Installation Guide for iBoard models including: IB-362C Running Boards Nerf Bars Side Steps Step Bars, IB-362C, Running Boards Nerf Bars Side Steps Step Bars, Nerf Bars Side Steps Step Bars, Steps Step Bars, Bars
Auto Parts & Auto Accessories - Over 4000 Auto Parts, Aftermarket Parts, Truck Accessories & Car Accessories
PART#: IB-P552Y&H iBoard® Series READ INSTRUCTIONS CAREFULLY BEFORE START ING INSTALLATION. REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. ASSISTANCE IS RECOMMENDED. *ROCKER PANEL MOUNT *NO DRILLING REQUIRED Fastener Size Tightening Torque (ft-lbs) 6mm 6-7 8mm 16-18 10mm 31-32 12mm 56-58 14mm 92-94 Required X X X PART LIST Driver Side Step Bar Front Passenger Side Step Bar Driver Front/ Center Mounting Bracket (DFM/ DCM) Passenger Front/ Center Mounting Bracket (PFM/ PCM) (DFM/DCM) (PFM/PCM) Driver Rear Mounting Bracket (DRM) Passenger Rear Mounting Bracket (PRM) Customer Support: info@iboardauto.com 1 Rev. 20241201 Hardware Package A (For Bracket Installation) Item QTY Description Item QTY Description 1# 6 M10X1.5-30mm Hex Bolts 5# 12 M8X1.25-25mm Hex Bolts 2# 6 M10 Large Flat Washers 6# 24 M8 Large Flat Washers 3# 6 M10 Lock Washers 7# 12 M8 Lock Washers 4# 6 M10 Clip Nuts 8# 12 M8 Hex Nuts 1 # 2 # 3 # 4 # 5 # 6 # 7 # 8 # Item QTY Hardware Package B (For Step Bar Installation) Description Item QTY Description 1# 12 M8X1.25-35mm Carriage Bolts 2# 12 M8 Large Flat Washers 3# 12 M8 Nylon Lock Nuts 4# 6 Sliders (Packed with Mounting Brackets) 1 # 2 # 3 # 4 # Customer Support: info@iboardauto.com 2 Rev. 20241201 STEP 1 Start installation from the passenger side front of the vehicle, temporarily remove the plastic side panel. Move to the floor panel, locate the square hole and (2) round holes in the pinch weld, (Fig 1). M10 Clip Nut Front Front (Fig 2) Attach The M10 Clip Nut (2) M8X1.25-25mm Hex Bolts (4) M8 Large Flat Washers (2) M8 Lock Washers (2) M8 Hex Nuts (Fig 1) Passenger Side Front Mounting Location STEP 2 Insert (1) M10 Clip Nut into the square hole on the floor panel, and line up the nut with the round hole, (Fig 2). Attach (1) Passenger Front Mounting Bracket to the installed M10 Clip Nut with (1) M10X1.5-30mm Hex Bolt, (1) M10 Lock Washer and (1) M10 Flat Washer, (Figs 3-4). Do not fully tighten hardware at this time. STEP 3 Attach the Passenger Front Mounting Bracket to the pinch weld with (2) M8X1.25-25mm Hex Bolts, (4) M8 Flat Washers, (2) M8 Lock Washers and (2) M8 Hex Bolts, (Figs 3-4). Do not fully tighten hardware at this time. (1) M10 Clip Nut (1) M10X1.5-30mm Hex Bolt (1) M10 Large Flat Washer (1) M10 Lock Washer (Fig 3) Passenger Front Mounting Bracket Installation Front (Fig 4) Passenger Front Mounting Bracket Installation Customer Support: info@iboardauto.com 3 Rev. 20241201 STEP 4 Move to the Passenger Side Center & Rear Mounting Locations, (Fig 5 & 6). Repeat Steps 1-3 to attach the Passenger Center & Rear Mounting Brackets to the vehicle. Do not fully tighten hardware at this time. Note: (3) Passenger Front & Center & Rear Mounting Brackets are universal. Front (Fig 5) Passenger Side Center Mounting Location STEP 5 Once all (3) Passenger side mounting brackets are installed, then proceed to the Step Bar installation. (Figs 7 & 8) (1) Select (1) Slider and (2) M8X1.25-35mm Carriage Bolts; (2) Install (2) M8X1.25-35mm Carriage Bolts in (1) Slider. (3) Slide the Slider (with carriage bolts) to the Step Bar. (4) Repeat to install the other (2) sliders to the step bar. (5) Attach the Step Bar (with the Sliders) onto the installed mounting brackets. Position the Sliders to the installed brackets. Secure the Step Bar to the installed Brackets by using (6) M8 Large Flat Washers and (6) M8 Nylon Lock Nuts and (3) Sliders, (Fig 8). Do not fully tighten hardware at this time. Note: The Sliders are packed with the Mounting Brackets. Level and adjust the Step Bar and fully tighten all hardware. Repeat Steps 1-5 for the other side Step Bar installation. The installation is completed!!! Attention Do periodic inspections to the installation to make sure that all hardware is secure and tight. In order to protect your bars/boards, please use mild soap/non-abrasive products for cleaning only. Front (Fig 6) Passenger Side Rear Mounting Location Customer Support: info@iboardauto.com 4 Rev. 20241201 Slider (2) Carriage Bolts (Fig 7) Slider Installation Slider with (2) Carriage Bolts Step Bar Slider (w/ installed Carriage Bolts) Step Bar (Bottom View) Mounting Bracket (2) M8 Large Flat Washers (2) M8 Nylon Lock Nuts (Fig 8) Step Bar Installation Customer Support: info@iboardauto.com 5 Rev. 20241201Microsoft Publisher 2016