Light My Bricks LEGO Star Wars X-Wing Starfighter 75355 Light Kit Installation Guide

Package Contents

Before you begin, please verify that all components are present:

Individual Bags

• 1 x Bit Light 15cm - Cool White
• 1 x Large Bit Light 15cm - Cool White
• 4 x Bit Light 30cm - Pink
• 4 x Bit Light 30cm - Red
• 1 x Bit Light 15cm - Red to Blue
• 1 x Lightsaber - Blue

Mixed Components 1

• 4 x 2-Port Expansion Board
• 3 x 6-Port Expansion Board
• 1 x Gun Effects Board
• 1 x Pulse Effects Board
• 2 x 3m Squares

Connecting Cables

• 1 x 5cm Connecting Cable
• 2 x 15cm Connecting Cable
• 5 x 30cm Connecting Cable

Mixed Components 2

• 1 x Slope 30 1x1 x 2/3 - Trans-Clear
• 2 x Plate, Round 1x1 with Open Stud - Black
• 4 x Plate, Round 1x1 - Trans-Clear
• 4 x Technic, Pin 1/2 without Friction Ridges - Light Bluish Gray
• 1 x Bracket 1x1 - 1x1 - Light Bluish Gray
• 1 x Plate, Modified 1x2 with Bar Handle on End - Black
• 1 x Plate, Modified 1x2 with 1 Stud with Groove and Bottom Stud Holder (Jumper) - Black
• 1 x Tile, Modified 1x1 with Open O Clip - Black

USB Power Cable

• 1 x USB Power Cable (Power Source not included)

Before You Begin

Laying Cables

Cables can be routed between and underneath LEGO bricks, plates, and tiles. Ensure cables are laid correctly between the LEGO studs. Do not force LEGO pieces together around cables; ensure they lie comfortably within each stud. ⚠️ CAUTION: Forcing LEGO pieces over a cable can damage the cable and light.

Connecting Cable Connectors to Expansion Boards

Exercise care when inserting connectors into Expansion Board ports. Connectors only fit one way. With the expansion board facing up, locate the soldered "=" symbol on the left side of the port. The connector side with exposed wires should face the "=" symbol when inserting. Do not force a plug if it doesn't fit easily. Incorrect insertion can bend pins or overheat the board.

Connecting Cable Connectors to Strip Lights

Take care when inserting connectors into Strip Light ports. Connectors only fit one way. With the Strip Light facing up, ensure the side of the connector with exposed wires faces down. Do not force a plug if it doesn't fit easily, as this will damage the plug and connector.

Connecting Micro Cable Connectors to Micro Expansion Board Ports

Exercise care when inserting micro connectors into Micro Expansion Board ports. Connecting Micro Bit Lights to Micro Expansion Boards is similar to Strip Lights. With the expansion board facing up, ensure the connector side with exposed wires faces down. If a plug doesn't fit easily, do not force it. Use a fingernail to push the plastic part of the connector into the micro port.

Installing Bit Lights Under LEGO Bricks and Plates

When installing Bit Lights under LEGO pieces, ensure they are placed correctly with the yellow LED component exposed. They can be placed directly on top of LEGO studs or in between them.

Symbols Used in This Guide

• Connect: ▶️ Used when connecting a LEGO piece or LMB component.
• Disconnect: ◀️ Used when removing a LEGO piece/section or LMB component.
• Directional: ➡️ Used to show cable routing, component placement, or movement.
• Bend/Pivot: ↪️ Used when a component needs bending or pivoting.
• Turn/Flip: ? Found in the top left corner when the set needs rotation or flipping.
• Twist/Braid: 〰️ Seen when cables need grouping and twisting.
• Power On Test: ☀️ Found at the end of a major step to test lights.
• Note: ? Notes accompany instruction photos to explain actions.

Additional Symbols & Notes

• Repeat Step: x2 Indicates repeating a previous step.
• Connect Focus: Highlights an area where a component is being connected.
• Disconnect Focus: Highlights an area where a component is being disconnected.
• General Focus: Highlights an area where an action is needed.
• General Note: ? Explains difficult sections or confusing photos.
• Connect Note: ? Used when focusing on connecting a component (e.g., Power Bank).
• Disconnect Note: ? Used when focusing on disconnecting a component or showing removed pieces.

