for OREI models including: HDS-FO-K, OREI,OREI,OREI,1x2,HDMI,Extender,Splitter,HDBaseT,4K,,Multiple,Over,Single,Cable,CAT6/7,4K@60Hz,4:4:4,HDCP,2.2,with,IR,Remote,EDID,Management,,HDR,-,Up,to,400,Ft,-,Loop,Out,-,Low,Latency,(UHD12-EXB400-K),B08NGHYPBQ,B0CHXKRPHK,B08KGWXJSG,B08KGVX81Q,B08H4ZDF9C,B08LMP8DHF,B0CGG6373J,B09R82SHZD,B092LCD3MP
OREI 1x2 HDMI Extender Splitter HDBaseT 4K, Multiple Over Single Cable CAT6/7 4K@60Hz 4:4:4 HDCP 2.2 with IR Remote EDID Management, HDR - Up to 400 Ft - Loop Out - Low Latency (UHD12-EXB400-K) : Electronics
HDS-FO-K User Manual (PDF) OREI OREI OREI,1x2,HDMI,Extender,Splitter,HDBaseT,4K,,Multiple,Over,Single,Cable,CAT6/7,4K@60Hz,4:4:4,HDCP,2.2,with,IR,Remote,EDID,Management,,HDR,-,Up,to,400,Ft,-,Loop,Out,-,Low,Latency,(UHD12-EXB400-K),B08NGHYPBQ,B0CHXKRPHK,B08KGWXJSG,B08KGVX81Q,B08H4ZDF9C,B08LMP8DHF,B0CGG6373J,B09R82SHZD,B092LCD3MP
Amazon.com: OREI 1x2 HDMI Extender Splitter HDBaseT 4K, Multiple Over Single Cable CAT6/7 4K@60Hz 4:4:4 HDCP 2.2 with IR Remote EDID Management, HDR - Up to 400 Ft - Loop Out - Low Latency (UHD12-EXB400-K) : Electronics
UHD12-EXB400-K 18Gbps HDMI 1x2 Splitter Follow us on Youtube and Facebook Over CAT6 Up To 400ft USER MANUAL www.orei.com Table of Contents Introduction 04 Features 05 Package Contents 05 Specifications 06 Operation Controls and Functions 08 EDID Mode 13 ASCII Commands 14 Application Example 19 Thank you for purchasing this product Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. Surge protection device recommended This product contains sensitive electrical components that may be damaged by electrical spikes, surges, electric shock, lightning strikes, etc. Use of surge protection systems is highly recommended in order to protect and extend the service life of your equipment. page 022 Registration Page Please Activate your warranty by registering our product through the link below - www.orei.com/register Technical Support Need Help? Our experienced Technical Support Team is here for you to answer your questions, give technical advice or help troubleshoot your project to get you installed on time and on budget. Call, email or chat with us now. OREI Live Technical Support Hours US team (US/Canada/Mexico): Monday-Friday, 9 a.m. - 6 p.m. Central Time Support Email - info@orei.com | Support Number - 877-290-5530 Caution The product requires the use of UTP connectors. Please connect in direct interconnection method and do not cross connect. White and Orange Orange White and Green Blue White and Blue Green White and Brown Brown Direct Interconnection Method page 03 Introduction The UHD12-EXB400-K can distribute 1 source signal to 2 displays up to 400ft, with video resolution up to 4K@60Hz 4:4:4. Features an HDMI loop output on the Transmitter to connect a display at the source. The HDMI signal can be extended up to 394ft/120m at the resolution of 4K@60Hz, or 492ft/150m at 1080P@60Hz via a single CAT6/6a/7 cable. Up to 7.1CH HD audio pass-through on the HDMI ports. Features Bi-directional IR and RS-232 control. Coax and analog audio outputs at the Transmitter to connect an external audio device. Power over Ethernet (PoE) function; only requires power supply at the Transmitter to power the whole setup. page 04 Features 1. HDMI 2.0b, HDCP 2.2 and HDCP 1.x compliant 2. 