BUTURE JR700 Stick Vacuum Cleaner User Manual
1. Introduction
Thank you for purchasing the BUTURE JR700 stick vacuum cleaner. Please read this user manual carefully before use to prevent malfunctions caused by accidental operation. If the product is transferred to another person, ensure the manual is included. The product comes with a free 2-year warranty; please activate the warranty card promptly. For any questions, contact sales@ibuture.com.
2. Warning
2.1 Personal Safety
- Store the appliance indoors in a dry place, out of the reach of children.
- This product is suitable for children aged 10 years and above. Users with reduced physical functions, sensory or intellectual abilities, or lack of experience and knowledge should use the product under supervision or guidance and be aware of potential hazards.
- Exercise caution when children or pets are near the vacuum cleaner.
- Children should not clean or use the product without supervision.
- Use only manufacturer-recommended attachments as described in this manual. Misuse or use of unauthorized accessories may pose a risk of personal injury.
- Take extra care when cleaning stairs.
- Keep the appliance and accessories away from hot surfaces.
- Do not block the appliance's openings or hinder airflow. Keep openings free of objects such as dust, lint, clothing, fingers, or any other body parts.
2.2 Electrical Safety
- Only use batteries and chargers supplied by the manufacturer.
- Never modify the charger in any way.
- To disconnect from a socket, grasp the plug and pull; do not pull the cord.
- Keep the charger cord away from hot surfaces and sharp edges.
- The supply cord cannot be replaced. If the cord is damaged, the charger must be discarded and replaced.
- Do not handle the charger or the appliance with wet hands.
- Do not store or charge the appliance outdoors.
- The charger must be removed from the socket before removing the battery, cleaning, or maintaining the appliance.
2.3 Battery Safety
- This appliance includes Li-ion batteries. Do not incinerate batteries or expose them to high temperatures, as they may explode.
- Liquid ejected from the battery may cause irritation or burns.
- In an emergency, seek professional help immediately.
- Battery cell leaks can occur under extreme conditions. Do not touch any leaked liquid. If liquid contacts the skin, wash immediately with soap and water. If liquid gets into the eyes, flush them immediately with clean water for at least 10 minutes and seek medical attention. Wear gloves when handling the battery and dispose of it according to local regulations.
- When the battery pack is not in use, keep it away from small metal objects like paper clips, coins, keys, nails, or screws that could create a connection between terminals.
- When disposing of the appliance, remove the battery and dispose of it safely in accordance with local regulations.
3. Content of Package
| Part Name | Quantity | Part Name | Quantity |
|---|---|---|---|
| Main Body | 1 | Charging Stand | 1 |
| Battery Pack | 1 | Charger | 1 |
| Telescopic Tube | 1 | Small Cleaning Brush | 1 |
| Floor Brush | 1 | Air Filter (Installed) | 1 |
| Hard And Soft Bristle Integrated Brush (Installed) | 1 | Hepa Dust Filter (one is installed in the main body) | 3 |
| Crevice Nozzle | 1 | Screws set (Used to install wall mount stand) | 1 |
| Round Brush | 1 | Quick User Guide | 1 |
4. Know Your Product
The BUTURE JR700 features an LED Touch Screen, ON/OFF button, suction adjustment, and various accessories. Key components include the main body, battery pack, telescopic tube, dust cup, and floor brush. Indicators on the device show battery status, suction levels, and potential blockages.
Main Unit Components:
- LED Touch Screen
- Tube Release Button
- Telescopic Tube
- Length Adjustment Button
- Floor Brush Release Button
- Floor Brush
- Battery Release Button
- Battery
- ON/OFF Button
- Battery Indicator
- Dust Cup Release Button
- Dust Cup
Indicators:
- Battery Indicator
- Brush Roller Tangled (Indicator flashes)
- Suction Indicator
- Air Passage/Dust Cup Blocked (Indicator flashes)
- Suction Adjustment Button
Included Accessories:
- Round Brush
- Charging Stand
- Charger
- Crevice Nozzle
- Hard And Soft Bristle Integrated Brush (Installed)
- Small Cleaning Brush
5. Charging
Ensure the power is turned off before charging.
- Only use the original charger to prevent damage to the vacuum cleaner.
- During overcurrent and overvoltage protection, the battery indicators will flash simultaneously, and the screen will turn off.
Two Charging Ways:
- Charge the battery directly: Connect the battery to the charger.
- Charging on the stand: Place the vacuum cleaner on the charging stand.
When the battery indicator shows 100%, the battery is fully charged and ready for use.
6. Assembling
Connect the telescopic tube: Insert the telescopic tube into the main body and ensure it is securely attached. Press the release button to detach the telescopic tube.
Connect brush heads: Attach the desired brush head to the end of the telescopic tube or main unit.
7. Using
Important: Do not exceed the "MAX" dust collection capacity of the dust cup. Keep the suction nozzle unobstructed to prevent blockage, which could cause the motor to overheat and lead to danger.
