Kraus Bolden Single Handle Pull Down Kitchen Faucet

Model: KPF-1610

INSTALLATION MANUAL

Congratulations on the purchase of your new Kraus plumbing fixture!

Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance or have any problems with your product:

Prior to Installation:

• Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement.
• Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber's putty, or silicone.
• Flush angle stops to release any debris prior to installation.
• Pre-drilled hole size requirement: 1 3/8" (min)
• Max countertop thickness: 1 3/4"

For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help:

Toll-Free: 800-775-0703 or Customerservice@kraususa.com

Tools Required

Diagram describing tools: ? Adjustable Wrench, ? Phillips Screwdriver, ? Silicone Sealant, ? Safety Goggles, ? Pipe Tape.

Diagram and Parts List

Diagram illustrating the Kraus Bolden kitchen faucet components. Labeled parts include: A. Spray Head, B. Faucet Body, C. Mounting Hardware (C1. Rubber & Metal Washer, C2. Mounting Nut, C3. Mounting Screws), D. Quick Connector, E. Weight (E1. Weight Clip, E2. Weight), F. 2.5mm Hex Wrench.

Faucet Dimension

Diagram showing faucet dimensions in inches and millimeters. Key dimensions include: Overall Height (18"), Spout Height (4 1/2"), Spout Reach (3 1/2"), approximate extended hose height (10 3/4"), deck to aerator height (6 3/8"), base diameter (Ø1 7/8"), hose length (17"), water connection thread (9/16" - 24UNF), base diameter at deck (Ø2 1/8"). Includes a 25° angle for the spout and a 90° angle for the handle.

Installation Steps:

Step 1. Remove mounting hardware

Shut off the water supply. Remove the old faucet. Clean the mounting surface. Remove mounting hardware (C) from faucet body (B).

Diagram showing the faucet body (B) with mounting hardware (C) being detached. An arrow indicates removal.

Step 2. Installing the faucet assembly

Optional No Escutcheon Installation. Insert faucet body through the hole in the sink.

Diagram showing the faucet body being inserted through a countertop hole. An arrow indicates downward insertion. An optional escutcheon plate is shown.

Step 3. Securing the faucet assembly

Install the rubber washer and metal washer (C1) onto the threaded mounting shank. Thread the nut (C2) onto the mounting shank. Lock the nut (C2) into position by tightening the screws (C3). Do not overtighten.

Diagram showing the installation of washers (C1), mounting nut (C2), and screws (C3) onto the faucet's threaded shank. Arrows indicate assembly.

Step 4. Securing the faucet assembly

Push the quick connector (D) firmly upward and attach it to the receiving block (1). Pull down moderately to ensure the connection has been made.

Diagram showing the quick connector (D) being attached to a receiving block (labeled '1'). An arrow indicates upward insertion, followed by a moderate pull-down motion.

Step 5. Securing the faucet assembly

Install the weight clip (E1) at the point of the hose marking "weight here". Insert the weight (E2) onto the clip (E1) by sliding it down onto the clip (E1).

Diagram illustrating the attachment of the weight clip (E1) to the hose, marked 'Weight here'. The weight (E2) is then shown being slid onto the clip (E1). Arrows indicate the sliding motion.

Step 6. Making the waterline connections

Thread the nut (1) on the supply line onto the outlet of the water supply valve and tighten with a wrench. Do not overtighten.

NOTE: Please make sure filter washers are installed before connecting to the main valve.

Diagram showing water supply lines being connected to angle stops (labeled '1'). Nuts on the supply lines are tightened with a wrench.

Step 7. Flushing and checking for leaks

Pull the hose assembly out of the spout and remove the spray head by unscrewing it from the hose in a counterclockwise direction. Hold the end of the hose down into the sink and turn the faucet on to the warm position. Flush the water lines for one minute. Check for leaks. Re-tighten any connections if necessary. Reinstall the spray head by hand tightening it back onto the spray hose. Turn on the hot and cold water supplies. Check for leaks.

Diagram showing the spray head being unscrewed from the hose. The hose end is directed into the sink. Arrows indicate counterclockwise unscrewing and flushing.

Replacement Parts

Diagram illustrating various replacement parts for the faucet, numbered 1 through 25.

