Prior Information
These instructions apply to all Sonesse2 40 PoE drives. PoE = Power Over Ethernet.
Field of Application
The Sonesse 40 drives are designed to motorise interior blinds, and interior venetian blinds with a bottom bar that moves solely by gravity, with a mass less than 15 kg.
Liability
Before installing and using the drive, please read these instructions carefully. In addition to these instructions, comply with the attached Safety Instructions document. The drive must be installed by a home motorisation and automation professional, in accordance with Somfy's instructions and applicable regulations. Any operation outside the described field of application is prohibited and absolves Somfy of liability and invalidates the warranty. The installer must inform customers of operating and maintenance conditions and provide them with the relevant instructions. After-Sales Service must be performed by a professional. Always check product compatibility before installation. For more information, contact a Somfy representative or visit www.somfy.com.
Installation
[WARNING] These instructions are mandatory for the professional installer. Comply with current standards and legislation.
[CAUTION] Never drop, knock, puncture, or immerse the drive. Install an individual control point for each drive. Minimize gaps between the drive, accessories, tube, and end piece for silent operation. Never cut or remove the cable label.
Assembly
Replace the head cover with a different color (Optional)
The head cover is interchangeable to match the fabric color. To replace: 1. Unclip the cover. 2. Clip the new cover onto the head.
Preparing the drive
[CAUTION] The Sonesse2 40 PoE requires a tube interior diameter of Ø37 mm or greater. The crown is mandatory.
1. Fit the accessories required to integrate the drive into the tube: Fit the crown (a) and the wheel (b) to the drive.
2. Measure the length (L) between the inner edge of the drive head and the rim of the wheel.
Preparing the tube
1. Cut the tube to the required length.
2. Deburr the tube and remove any debris.
Assembling the drive-tube
1. Slide the drive into the tube. For tubes with a smooth interior, position the notch on the crown.
2. The wheel must be locked in place to prevent any movement in the tube. This can be achieved by fastening the tube to the wheel using self-tapping screws or steel pop rivets (placed between 5 mm and 15 mm from the outer edge of the wheel), or by using a wheel lock for non-smooth tubes.
[CAUTION] Screws or pop rivets must only be fastened on the wheel, not on the drive.
Installing the drive-tube assembly
[CAUTION] The motorized product must not be compressed between the brackets. Do not use the plastic cross without the metal bracket adapter.
The drive can be fixed directly onto the drive bracket using 2 screws (3.5 x 9 mm) with a manual tightening torque of 1 Nm. Drive plates are also available; use the 2 screws (3 x 6 mm) provided with the motor plate, with a manual tightening torque of 0.6 Nm.
1. Screw the bracket adapter to the drive head.
2. Install and fix the drive-tube assembly onto the end bracket (c) and onto the drive bracket (d).
[CAUTION] Do not let the tube hang by the head side only. Ensure the drive-tube assembly is secured onto the end bracket to prevent it from coming out. Minimize light gap and be careful not to pinch the cable or have it contact moving parts.
Wiring
[PRECAUTION] Cables routed through a metal wall must be protected and insulated. Secure cables to prevent contact with moving parts. The drive cable is not removable; if damaged, return the drive to After-Sales.
[CAUTION] Leave the power supply cable accessible for easy replacement. Always make a loop in the power supply cable to prevent water entry. External power supply is not provided by Somfy. Power supply must be installed indoors only, within a maximum ambient temperature of 40°C (104°F). Wiring must comply with the National Electric Code (NEC) and relevant local codes. Interconnection wiring may not be provided by Somfy.
Connect the PoE drive to the PoE switch.
[NOTICE] Use only a compatible switch. Check the power delivered by the switch. A female-to-female connector and Cat 5e (mini) extension cable can be used if needed. Maximum length between switch and drive is 100 m (330 feet).
Commissioning
Commissioning is done via:
- WebGUI (for individual drive settings): Use a web browser on a computer, tablet, or smartphone connected to the network. Enter the drive's Hostname (on the label) in the address field and follow instructions.
- PoE Config Tool (for discovering multiple drives): Download the program from https://www.somfy.com/projects/downloads. A certificate and API are required for product integration. Request information at https://www.somfypro.com/partner-with-us. (*For Android versions <13, enter the IP address.)