18Gbps video bandwidth 3 Video resolution up to 4K@60Hz 4:4:4 4. HDR, HDR10+, HLG and Dolby vision 5. Up to 7.1CH HD audio pass-through on the HDMI ports 6. Digital and analog audio output on the Transmitter. 7. Extend HDMI signal up to 394ft/120m at 4K@60Hz, 492ft/150m at 1080P@60Hz via a single CAT6/6a/7 cable. 8. HDMI loop output on the Transmitter to connect a display near the source. 9. Bi-directional IR, and RS-232 control 10. Advanced EDID management 11. One-way POE (Power Over Ethernet) function from Transmitter to Receiver. 12. Features HDBaseT Technology Package Contents 1× UHD12-EXB400-K 1. (Transmitter) 2. 2× HDBaseT Receiver 3. 3× IR Blaster Cable (1.5m) 4. 3× IR Receiver Cable (1.5m) 5. 3× 3pin-3.81mm Phoenix Connector (male) 6. 1× 5pin-3.81mm Phoenix Connector (male) 7. 6× Mounting Ear 8. 1× 24V/1A DC Locking Power Adapter 9. 12× Machine Screws (KM3*4) 10. 1× User Manual page 05 Specifications Technical HDMI Compliance HDMI 2.0b HDCP Compliance HDCP 2.2/1.x Video Bandwidth 594MHz/18Gbps Video Resolution 480i ~1080P@50/60Hz, 2K@24/30/60Hz, 4K@24/30/60Hz Color Depth 8-bit, 10-bit, 12-bit (1080p@60Hz) 8-bit (4K & 2K@60Hz YUV4:4:4) 8-bit, 10-bit, 12-bit (4K & 2K@60Hz YCbCr 4:2:2/4:2:0) Color Space RGB 4:4:4, YCbCr 4:4:4 / 4:2:2 / 4:2:0 HDR HDR, HDR10+, HLG, Dolby vision (Note: For Dolby vision, the local HDMI loopout supports 4K@60Hz, but the remote HDMI output only supports 1080P@60Hz.) LPCM 2.0/2.1/5.1/6.1/7.1, Dolby Digital, Dolby TrueHD, HDMI Audio Formats Dolby Digital Plus(DD+), DTS-ES, DTS HD Master, DTS HD-HRA, DTS-X Coaxial Audio Formats PCM 2.0, Dolby Digital / Plus, DTS 2.0/5.1 Analog Audio Formats PCM 2.0CH ESD Protection Human body model--±8kV (Air-gap discharge) & ±4kV (Contact discharge) Connection Transmitter Input: 1 × HDMI IN [Type A, 19-pin female] 1 × RS-232 [3-pin phoenix connector] 1 × IR IN [3.5mm stereo mini-jack] Output: 1 × HDMI LOOP OUT [Type A, 19-pin female] 2 × HDBT OUTPUT [RJ45] 1 × COAX AUDIO OUT [RCA] 1 × L/R AUDIO OUT [5-pin phoenix connector] 1 × IR OUT [3.5mm stereo mini-jack] page 06 Specifications Connection Receiver Input: 1× HDBT IN [RJ45, 8-pin female] 1 × IR IN [3.5mm Stereo Mini-jack] 1 × RS-232 [Phoenix jack] 1 × SERVICE [Mini-USB, Update port] Output: 1 × HDMI Type A [19-pin female] 1 × AUDIO OUT [3.5mm Stereo Mini-jack] 1 × IR OUT [3.5mm Stereo Mini-jack] Mechanical Housing Metal Enclosure Color Black Dimensions Transmitter: 170mm (L) × 130mm (W) × 40mm (H) Receiver: 140mm (L) × 65mm (W) × 18mm (H) Weight Transmitter: 689g/24.3oz Receiver: 155g/5.46oz Power Consumption 18W (Max) Power Supply Input: AC 100-240V 50/60Hz, Output: DC 24V/1A (US/EU standards, CE/FCC/UL certified) Operating Temperature 32~104°F / 0~40°C Storage Temperature -4~140°F / -20~60°C Relative Humidity 20~90% RH (Non-condensing) page 07 Operation Controls and Functions Transmitter: Front Panel IN LOOP 1 2 OUT 1 23 4 No. Name Function Description 1. Power LED When the device is powered on, the red power LED will turn on. 2. IN LED When an active source device is connected to the HDMI IN port, the green LED will turn on. 3. LOOP LED When an active display is connected to the HDMI LOOP OUT port, the green LED will turn on. When the HDBT OUTPUT 1/2 port is connected to the HD4. OUT(1~2) LED BaseT Receiver, the corresponding green LED will turn on. page 08 Operation Controls and Functions Transmitter: Rear Panel 1 23 4 5 TX RX RS-232 1 0 EDID IN OUT AUDIO OUT L+ R+ IR IN LOOP OUT HDMI 1 HDBT OUTPUT 2 ON OFF DC 