FIBARO CO Sensor FGBHCD-001 Operating Manual

Introduction

This document is the operating manual for the FIBARO CO Sensor (FGBHCD-001), a HomeKit-enabled carbon monoxide detector designed to detect the presence of carbon monoxide (CO) gas at an early stage to prevent poisoning. It features a built-in siren, LED indicator, and temperature sensor, and integrates with Apple HomeKit technology.

The device uses Bluetooth low energy technology for wireless communication. It is wall-mounted and battery-powered.

Visual Indicator: The device displays visual cues such as 4 red LED blinks and 4 beeps, accompanied by the instruction "MOVE TO FRESH AIR!".

Compatibility: Works with Apple HomeKit.

Important Safety Information

General Carbon Monoxide Information

Carbon monoxide (CO) is a colourless, odourless, and tasteless poison gas that can be fatal when inhaled. It is produced when liquid, solid, or gas fuel is burned.

Symptoms of Carbon Monoxide Poisoning

Early symptoms can be confused with flu-like symptoms: headache, dizziness, and nausea. Breathing CO can cause sleepiness, vision problems (including blurred vision), ringing in the ears, aching arms and legs, irregular breathing, fatigue, and confusion. At very high levels, it causes loss of consciousness and death.

External factors such as exposure to basic (non-acidic) gases, silicone vapors, hydrogen sulfide or sulfuric acid gas, organic vapors, contact with water, dust and oil mist, or dew condensation may affect the device's reliability.

This device may not protect from long-term exposure to low levels of CO, which can also lead to neurological symptoms. It is not a substitute for appropriate ventilation and exhaust systems.

This product is not a toy. Keep away from children and animals!

Risk of malfunction exists if the device is tampered with.

Installation Guidelines

• The device should be installed below the ceiling level.
• The accessory should be installed on the wall, at least 30 cm (1 ft) away from the corners.
• The accessory should not be installed: in a bathroom, next to heat sources, within range of children, obstructed from possible carbon monoxide sources, or in direct sunlight.
• The accessory should be installed by a qualified installer.
• Do not paint the device.
• Clean the accessory with a slightly damp cloth or moistened tissue.
• Replace the device before the date indicated on the front or if a sensor error is detected.

If there is any question as to the cause of an alarm, it should be assumed that the alarm is due to a dangerous level of carbon monoxide and the dwelling should be evacuated.

HomeKit Technology

Apple HomeKit technology provides an easy, secure way to control HomeKit-enabled accessories using Siri on your iPhone, iPad, or iPod touch.

After installing your FIBARO CO Sensor, configure it from a compatible app with just a few simple steps. You can even create your own custom scenes to control your home settings. For example, you can create a scene to automatically turn off the lights, lock your doors, close the garage door, and set the thermostat to the desired temperature in just one step.

#1: Description and Features

The FIBARO CO Sensor is a HomeKit-enabled carbon monoxide detector using Bluetooth low energy technology. Its high sensitivity allows it to detect the presence of carbon monoxide (CO) gas at the early stage in order to prevent carbon monoxide poisoning.

The alarm is signaled with a built-in siren, a blinking LED indicator, and by sending information to your iOS device. Additionally, the accessory is equipped with a temperature sensor.

Main Features of FIBARO CO Sensor:

• Compatible with Apple HomeKit technology
• Bluetooth low energy technology for wireless communication
• Detects tampering when the casing is opened
• Wall-mounted
• Battery-powered
• Alarm signaled with a built-in siren and LED diode
• Built-in temperature sensor measuring ambient temperature

#2: Powering the Accessory

Steps to Power the Device:

1. Turn the cover counter-clockwise. [Diagram shows the circular device body]
2. Take off the cover. [Diagram shows the device body with the cover removed]
3. Remove the paper strip protecting the battery. [Diagram shows the battery compartment with a paper strip to be pulled out]
4. Proper powering up will be confirmed with a short beep. ? [Short beep]
5. Pair the accessory if you want to use it with HomeKit.

#3: Pairing the Accessory

Follow these steps to pair the FIBARO CO Sensor with your iOS device via HomeKit:

1. Open the Settings app on your iOS device.
2. Go to the Bluetooth section and turn Bluetooth on.
3. Place the accessory next to your iOS device.
4. Open a HomeKit compatible app on your iOS device.
5. Open the pairing window in your HomeKit app to detect available accessories.
6. Choose "CO Sensor" you wish to pair.
7. The CO Sensor will blink green to help you identify it.
8. Find the HomeKit Setup Code on the last page of the Quick Start Guide included in the box. It looks like: XXX-XX-XXX.
9. Start pairing with your HomeKit app.
10. Point your iOS device's camera at the Setup Code to scan it, or enter the Setup Code manually.
11. If the entered Setup Code is valid, the device will complete the setup process.
12. Follow any additional instructions displayed in the application.

#4: Physical Installation

• The accessory should be installed below the ceiling level.
• The accessory should be installed on the wall, at least 30 cm (1 ft) away from the corners.
• The accessory should not be installed: in a bathroom, next to heat sources, within range of children, obstructed from possible carbon monoxide sources, or in direct sunlight.
• The accessory should be installed by a qualified installer.
• Do not paint the device.
• Clean the accessory with a slightly damp cloth or moistened tissue.