- Start Work: Press the ON/OFF button.
- Adjust Suction Power: Touch the suction adjustment button to cycle through power modes:
- Green light: ECO mode.
- Blue light: Standard mode.
- Red light: Max suction mode.
The length of the telescopic tube can be adjusted according to different needs.
8. Cleaning
8.1 Clean the Dust Cup
To maintain optimal suction power, empty the dust cup and clean the filter after each use.
- Press the release button on the dust cup to open its lid and empty the contents into the trash.
- Press the dust cup release button on the main body, grasp the bottom of the dust cup, and remove it.
- Pull out the HEPA filter. Open the bottom cover of the dust cup, rotate the stainless steel filter, and remove it.
- Sweep dust off the HEPA filter using the cleaning brush. The stainless steel filter and dust cup can be washed with water and must be dried for 24 hours before reinstallation.
Note: Do not use washing machines, dryers, or irons to clean the filter. Allow natural drying only.
8.2 Reinstallation
- Insert the stainless steel filter from the bottom of the dust cup and rotate it tightly. Ensure the three small protrusions on the filter's edge align with the three small grooves on the dust cup.
- Place the HEPA filter from above and secure the bottom cover.
- Align the convex part of the handle with the concave part of the dust cup, insert it, and press the dust cup release button to fully close the dust cup and handle.
8.3 Clean the Brush
Ensure the appliance is disconnected from the charger before removing the roller brush. Avoid pulling the ON button.
- Push the switch to the "unlock" side, remove the plug, and then take out the roller brush.
- Use the small cleaning brush to sweep away debris from the roller. The knife edge on the brush is designed to remove tangled hairs.
- Clean the roller brush with or without water.
- Gently push the roller brush back into place. Ensure the brush is completely dry before reinstallation.
9. Troubleshooting
If you encounter any problems during use, consult the troubleshooting table below. If the issue cannot be resolved, please contact the after-sales service at sales@ibuture.com.
Warning: Always turn off the vacuum cleaner before performing maintenance to avoid electric shock or personal injury.
9.1 Blockage Protection
- Brush Roller Tangled: If the floor brush picks up large objects or becomes entangled with excessive hair, the indicator on the left will flash.
- Solution: Remove the floor brush and clean any foreign matter wrapped around the roller. Ensure the brush head is detached from the main unit to prevent accidental starting and potential injury.
- Air Passage or Dust Cup Blocked: The indicator on the right will flash if the air passage or dust cup is blocked.
- Solution: Thoroughly clean the aluminum tube and the filters in the dust cup.
10. Common Trouble
| Problems | Possible Causes | Solutions |
|---|---|---|
| Vacuum can not work | 1. Low battery power. 2. Blockage in floor brush, telescopic tube, dust cup, or filter. 3. Not charging with the original charger. 4. Battery not installed properly. 5. Battery damaged. | 1. Charge before use. 2. Clean blockages in brush suction inlet, extension tube, dust cup, HEPA filter, and metal filter. 3. Ensure charging with the original charger. 4. Verify battery installation. 5. Contact sales@ibuture.com. |
| Suction power becomes weak | 1. Dust cup is full. 2. Metal filter blocked by dust. 3. HEPA filter blocked by dust. 4. Low battery power. 5. Attachments (extension tube, clean head) not installed correctly. 6. Air outlets or inlets blocked by debris. | 1. Clean the dust cup. 2. Clean the metal filter. 3. Clean or replace the HEPA filter (replacement filters available via sales@ibuture.com). 4. Charge the battery. 5. Reinstall attachments as per instructions. 6. Clean the floor brush and extension tube. |
| Insufficient running time after charging | 1. Insufficient charging time. 2. Battery aging. 3. Dust cup is full. 4. Filters are full of dust. 5. Telescopic tube or brush inlet blocked. 6. Consistently using the highest speed for cleaning. | 1. Recharge the battery. 2. Replace the battery. 3. Empty the dust cup. 4. Clean or replace the HEPA filter. 5. Remove blockages in the tube and brush inlet. 6. For general cleaning, use low or medium speed. High speed is for heavy debris and prolongs battery life. For larger homes, consider purchasing additional spare batteries from sales@ibuture.com. |
| LED indicator is not light | 1. Charging cable not fully inserted. 2. Foreign matter on charger contacts or battery port. 3. Charging socket damaged. 4. Vacuum cleaner motor damaged. 5. Battery damaged. 6. Charger damaged. | 1. Ensure charger, battery, and power socket are in good contact. 2. Verify charging contacts are clean. 3. Try a different charging socket. 4. Contact sales@ibuture.com for motor replacement. 5. Contact sales@ibuture.com for battery replacement. 6. Contact sales@ibuture.com for charger replacement. |