24V 6 7 8 9 10 11 No. Name 1. RS-232 2. IR IN 3. IR OUT AUDIO OUT 4. (COAX, L/R) Function Description Connect to a PC or control system via a 3-pin phoenix connector cable for three functions: 1, Firmware update; 2, Control the Splitter via RS-232 commands; 3, RS-232 signal pass-through (from transmitter to receiver or from receiver to transmitter). Connect the IR receiver cable; the received signal will be emitted to the IR OUT port of the HDBaseT Receiver. Connect the IR blaster cable; it will transmit the signal received from the IR IN port of the HDBaseT Receiver. Coaxial/analog audio output port; connect an amplifier or speaker for audio. page 09 Operation Controls and Functions No. Name Function Description 5. Power switch Press this switch to power on/off the device. 6. EDID DIAL switch Used to set EDID mode. Please refer to "EDID Mode (Page 13)" for details. 7. HDMI port IN: HDMI input port; connect an HDMI source device such as DVD Player or set-top box with an HDMI cable. LOOP OUT: HDMI loop output port; connect an HDMI display such as TV or Monitor with an HDMI cable. 8. HDBT OUTPUT Connect to the HDBT IN port of the Receiver with a CAT port (1~2) cable. Link Signal 9. Indicator (Green) Illuminating: Transmitter and receiver are connected. Dark: Transmitter and receiver are not connected. Data Signal 10. Indicator (Orange) Illuminating: HDMI signal with HDCP. Flashing: HDMI signal without HDCP. Dark: No HDMI signal. 11. DC 24V Plug the DC 24V power supply into the unit and connect the adapter to an AC outlet. (Note: The Transmitter can power the Receiver via the CAT cable.) page 10 Operation Controls and Functions Receiver 1 SERVICE 2 DC 24V HDBT IN HDMI OUT AUDIO OUT IR IN IR OUT 3 54 6 7 8 9 10 11 No. Name Function Description 1. Power LED When the Receiver is powered on, the red power LED will turn on. 2. SERVICE port Used for firmware update. 3. DC 24V Plug DC 24V/1A power supply into the unit and connect the adapter to an AC outlet. (Note: The Receiver can be powered by the Transmitter via the CAT cable, so a separate power supply is not required.) 4. HDBT IN Connect to the HDBT OUTPUT port of the Transmitter with a CAT cable. Link Signal 5. Indicator (Green) When the Receiver is powered on, the power indicator will turn on. Data Signal 6. Indicator (Orange) Illuminating: HDMI signal with HDCP. Flashing: HDMI signal without HDCP. Dark: No HDMI signal. page 11 Operation Controls and Functions No. Name Function Description HDMI output port; connect an HDMI display such as TV or 7. HDMI OUT Projector with an HDMI cable. 8. AUDIO OUT Audio output port; connect to a speaker or soundbar. 9. IR IN Connect the IR Receiver cable. The IR signal will be sent to the IR OUT port of the Transmitter. 10. IR OUT Connect the IR Blaster cable. The IR signal will be received from the IR IN port of the Transmitter. 11. RS-232 3-pin Phoenix connector for RS-232 command transmission. The RS-232 command will pass-through from Transmitter to Receiver or from Receiver to Transmitter. IR Pin Definition IR Receiver IR Blaster IR Blaster Signal Power NC IR Receiver IR Signal IR Blaster Power Grounding Note: When the angle between the IR receiver and the remote control is ± 45 °, the transmission distance is 0-5 meters; when the angle between the IR receiver and the remote control is ± 90 °, the transmission distance is 0-8 meters. page 12 EDID Mode The defined EDID setting list of the product is shown below. 