*Denotes spray hose assembly color options: Spray hose assembly color options: Black hose w/ Brushed Gold connector (BLBG), Black hose with Spot-Free Stainless connector (BLSFS), Gray hose with Chrome connector (GRCH), Gray hose with Spot-Free Stainless connector (GRSFS), Gray hose with Stainless Steel connector (GRSS), Black hose with Matte Black connector (BLMB), Black hose with Stainless Steel connector (BLSS), Black hose with Spot-Free Antique Champagne Bronze (BLSFACB)

**Denotes faucet component color options: CH - Chrome, SFS - Spot Free Stainless Steel, SS - Stainless Steel, MB - Matte Black, BG - Brushed Gold, SB - Black Stainless, MBSFSB - Matte Black/Spot Free Stainless Steel, SFACB - Spot Free Antique Champagne Bronze, SFACBMB - Spot Free Antique Champagne Bronze/Matte Black, MBSB - Matte Black/Black Stainless, SFSCH - Spot Free Stainless Steel/Chrome, BGMB - Brushed Gold/Matte Black, SFSB - Spot Free Black Stainless, SFSMB - Spot Free Stainless Steel/Matte Black, SSMB - Stainless Steel/Matte Black, SSCH - Stainless Steel/Chrome, BL - Black, WH - White, GR - Grey

Trouble-Shooting

If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps:

Care & Maintenance

To keep the product clean & shining, follow the steps below:

1. Rinse with clean water & dry with a soft cloth ?
2. Do not clean with soaps, acid, polish, abrasives or harsh cleaners ?
3. Do not use cloth with a coarse surface ?
4. Unscrew the aerator and clean when necessary ?

This installation manual is subject to change without further notice.

Codes/Standards Applicable:

• NSF/ANSI 61-9
• NSF/ANSI 372
• UPC C Ⓡ
• UPC C Ⓡ
• ASME A112.18.1 1.8GPM 6.8L/min maximum

FAUCET WARRANTY

Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus").

Kraus extends this warranty to the original purchaser for personal household use of the "Faucet" in its original location. The warranty is non-transferable.

Kraus warrants the structure and finish of the product to be free from defects in material and workmanship under normal usage for the lifetime of the product. The warranty commences from the initial date of purchase by the owner or trade professional, from an authorized Kraus dealer, through the lifetime of the original owner or end-user.

Kraus warrants the mechanical components such as but not limited to sprayhead assembly (includes engine, aerators, structure, restrictors, back flow preventers, sprayer hoses, braided supply line hoses which encompasses nylon, silicon and stainless steel,etc) of the product to be free from defects in material and workmanship under normal usage for a period of one (1) year. The warranty commences from the initial date of purchase by the owner or trade professional, from an authorized Kraus dealer, through the one (1) year term of the original owner or end-user.

Kraus warrants the mechanical component (cartridge) of the product to be free from defects in material and workmanship under normal usage for a period of five (5) years. The warranty commences from the initial date of purchase by the owner or trade professional, from an authorized Kraus dealer, through the five (5) year term of the original owner or end-user.

Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user, and is not transferable to a subsequent owner.

RESTRICTIONS

This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at discount outlets, unauthorized dealers, and/or sold on clearance.

This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance, alteration of the product, or failure to follow care or installation instructions enclosed with your product. Avoid using abrasive cleaners such as powders, bleach, ammonia, alcohol, or chlorine. Avoid using abrasive pads, steel wool, or wire brushes, as these will damage and wear down the finish.

This warranty does not apply to Products that have not been installed or operated in accordance with instructions supplied by Kraus and all applicable rules, regulations, and legislation pertaining to such installations.

This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade professional. Kraus insists that such professionals have experience in the installation of bathroom and kitchen manufactured goods.

This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does not allow recovery of incidental or consequential damages, such as loss of use, delay, property damage, or other consequential damages, and Kraus accepts no liability for such damages.

This warranty does not cover Marine or Outdoor Installation.

Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.

COMMERCIAL WARRANTY

Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use.

All incidental or consequential damages are specifically excluded. No additional warranties, express or implied are given, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

KRAUS USA has the right to change, modify, and/or update the warranty policy at any time. For the latest, most up to date comprehensive warranty, go to www.kraususa.com/warranty.

Download the Kraus Care & Maintenance Guide at: http://www.kraususa.com/maintenance

IMPORTANT

Register Your Kraus Product

Activate Your Warranty

Access Premium Customer Support

Get Product Information

REGISTER TODAY

ⓕ ? ⓟ ?

Kraus Kitchen Soap Dispenser

Models: KSD-31, KSD-32, KSD-43

INSTALLATION GUIDE

Congratulations on the purchase of your new Kraus plumbing fixture!

