Ryobi FVD50 USB Lithium Screwdriver Operator's Manual

General Power Tool Safety Warnings

WARNING: Read all safety warnings, instructions, illustrations, and specifications provided with this power tool. Failure to follow all instructions may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference.

Work Area Safety

• Keep work area clean and well lit.
• Do not operate power tools in explosive atmospheres.
• Keep children and bystanders away.

Electrical Safety

• Ensure power tool plugs match the outlet.
• Avoid body contact with earthed or grounded surfaces.
• Do not expose power tools to rain or wet conditions.
• Do not abuse the cord.
• Use extension cords suitable for outdoor use when operating outdoors.
• Use a ground fault circuit interrupter (GFCI) protected supply in damp locations.
• Use only the FVB01 battery pack and UL listed USB sources.

Personal Safety

• Stay alert and use common sense. Do not use power tools when tired or under the influence of drugs, alcohol, or medication.
• Use personal protective equipment, including eye protection.
• Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source or battery pack.
• Remove any adjusting key or wrench before turning the power tool on.
• Do not overreach; maintain proper footing and balance.
• Dress properly; avoid loose clothing, jewelry, and keep hair away from moving parts.
• Ensure dust extraction and collection facilities are connected and properly used if provided.
• Do not let familiarity lead to complacency; always be vigilant.
• Do not wear loose clothing or jewelry. Contain long hair.
• Do not use on a ladder or unstable support.

Power Tool Use and Care

• Do not force the power tool; use the correct tool for the application.
• Do not use the power tool if the switch does not turn it on and off.
• Disconnect the plug or remove the battery pack before making adjustments or changing accessories.
• Store idle power tools out of reach of children.
• Maintain power tools and accessories; check for misalignment, broken parts, or any other condition that may affect operation. Have damaged tools repaired before use.
• Keep cutting tools sharp and clean.
• Use the power tool, accessories, and tool bits in accordance with instructions, considering working conditions.
• Keep handles and grasping surfaces dry, clean, and free from oil and grease.

Battery Tool Use and Care

• Recharge only with the specified charger.
• Use power tools only with specifically designated battery packs.
• Keep battery packs away from metal objects when not in use.
• Avoid contact with battery liquid if ejected; flush with water if contact occurs.
• Do not use damaged or modified battery packs or tools.
• Do not expose battery packs or tools to fire or excessive temperature.
• Follow all charging instructions and do not charge outside the specified temperature range.

Service

• Have power tools serviced by a qualified repair person using only identical replacement parts.
• Never service damaged battery packs; only the manufacturer or authorized service providers should perform this.

Screwdriver Safety Warnings

• Hold power tool by insulated gripping surfaces when contacting hidden wiring.
• Know your power tool; read the operator's manual carefully.
• Always wear eye protection with side shields marked to comply with ANSI Z87.1.
• Protect your lungs; wear a face or dust mask if the operation is dusty.
• Protect your hearing; wear hearing protection during extended periods of operation.
• Battery tools are always in operating condition; be aware of possible hazards when not in use or changing accessories.
• Do not place battery tools or batteries near fire or heat.
• Do not crush, drop, or damage battery pack. Dispose of damaged batteries immediately.
• Batteries can explode in the presence of an ignition source. Never use cordless products in the presence of open flame.
• If liquid comes in contact with skin, wash immediately with soap and water. If liquid gets into eyes, flush with clean water for at least 10 minutes and seek medical attention.
• Save these instructions for future reference and to instruct others.

Symbols

The following signal words and meanings explain the levels of risk associated with this product:

Some of the following symbols may be used on this product. Please study them and learn their meaning.

Features

PRODUCT SPECIFICATIONS

• No Load Speed: 200/min. (RPM)
• Collet: 1/4 in.

Assembly

WARNING: Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged. Use of a product that is not properly and completely assembled or with damaged or missing parts could result in serious personal injury.

WARNING: Do not attempt to modify this product or create accessories or attachments not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

If any parts are damaged or missing, please call 1-800-525-2579 for assistance.