1 means "UP" and 0 means "DOWN" EDID Mode EDID Description 11111 1080P, Stereo 2.0 EDID Mode EDID Description 01111 4K/2K60Hz_444, Dolby/DTS 5.1 11110 1080P, Dolby/DTS 5.1 11101 1080P, HD Audio 7.1 11100 1080I, Stereo 2.0 11011 1080I, Dolby/DTS 5.1 11010 1080I, HD Audio 7.1 01110 4K/2K60Hz_444, HD Audio 7.1 01101 4K/2K60Hz_444, Stereo 2.0 HDR 01100 4K/2K60Hz_444, Dolby/DTS 5.1 HDR 01011 4K/2K60Hz_444, HD Audio 7.1HDR 01010 COPY_FROM_LOOP OUT 11001 1080P 3D, Stereo 2.0 01001 COPY_FROM_HDBT OUT1 11000 1080P 3D, Dolby/DTS 5.1 01000 COPY_FROM_HDBT OUT2 10111 1080P 3D, HD Audio 7.1 00111 1080P, Stereo 2.0 10110 4K/2K30Hz_444, Stereo Audio 2.0 00110 1080P, Stereo 2.0 10101 4K/2K30Hz_444, Dolby/DTS 5.1 00101 1080P, Stereo 2.0 10100 4K/2K30Hz_444, HD Audio 7.1 00100 1080P, Stereo 2.0 10011 4K/2K60Hz_420, Stereo Audio 2.0 00011 1080P, Stereo 2.0 10010 4K/2K60Hz_420, Dolby/DTS 5.1 00010 1080P, Stereo 2.0 10001 4K/2K60Hz_420, HD Audio 7.1 10000 4K/2K60Hz_444, Stereo Audio 2.0 00001 1080P, Stereo 2.0 00000 PC control mode page 13 ASCII Commands The product also supports ASCII command control. Connect the RS232 port of the product to a PC with a 3-pin phoenix connector cable. Then, open a Serial Command tool on the PC to send ASCII commands to control the product. The ASCII commands list is as below. ASCII Commands Serial port protocol. Baud rate: 115200 (default), Data bits: 8bit, Stop bits:1; Check bit: 0 x - Parameter 1; y - Parameter 2; ! - Delimiter Command Code Function Description Example Feedback Default Power s power z! Power on/off the device,z=0~1 (z=0 power off, z=1 power on) Power on System Initializing... s power 1! power on Initialization Finished! FW version x.xx.xx r power! Get current power state r power! power on/power off s reboot! Reboot the device s reboot! Reboot... System Initializing... Initialization Finished! FW version x.xx.xx page 14 ASCII Commands Command Function Description Example Feedback Code System Setting help! List all commands help! Default r type! Get device model r type! UHD12-EXB400-K r status! Get device current status r status! Get the unit all status: power, in/out connection, edid mode r fw version! r fw MCU BOOT: Vx.xx.xx Get Firmware version version! MCU APP: Vx.xx.xx r link in! Get the connection status of the input port r link in! HDMI IN: connect Get the connection status of the y output r link out y! port, y=0~3 (0=all, 1~2=HDBT 1~2, 3 = loop out) r link out 1! hdmi loop out: connect hdbt output 1: connect s reset! Reset to factory defaults s reset! Reset to factory defaults System Initializing... Initialization Finished! FW version x.xx.xx page 15 ASCII Commands Command Function Descrip- Code tion Example Output Setting s hdmi stream z! s hdmi hdcp z! Set hdmi loop output stream on/off s hdmi z=0~1 (0:disable,1:en- stream 1 ! able) Set hdmi loop output hdcp on/off s hdmi z=0~1 (0:disable,1:en- hdcp 1! able) s hdbt y hdcp z! Set hdbt output y hdcp on/off, y=0~2 (0=all) z=0~1 (0:disable, 1:enable) s hdbt 1 hdcp 1 ! s hdbt 0 hdcp 1 ! s hdbt y stream z! Set hdbt output y stream on/off, y=0~2 (0=all) z=0~1 (0:disable,1:enable) s hdbt 1 stream 1 ! s hdbt 0 stream 1 ! r hdmi stream! r hdmi hdcp! Get hdmi loop out stream status Get hdmi loop out hdcp status r hdmi stream! r hdmi hdcp! Feedback Default Enable hdmi loop out stream Disable hdmi