. Compliant with ASME A112.18.1, NSF 61, CUPC/IAPMO, and ADA standards.
	PROFLO PFXC9512 Roystone Series Single Handle Kitchen Faucet - Specifications Detailed specifications for the PROFLO PFXC9512 Roystone Series single handle kitchen faucet, featuring a pull-down sprayer, ceramic disc cartridge, and compliance with ASME, CSA, cUPC, IAPMO, ADA, and NSF standards. Available in Chrome (PFXC9512CP) and Brushed Nickel (PFXC9512BN). Includes dimensions and warranty information.
	PROFLO PFXM334 Two Handle Metering Faucet Installation Guide Comprehensive installation, care, and troubleshooting guide for the PROFLO PFXM334 two-handle metering faucet, including a detailed parts list and required tools. Learn how to install and maintain your faucet.
	PROFLO Two Handle Kitchen Faucet PFXCM2M209 Parts Breakdown and Warranty Comprehensive parts breakdown, model specifications, and warranty information for the PROFLO Two Handle Kitchen Faucet (Model PFXCM2M209). Includes part numbers, compliance details (ANSI, NSF, UPC, Low Lead), and manufacturer information.
	PROFLO KIGER Single Handle Kitchen Faucet Installation Instructions Detailed installation and care instructions for the PROFLO KIGER Single Handle Kitchen Faucet (Model PFXC1701CP/ZBN/MB). Includes warnings, required tools, step-by-step installation guidance, and a parts list. Installation by a licensed plumber is recommended.
	PROFLO PF1119 Two-Handle Wall Mount Service Sink Faucet Specifications and Features Detailed specifications, features, available parts, and flow rate information for the PROFLO PF1119 two-handle wall mount service sink faucet. Includes warranty details and compliance standards.
	PROFLO Laundry Tray Faucet PF760 Parts Breakdown and Warranty Detailed parts breakdown, identification, and warranty information for the PROFLO Laundry Tray Faucet, model PF760. Includes materials and compliance standards.
	PROFLO PFXC5512 Single Handle Pre-Rinse Kitchen Faucet - Scovin Series Detailed overview of the PROFLO PFXC5512 Single Handle Pre-Rinse Kitchen Faucet from the Scovin series, including model numbers, parts list, and warranty information.