Tips and advice on installation
Questions about the product?
| Observations | Possible causes | Solutions |
|---|---|---|
| The motorised product does not work. | Wiring is incorrect. | Check the wiring and modify it if necessary. |
| The drive is in thermal protection mode (LED Red = ON then OFF). | Wait for the drive to cool down. Note that the drive will be hot. Do not touch it. | |
| An incorrect extension cable has been used. | Check the extension cable (Cat 5e mini). | |
| End-limits are not properly adjusted. | Adjust the end-limits. | |
| The motorised product is noisy. | The wheel and the crown are not adapted to the used tube. | Change the wheel and the crown. |
| The mechanical plays between drive, accessories, tube and end of tube are too high. | Decrease the plays between drive, accessories, tube and end of tube to the minimum. | |
| The wheel is not properly fixed to the tube. | Fix the wheel properly to the tube. | |
| The equipment is constrained between the brackets. | Decrease the constraint between the brackets. | |
| The length of the notch is not adapted to the drive hook or to the used crown. | Adapt the length of the notch to the drive hook or the used crown. | |
| Debris, screws or other are in the tube. | Empty the tube. | |
| The temperature of the environment is not in conformity with the operating temperature. | Change the environment temperature. | |
| The motorised product stops too soon or too late. | The end limits of the motorised product slip. | Re-set the end limits. |
| The motorised product does not fall within the recommended weight limits. | Check the compatibility of the motorised product. Consult a Somfy contact or visit www.somfy.com. |
Use and Maintenance
[NOTICE] This drive requires no maintenance operations. No user-serviceable parts.
Operation
To control the drive, refer to the installation instructions of the control point used.
PROG button
| Action | Button Press |
|---|---|
| User mode control (Up/Stop/Down/Stop) | Short press (< 1.5 s) |
| Send a DHCP request | Press until first feedback (approx. 2 s) |
| Force IP assignment method to DHCP | Press until second feedback (approx. 7 s) |
| Reset drive to factory mode | Press until third feedback (approx. 12 s) |
LED feedback
| LED Color | Feedback | Possible Causes |
|---|---|---|
| Green | Light fixed ON for 2 s at Power ON. | Power is ON. |
| Orange | Light ON then light OFF shortly. | Bus communication (may be disabled). Drive not set. |
| Light fixed ON. | Push IP address to the network. | |
| Blinks 2 times. | The drive has detected an obstacle. | |
| Red | Light fixed ON. | Thermal protection has been activated. Wait a few minutes. The drive may be hot. Do not touch it. |
| Light ON then light OFF: blinks regularly (1 s). | Drive position is out of limits. | |
| Blinks 2 times. | Setting is impossible. | |
| Flashes in 3 sets of 3 blinks. | Not connected to the network. No IP address. | |
| Blinks regularly (0.3 s) |
Tips and advice on operation
Questions about the drive?
| Observations | Possible Causes | Solutions |
|---|---|---|
| The motorised product does not work. | The drive is in thermal protection mode. | Wait for the drive to cool down to restart. Note that the drive will be hot. Do not touch it. |
[NOTICE] If the motorised product still does not work, contact a drive and home automation professional.
Technical Data
| Parameter | Specification |
|---|---|
| Power supply (depending on torque) | PoE Switch IEEE 802.3 802.3at Class 4 (2 N.m) 802.3bt Class 6 (4 N.m) 802.3bt Class 7 (6 N.m) |
| Wiring | With Ethernet cable Cat 5e mini 24 AWG |
| Operating temperature | 0°C (32°F) - 60°C (140°F) |
| Operating time | Time ON: 1 min 20 s Time OFF: 1 min 20 s |
| Index protection rating | IP30 (For indoor use only) |
| Safety level | Class III |
| Adjustable speed | 10-28 rpm |
| Roller speed (by default) | 25 rpm |
[NOTICE] For additional information on technical data, contact your Somfy representative.
Please separate batteries and cells from other waste and recycle them via your local collection facility.
We care about our environment. Do not dispose of the appliance with household waste. Take it to an approved collection point for recycling.
Certifications & Patents: UL Listed Shade Operator (E60495). US Patents US8253288, US8469171, US8597157, US9747787, patent pending.
Somfy.com