Place of Installation:

A diagram illustrates ideal placement. The ceiling is at the top. A "NOT HERE" zone is indicated below the ceiling, marked with a cross symbol (❌). An "HERE" zone is indicated on the wall, 30 cm (1 ft) from the ceiling, marked with a checkmark symbol (✔️). The floor is at the bottom, with a recommended wall installation height of 1.5m (5ft) from the floor.

Installation on the Wall:

1. Mount the cover on a wall. [Diagram shows the circular cover plate being attached to the wall with screws.]
2. Attach the accessory to its cover. [Diagram shows the main sensor unit being attached to the mounted cover plate.]
3. Turn the accessory clockwise to close it. [Diagram shows the fully assembled unit attached to the wall.]

#5: Operating the Device

The menu allows performing different actions. To use the menu:

1. Press and hold the button for 3 seconds. ? [Button]
2. You should hear a short signal while the LED diode blinks white.
3. Release the button.
4. Wait for the device to indicate the desired menu position with a color:
   • White: confirms the start of the firmware update process.
   • Green: [Status indication]
   • Magenta: resets the CO peak value.
   • Yellow: initiates the device reset.
5. Press the button to confirm the selection.

Resetting the Accessory to Factory Defaults:

This procedure restores the accessory to its factory settings, including HomeKit pairing. Stored carbon monoxide and temperature measurements are not deleted.

1. Press and hold the button.
2. Release the button when the LED indicator glows white and a short beep sounds.
3. Click the button when the LED indicator glows yellow.
4. After a few seconds, the device will be reset (confirmed by a red LED indicator and a long beep).

Self-Test:

The self-test checks the operation of the accessory.

To start the self-test:

1. Press and hold the button.
2. The LED indicator will glow white, and you will hear a short beep.
3. Release the button when you hear the first alarm sequence.
4. Move away from the accessory to protect your hearing.

#6: Functionality

Carbon Monoxide Alarm:

The CO Sensor alarms about abnormal levels of carbon monoxide concentration with 4 red blinks and 4 loud beeps (every 5 seconds). The alarm is also reported to your iOS device.

Carbon Monoxide Measuring and Storing:

The CO Sensor measures carbon monoxide concentration and reports it. If the measured value differs from the previously reported value by at least 1 ppm, the accessory reports it to your iOS device. The last 2500 measurements are stored in non-volatile memory and can be accessed via the FIBARO for HomeKit app.

Temperature Measuring:

The CO Sensor measures ambient temperature every 30 seconds. If the measured temperature differs from the previously reported value by at least 1°C (1.8°F), the accessory reports it to your iOS device. The last 2500 measurements are stored in non-volatile memory and can be accessed via the FIBARO for HomeKit app.

Tamper Detection:

The CO Sensor detects tampering when the accessory is removed from its base and reports it to your iOS device. Tampering is indicated with one white blink and beep.

Battery Level Measuring:

The CO Sensor measures battery level every 6 hours and reports it to your iOS device. If the battery level is below 15%, the accessory will report low battery status and indicate it with one yellow blink and beep.

#7: Visual Indications & Acoustic Signals

The CO Sensor is equipped with a LED diode and a buzzer, signaling menu position and status of the accessory.

Accessory Status Indications:

#8: Battery

The FIBARO CO Sensor can be powered with a CR123A (included) battery. Estimated battery life with accessory on default settings is 3 years (tested with Panasonic Industrial Lithium).

Checking Battery Level:

The CO Sensor measures battery level every 6 hours and reports it to your iOS device. If the battery level is below 15%, the accessory will report low battery status and indicate it with one yellow blink and a short beep.

Replacing the Battery:

1. Remove the accessory from the cover by turning it counter-clockwise.
2. Pull the paper strip to take out the battery.
3. Press and hold the button for at least one second.
4. Insert a new CR123A battery, observing the polarities shown inside.
5. Attach the accessory to its cover by turning it clockwise and perform the test (as described in #5: Operating the device).
6. Launch your HomeKit app and swipe down to refresh the device state.

#9: Specifications

#10: Regulations

Legal Notices

All information, including but not limited to, information regarding features, functionality, and/or other product specifications are subject to change without notice. Fibaro reserves all rights to revise or update its products, software, or documentation without any obligation to notify any individual or entity.

FIBARO and Fibar Group logo are trademarks of Fibar Group S.A. Apple, iPhone, iPad, iPad Air, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries. HomeKit is a trademark of Apple Inc.

The Bluetooth word mark is a registered trademark of Bluetooth SIG, Inc. All other brands and product names referred to herein are trademarks of their respective holders.

Use of the "Works with Apple HomeKit" logo means that an electronic accessory has been designed to connect specifically to iPod touch, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Warning

This product is not a toy. Keep away from children and animals!

Information according REACH

The included Panasonic CR123A battery contains 1,2-Dimethoxyethane substance. Normal use of the device does not expose the user to this substance.

Declaration of Conformity

CE mark: Fibar Group S.A. declares that the device is in compliance with Directives 2014/53/EU and 2011/65/EU, 2015/863. The full text of the EU declaration of conformity is available at the following internet address: manuals.fibaro.com

WEEE Directive Compliance

Device labelled with this symbol ♻️ should not be disposed of with other household wastes. It shall be handed over to the applicable collection point for the recycling of waste electrical and electronic equipment.