| Electric floor brush roller does not rotate | 1. Roller brush wrapped or entangled by hair. 2. Roller brush not installed properly. 3. Extension tube or electric floor brush not installed properly. 4. Extension tube damaged. 5. Floor brush damaged. | 1. Follow instructions to clean the floor brush and restart. 2. Follow instructions to reinstall the roller brush. 3. Follow instructions to reinstall the extension tube and floor brush. 4. Contact after-sales for extension tube damage. 5. Contact after-sales for floor brush damage. |
| Vacuum cleaner leaks dust | 1. HEPA filter not installed or not in place. 2. HEPA filter full of dust. 3. Metal filter full of dust. 4. HEPA filter damaged and needs replacement. 5. Ensure dust is contained in the dust cup before turning off. | 1. Check HEPA filter installation. 2. Clean the HEPA filter. 3. Clean the metal filter. 4. Contact customer service for a replacement HEPA filter. 5. Ensure all debris is in the dust cup before powering off. |
| The vacuum cleaner stops automatically | 1. Out of battery. 2. Clogged suction ports causing overheating. 3. Clogged HEPA filter causing overheating. 4. HEPA filter needs replacement. | 1. Charge the battery. 2. Clean all air inlets and allow the vacuum to cool to room temperature before restarting. 3. Clean the HEPA filter, dust cup, floor brush, and metal filter. 4. Replace the HEPA filter. |
10. Common Trouble (Error Codes)
| Problems | Possible Causes | Solutions |
|---|---|---|
| Display turns black and shows E1 in the middle | Over temperature protection | The current battery temperature is high. Stop using or charge the vacuum cleaner until the battery temperature returns to normal (approximately 45 minutes). |
| Display turns black and shows E2 in the middle | Abnormal charger voltage | When the adapter voltage is too high or too low, the display will flash "E2" quickly, and a red light will flash on the battery. The machine will automatically shut down after 10 seconds. Contact sales@ibuture.com. |
| Display turns black and shows E3 in the middle | Battery failure | When the battery fails, the display will flash "E3" quickly, and a red light will flash on the battery. The machine will automatically shut down after 10 seconds. Contact sales@ibuture.com. |
| Display turns black and shows E4 in the middle | Negative Temperature Coefficient connection abnormal | When the Negative Temperature Coefficient is abnormal, the display will flash "E4" quickly, and a red light will flash on the battery. The machine will automatically shut down after 10 seconds. Contact sales@ibuture.com. |
| Display turns black and shows E5 in the middle | Host overcurrent protection | To protect the host, over-current protection is activated. When the host experiences over-current, the display will flash "E5" quickly, and a red light will flash on the battery. Temporarily stop using the vacuum cleaner and wait a while before using it again. |
11. Maintenance
- The stainless steel filter and dust cup can be washed by water. Ensure they are thoroughly dried before reinstallation. Do not immerse the HEPA filter or main unit in water or any liquid.
- Clean the vacuum cleaner casing with a soft, slightly damp cloth. Prevent any liquid from entering the hoover.
- Do not use corrosive chemicals or abrasives.
- It is recommended to change the HEPA filter every 2 months (depending on usage) for optimal performance. Do not use the filter if it is damaged or worn out.
12. Warranty
If you experience any problems or malfunctions during use, please send your query and order number to sales@ibuture.com. You will receive a response within 24 hours. For longer battery life, contact sales@ibuture.com for additional batteries.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception (which can be determined by turning the equipment off and on), the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Correct Disposal of this Product
This marking indicates that the product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the designated return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
Declaration of Conformity
Manufacturer: Ekoo Electronic Co.,Ltd.
Company Address: B09, block B, f2, bldg. b, runfeng Pioneer Park, no.973, minzhi Avenue, Minzhi St., Longhua, Shenzhen, CN.
Declare under their sole responsibility that the product:
- Trade name: BUTURE
- Equipment: Vacuum Cleaner
- Model No.: JR700
To which this declaration relates is in conformity with the essential requirements set out in the Council Directive on the Approximation of the laws of the Member States relating to LVD Directive (2014/35/EU) & EMC Directive (2014/30/EU) & RoHS (2011/65/EU). The product is responsible for affixing the CE marking. The following standards were applied:
- EN 60335-2-2:2010+A11:2012+A1:2013
- EN 60335-1:2012+A11:2014+A13:2017+A1:2019+A14:2019+A2:2019
- EN 62233:2008
- EN 55014-1:2021
- EN 55014-2:2021
- EN IEC 61000-3-2:2019+A1:2021
- IEC62321-3-1:2013
- IEC62321-4:2013
- IEC62321-5:2013
- IEC62321-6:2015
- IEC62321-7-1:2015
- IEC62321-7-2:2017
- IEC62321-8:2017
Full Name: George.wang
Signature: George.wang
Position: Approbation Manager
Place/Date: Shenzhen, China/Jun.27-2022