Please keep the box and packaging materials until your product is completely installed. If you have any questions, require technical assistance, or have any problems with your product:

Prior to Installation:

• Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at 800-775-0703 for a replacement.
• Pre-drilled hole size requirement: 1 1/4"
• Max countertop thickness: 2 1/2"

For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help:

Toll-Free: 800.775.0703 or customerservice@kraususa.com

The step-by-step guidelines in the installation instructions are a general reference for installing a Kraus Sink. Should there be any discrepancies, Kraus cannot be held liable. It is recommended to install all Kraus products by hiring a licensed professional.

Diagram and Parts List:

Diagram illustrating the Kraus Kitchen Soap Dispenser components. Labeled parts include: a. Pump, b. Dispenser Base (KSD-31, KSD-32, KSD-43), c. Washer, d. Mounting Nut, e. Dispenser Bottle.

Installation Steps:

Step 1 Disassemble soap dispenser.

Diagram showing the disassembly of the soap dispenser, with parts a through e separated. Arrows indicate upward and downward movement for separation.

Step 2

Install dispenser base (b) with washer attached into the hole in the countertop. Re-install washer (c) and mounting nut (d) on the dispenser base (b) from underneath the countertop. Tighten mounting nut (d) by hand.

Diagram showing the dispenser base (b) with washer being inserted into a countertop hole. Below the countertop, the washer (c) and mounting nut (d) are shown being attached. A curved arrow indicates tightening the nut.

Step 3

Screw the dispenser bottle (e) to the dispenser base (b) from underneath the countertop. Tighten as required. Fill the dispenser bottle (e) from the top with up to 17 ounces of soap.

Diagram showing the dispenser bottle (e) being screwed onto the dispenser base (b) from underneath the countertop. Another view shows the bottle being filled from the top.

Step 4

Reinsert pump (a) into dispenser base (b) from the top. Press the pump several times to make sure soap is evenly distributed.

Diagram showing the pump (a) being reinserted into the dispenser base (b) from the top. A 'Press' label and arrow indicate pressing down on the pump head, with soap droplets shown dispensing.

Kitchen Accessories Warranty

Kraus products are manufactured and tested to the highest quality standards by Kraus USA Inc. ("Kraus").

Kraus extends this warranty to the original purchaser for personal household use of the "Kitchen Accessories" in their original location. The warranty is non-transferable.

Kraus warrants the structure and finish of the product (Kitchen Accessories) to be free from defects in material and workmanship under normal usage for a period of one (1) years. The warranty commences from the initial date of purchase by the owner or trade professional, from an authorized Kraus dealer, through the one (1) year term of the original owner or end-user.

Any product reported to the authorized dealer or to Kraus as being defective within the warranty period will be repaired or replaced with a product of equal value at the option of Kraus. This warranty extends to the original owner or end-user, and is not transferable to a subsequent owner.

Restrictions

This warranty does not cover antediluvian, discontinued, or display products, whether such items are purchased at discount outlets, unauthorized dealers, and/or sold on clearance.

This warranty does not cover instances of negligence, misuse, abuse, improper installation, carelessness, accident, hard water or mineral deposits, exposure to corrosive materials, misapplication, damages caused by improper maintenance, alteration of the product, or failure to follow care or installation instructions enclosed with your product. Avoid using abrasive cleaners such as powders, bleach, ammonia, alcohol, or chlorine. Avoid using abrasive pads, steel wool, or wire brushes, as these will damage and wear down the finish.

This warranty does not apply unless the Kraus product is installed by a fully insured and licensed trade professional. Kraus insists that such professionals have experience in the installation of bathroom and kitchen manufactured goods.

This warranty does not cover labor charges or costs of removal and reinstallation of said product. This warranty does not allow recovery of incidental or consequential damages such as loss of use, delay, property damage, or other consequential damages, and Kraus accepts no liability for such damages.

This warranty does not cover Marine or Outdoor Installation.

Except as otherwise provided above, Kraus makes no warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose, or compliance with any code. Shipping charges will be covered for the first (1) year of the warranted replacement part or product (HI, AK, and Puerto Rico shipping charges may apply). International shipping fees are not included.

Commercial Warranty

Kraus extends the above warranty for a period of one (1) year to purchasers of products for industrial, commercial, and business use.

All incidental or consequential damages are specifically excluded. No additional warranties, express or implied are given, including but not limited to any implied warranty of merchantability or fitness for a particular purpose.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.