Operation

WARNING: Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury.

WARNING: Always wear eye protection with side shields marked to comply with ANSI Z87.1. Hearing protection may also be required depending on the type of attachment used and as prescribed elsewhere in this Operator's Manual. Failure to do so could result in objects being thrown into your eyes and other possible serious injuries.

WARNING: Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.

Applications

This product may be used for the purposes listed below:

• Driving screws with screwdriver bits
• Light-duty drilling

Installing/Removing Battery Pack

See Figure 1, page 9.

To install:

• Turn the battery cap counterclockwise to unlock and remove.
• Insert the battery pack into the product as shown.
• Align the grooves in the cap with the tabs on the end of the tool.
• Place the cap over the battery pack and push down.
• Turn the battery cap clockwise to lock in place.
• NOTE: Do not attempt to use this product if the battery cap is not securely closed.

To remove:

• Turn the battery cap counterclockwise to unlock and remove.
• Remove the battery pack from the tool.
• For complete charging instructions, see the operator's manuals for your battery pack and charger.

WARNING: Battery products are always in operating condition. Therefore, the switch should always be locked when not in use or carrying at your side.

LED Indicator Functions

See Figure 1, page 9.

When a charged battery pack is installed in the tool, the LED indicator will show the status of the battery when the tool is powered on.

High Temperature Protection

This tool is equipped with a high temperature protection feature that automatically deactivates the tool when it is overheated. To resume operation, allow the tool to cool and then turn the tool on.

In-line/Pivot Position

See Figures 2 - 3, page 9.

The screwdriver can be used in the in-line or pivot position. A pivot locking button is located on the top of the screwdriver.

To place the screwdriver in the in-line position: Hold in normal operating position, press pivot locking button down and twist front housing fully to the right.

To place the screwdriver in the pivot position: Hold in normal operating position, press pivot locking button down and twist front housing fully to the left.

Direction of Rotation

See Figure 4, page 10.

The direction of bit rotation is reversible and is controlled by a selector located on the rear of the handle. With the screwdriver held in the in-line position, the direction of rotation selector should be positioned fully forward for forward motion and fully back for reverse. With the screwdriver held in the pivot position, the direction of rotation selector should be positioned fully up for forward motion and fully down for reverse.

Setting the direction of rotation selector in the center (locked) position helps reduce the possibility of accidental starting when not in use.

NOTE: The screwdriver will not run unless the direction of rotation selector is pushed fully up/forward or down/back.

NOTICE: To prevent gear damage, always allow the collet to come to a complete stop before changing the direction of rotation.

To Load/Release Bits

See Figure 5, page 10.

Insert the bit into the collet and push the bit in as far as possible. To remove a bit, pull the bit straight out of the collet.

LED Lights

See Figure 6, page 10.

The LED lights, located on the front of the tool, illuminate during operation.

Driving Screws

See Figure 7 - 8, page 10.

• Place the screwdriver in the in-line or pivot position.
• Hold the tool firmly and place the bit at the point where the screw is to be driven.

WARNING: Do not drive a screw where there is likely to be hidden wiring behind the surface. Contact with a “live” wire will make exposed metal parts of the tool “live” and possibly shock the operator. If you must drive a screw where hidden wire may be present, always hold tool by insulated gripping surfaces (handle) when performing the operation to prevent a shock to the operator.

• Press the forward or reverse button to start the tool.
• Apply only enough pressure to keep driving the screw. Do not force the tool. Let the tool do the work.

Maintenance

WARNING: When servicing, use only identical replacement parts. Use of any other part could create a hazard or cause product damage.

General Maintenance

• Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents.
• Use clean cloths to remove dirt, dust, oil, grease, etc.

Product Identification

For service, replacement parts, or customer support, visit www.ryobitools.com or call 1-800-525-2579.

Model Number: FVD50

Please obtain your model and serial number from the product data plate.

This product is covered under a 2-year limited warranty. Proof of purchase is required.

RYOBI is a registered trademark of Ryobi Limited.