loop out enable stream Enable hdmi loop out hdcp enable Disable hdmi loop out hdcp Enable hdbt output 1hdcp Disable hdbt output 1 hdcp Enable hdbt all outputs enable hdcp Disable hdbt all outputs hdcp Enable hdbt output 1 stream Disable hdbt output 1 stream Enable hdbt all outputs enable stream Disable hdbt all outputs stream Enable hdmi output stream Enable hdmi output hdcp page 16 ASCII Commands Command Code Function Description Output Setting r hdbt y hdcp! r hdbt stream! Get hdbt output y hdcp status, y=0~2 (0=all) Get hdbt output y stream status, y=0~2 (0=all) EDID Setting Example Feedback Default r hdbt 1 hdcp! r hdbt 1 stream! Enable hdbt output 1 hdcp Enable hdbt output 1 stream s edid in from z! Set input EDID from default EDID z, z=1~24 1, 1080p,Stereo Audio 2.0 2, 1080p,Dolby/DTS 5.1 3, 1080p,HD Audio 7.1 4, 1080i,Stereo Audio 2.0 5, 1080i,Dolby/DTS 5.1 6, 1080i,HD Audio 7.1 7, 3D,Stereo Audio 2.0 8, 3D,Dolby/DTS 5.1 9, 3D,HD Audio 7.1 10, 4K2K30_444, Stereo Audio 2.0 11, 4K2K30_444,Dolby/DTS 5.1 12, 4K2K30_444,HD Audio 7.1 13, 4K2K60_420, Stereo Audio 2.0 s edid in from 1! 14, 4K2K60_420, Dolby/DTS 5.1 15, 4K2K60_420,HD Audio 7.1 16, 4K2K60_444, Stereo Audio 2.0 17, 4K2K60_444, Dolby/DTS 5.1 18, 4K2K60_444,HD Audio 7.1 19, 4K2K60_444, Stereo Audio 2.0 HDR 20, 4K2K60_444, Dolby/DTS 5.1HDR 21, 4K2K60_444, HD Audio 7.1 HDR 22, copy from hdmi loop out 23, copy from hdbt output 1 24, copy from hdbt output 2 input EDID:1080p, Stereo Audio 2.0 Please toggle EDID dip switch 1080p, Stereo Audio 2.0 to 00000! page 17 ASCII Commands Command Code Function Description Example Feedback EDID Setting s edid user1 00 FF FF FF FF ...! r edid user1! r edid in! r edid in data! Set user1 EDID data s edid user1 user1 EDID data: 00 00 ff ff ff ff .... ! FF FF .... Get user1 EDID data r edid user1! user1 EDID data : 00 FF FF FF FF FF FF 00 ......... Get EDID status of the input r edid in! input EDID: 4K2K60_ 444, Stereo Audio 2.0 Get the EDID data of the r edid in EDID data : 00 FF FF hdmi input data! FF FF FF FF 00 ...... RS-232 BYPASS Setting s rs232 bypass hdbt y! r rs232 bypass! s device baud w size x stop y parity z! s rs232 time x! Set RS-232 port connect to HDBT out1 Receiver s rs232 by- RS-232 port, y=0~3 ( 0=all, 1~2= hdbt out 1~2, pass hdbt 1! 3=NC) Get RS-232 port connect r rs232 to HDBT out receiver RS-232 port bypass! Set receiver control device COM port setting, w=2400, 4800, 9600,19200,38400, 57600,115200, x=7,8 y=1,2, z=none, ven, odd Set send RS232 command wait time x=200~5000ms s device baud 57600 size 8 stop 1 parity none! s rs232 time 200! RS-232 connect to HDBT OUT1 RS-232 not connect to HDBT OUT RS-232 connect to HDBT OUT1 RS-232 connect to all HDBT OUT RS-232 not connect to HDBT OUT receiver device COM port setting baudrate: 57600 data size: 8, stop:1 parity: none send RS-232 command wait time 200ms Default y=0 200ms page 18 Application Example IR Receiver PC Amplifier IR Blaster 2.0 Speakers TX RX RS-232 1 0 EDID Transmitter IN OUT AUDIO OUT L+ R+ IR IN LOOP OUT HDMI 1 HDBT OUTPUT 2 LAN ON OFF DC 24V TV DVD or Blu-ray Player DC 24V HDBT IN LAN Power Supply CAT6/6a/7 Receiver HDMI OUT AUDIO OUT IR IN IR OUT 2.0 Speakers IR Receiver HDMI Matrix with RS-232 function TV IR Blaster The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. page 19 18Gbps HDMI 1x2 Splitter Over CAT6 Up To 400ft UHD12-EXB400-K www.orei.com © 2023