Philips LEDtube Installation Guide
An Energy-Saving Alternative
Introduction
This document provides installation instructions for Philips LEDtubes, designed as an energy-saving alternative to traditional fluorescent lighting.
Please read these instructions carefully before proceeding with the installation.
Note: Information may not be valid in Germany, Austria, and Switzerland.
Packing List
Each package contains: Philips LEDtube: 10 pcs
Safety Symbols and Meanings
- Symbol: [No smoking symbol]
Meaning: DO NOT USE WITH DIMMERS ? - Symbol: [Crossed-out water droplet, crossed-out person]
Meaning: NEED TO BE USED IN DRY CONDITIONS OR IN A LUMINAIRE THAT PROVIDES PROTECTION ?
General Warnings and Suitability
This lamp is not suitable for use in emergency luminaires designed for double-capped fluorescent lamps.
This lamp may not be suitable for all applications where traditional fluorescent lamps were used. Its temperature range is more restricted. Consult the manufacturer if unsure about application suitability.
This lamp is designed for general lighting service and is not intended for environments with explosive atmospheres.
The Philips LEDtube is not dimmable.
It is developed for G5 sockets, complying with IEC Standard.
The LEDtube is not suitable for direct current (DC) operation.
It is suitable for operation on mains voltage without a ballast, provided the luminaire is specifically designed for LED tubes on mains voltage. No modification to such luminaires is necessary.
If replacing a traditional fluorescent lamp, verify that the required illuminance levels according to regulations are met.
LEDtubes are intended for general lighting applications only.
The lamp must only be used in dry environments and with a luminaire approved for the specific application area.
Please adhere strictly to these installation instructions.
For any questions, refer to the product data sheets or contact the manufacturer directly.
Always switch off the power supply before commencing work! ⚠️
Installation Steps (Translated)
- Turn off the mains voltage.
- Remove the existing fluorescent lamp.
- Disconnect the ballast.
- Philips LEDtubes connect on one side only.
- Insert the lamp into the sockets.
- Rotate the lamp 90 degrees.
- Turn on the mains voltage.
Wiring Diagrams Explained
Double-sided wiring diagram
This diagram illustrates the connection of a Philips LEDtube to a luminaire requiring a double-sided connection. It shows the process of bypassing the traditional starter and ballast, and connecting the LEDtube directly to the mains voltage via a High-Frequency (HF) ballast. The steps involve powering off, removing the old tube, disconnecting the ballast, connecting the LEDtube, ensuring correct seating, and powering on.
Single-sided wiring diagram
This diagram details the installation of a Philips LEDtube in a luminaire where only one side of the tube is connected to the mains voltage. This typically involves bypassing or removing the existing ballast and starter, and connecting the LEDtube directly to the power supply on one end. The steps are similar to the double-sided diagram: power off, remove old tube, disconnect ballast, connect LEDtube, ensure seating, and power on.
Professional Installation Recommended
Philips LED tubes should be installed by qualified professionals in accordance with relevant codes and regulations.
Waste Disposal and Environmental Responsibility
Please familiarize yourself with local regulations for the disposal, separation, and collection of electrical and electronic products and packaging. Do not dispose of old products with regular household waste.
Proper disposal of packaging, products, and batteries helps prevent negative environmental and health impacts. Batteries must be disposed of separately through designated collection facilities.
Products with non-user replaceable batteries require professional removal of these batteries during disposal.
For detailed information on product and battery disposal, visit www.signify.com/sustainability.
Product and Legal Information
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V., used under license.
© 2022 Signify Holding. All rights reserved.
Reproduction of this document, in whole or in part, is prohibited without the prior written consent of the copyright owner.
The information provided herein is believed to be accurate and reliable but may be subject to change without notice. The publisher accepts no liability for any consequences arising from its use.
Publication of this information does not grant any license under patent or other industrial or intellectual property rights.
Document Version: 10/2022
Visit us at: www.philips.com/lighting
Energy Efficiency Label
The document includes an energy efficiency label for lamps, graded from A++ (most efficient) to G (least efficient). The specific lamp depicted on this label is rated 'A' for energy efficiency, indicated by a filled bar in the 'A' category.
