NAVEE Electric Scooter

1. Assembly

Put down the kickstand, and hold up the stem until it is completely in an upright position. Then push the quick release lever inward to the end.

Install the handlebar onto the stem, and make sure to install the handlebar in the correct direction. Follow the number order as illustrated to pre-tighten the four screws with the included Allen key. Make sure the handlebar is correctly installed and then tighten the screws thoroughly.

(Illustration: Diagram showing the assembly steps for the scooter's stem and handlebar, including torque specifications.)

2. Charging

The scooter is fully charged when the LED on the battery charger changes from red to green.

WARNING: Do not charge non-rechargeable batteries. Use only with T2345-BD5A battery. Use only with NBW54D601D3D power supply unit. Charge your scooter indoors, and never expose it to rain.

When the scooter is turned off for about a month with the battery level lower than 30%, it will enter sleep mode. To exit sleep mode, charge the scooter for about three seconds to activate the battery.

(Illustration: Diagram showing the charging process with a battery indicator showing less than 30% and a charging icon.)

3. Connect to the NAVEE App

For your safety, your new scooter cannot be fully activated before it is linked to your mobile phone. It will beep continuously after being turned on and its speed will be limited to 10 km/h. When the scooter is used for the first time, it must be activated via the NAVEE app, where you can follow a safety tutorial. After activation, the beeping will stop and the speed restriction will be lifted.

Scan the QR code to download and install the App, then you can register/login.

(Illustration: Two QR codes labeled 'Google Play' and 'iOS' for app download.)

4. Apple's Find My network

Open the NAVEE app, click on [Link my device] and follow the instructions to link your scooter.

Power on the scooter; a blinking Bluetooth icon indicates the scooter is waiting to be connected.

To pair your scooter with Find My: Press the power button, squeeze the brake lever, and simultaneously press the accelerator 3 times to enter Find My pairing mode. You will hear a beep to proceed. Enable "Find My" on your iPhone or iPad, tap "+", select "add another item", and click "Connect" when "NAVEE Electric Scooter" is found. Follow the app instructions to complete the settings. A beep indicates successful pairing.

Notes:

• Exit the NAVEE app before using Find My.
• If Bluetooth proximity unlock is enabled, disable it and check if your phone's Bluetooth is paired with the scooter. If paired, unpair it before proceeding.

To unpair: Turn on the scooter, ensure it's not locked or charging. Squeeze the brake lever and press the accelerator 5 times. When the display turns off, the scooter is reset to factory settings and cannot be found by the Find My app. To re-pair, delete the scooter from the Find My app and pair again.

To find the serial number: Press the accelerator and squeeze the brake lever 3 times to activate the serial number search function. The serial number will be displayed in the Find My app (for iOS users).

(Illustration: Diagram showing the scooter's handlebar with controls and a smartphone screen displaying the 'Link my device' option.)

5. Starting & Accelerating & Decelerating & Braking

Before riding, wear helmets, hand/wrist pads, knee pads, elbow pads, and other protective gear at all times.

Step on the deck with one foot, and slowly kick off the other on the ground. When the scooter starts to coast, put both feet on the deck and gently press the accelerator. The motor will not start until the speed reaches 5 km/h.

To slow down, release the accelerator. To brake, press the brake lever.

(Illustration: Diagram showing a person wearing protective gear and riding the scooter, with a speed indicator showing V≥5 km/h.)

6. Parking

When the scooter slows down or stops, put one foot on the ground to get off. Put down the kickstand when parking.

PARKING WARNING:

• Do not park your kick scooter on a slope.
• Make sure the kickstand is positioned on a flat surface.

(Illustration: Diagram showing how to park the scooter, including putting down the kickstand.)

Scan the QR code to access electronic user manuals.