Example Note: Take the 5cm Connecting Cable from the 4-Port Micro Expansion Board and route it into the "IN" port of the Flicker Effects Board.

Example Note: Connect to a 5V USB Power Bank, 5V USB Wall Adaptor, or USB to AA Battery Pack (sold separately).

Example Note: You should have these parts left over that were removed from the LEGO set.

Blueprint

The blueprint provides an overview of the light kit's wiring, showing connections between lights, expansion boards, and the power source. It illustrates the overall circuit layout for the LEGO Star Wars X-Wing Starfighter 75355.

Instructions

To ensure a smooth installation, please read and follow each step carefully. Refer to the online troubleshooting guide for any issues.

Step 1

Connect the Lightsaber - Blue to the 6-Port Expansion Board.

Step 2

Prepare components: Plate, Round 1x1 with Open Stud - Black; Cool White 15cm Large Bit Light; Plate, Modified 1x2 with Bar Handle on End - Black; Tile, Modified 1x1 with Open O Clip - Black; Plate, Modified 1x2 with 1 Stud with Groove and Bottom Stud Holder (Jumper) - Black.

Step 3

Connect the USB Power Cable. ? Note: Connect to a 5V USB Power Bank, 5V USB Wall Adaptor, or USB to AA Battery Pack (sold separately).

Troubleshooting Note: If lights are not working, try a different port on the expansion board to identify the fault. Consult the troubleshooting section for expansion board issues.

Step 4

Begin assembly of the X-Wing Starfighter model, incorporating lights as shown in the diagrams. This step involves placing components and routing cables within the model's structure.

Step 5

Prepare and install components: Cool White 15cm Bit Light, Bracket 1x1 - 1x1 - Light Bluish Gray, Slope 30 1x1 x 2/3 - Trans-Clear.

Step 6

Install the Red to Blue 15cm Bit Light and Plate, Round 1x1 with Open Stud - Black.

Step 7

Connect the 15cm Connecting Cable to the 6-Port Expansion Board.

Step 8

Disconnect the 15cm Connecting Cable from the 6-Port Expansion Board. Prepare Red 30cm Bit Light and Technic, Pin 1/2 without Friction Ridges - Light Bluish Gray.

Step 9

Thread components and prepare the 2-Port Expansion Board. Repeat the threading process for the other 6 pieces.

Step 10

Install the 30cm Connecting Cable and continue assembly of the X-Wing model, routing cables as indicated.

Step 11

Install Technic, Pin 1/2 without Friction Ridges - Light Bluish Gray and Red 30cm Bit Light.

Step 12

Repeat the threading process for the remaining 6 pieces. Prepare the 2-Port Expansion Board.

Step 13

Install the 30cm Connecting Cable and continue assembly of the X-Wing model, routing cables as indicated.

Step 14

Repeat steps 8-13 on the other side of the model. Thread the four 30cm Connecting Cables to the bottom of the model. Connect the four 30cm Connecting Cables from the S-Foils to the 'OUT' ports of the Gun Effects Board. Connect the 15cm Connecting Cable to the '5V' port of the Gun Effects Board.

Step 15

Install the Pink 30cm Bit Light and Plate, Round 1x1 - Trans-Clear.

Step 16

Continue assembly of the X-Wing model, integrating lights and components as shown.

Step 17

Continue assembly of the X-Wing model, integrating lights and components as shown.

Step 18

Install the Pulse Effects Board. Connect the other end of the 30cm Connecting Cable to an 'OUT' port of the Pulse Effects Board. Connect the 5cm Connecting Cable to the '5V' port on the Pulse Effects Board and the other end to the 6-Port Expansion Board from step 7.

Step 19

Reconnect the 15cm Connecting Cable to the 6-Port Expansion Board from step 2.

Step 20

Use the 2x Adhesive Squares to attach the 6-Port Expansion Board to the back of the plaque on the base.

Final Product

This completes the installation of the Light My Bricks LEGO Star Wars X-Wing Starfighter 75355 Light Kit. The X-Wing Starfighter is now illuminated.

Images show the completed model with various lights activated, including cockpit lights, engine lights, and laser cannons.

Troubleshooting

Light My Bricks components are small and can be easily damaged if not handled correctly. Always read the "Important things to note" section of the User Guide carefully and follow handling procedures to prevent faults.

If you experience issues with your light kit, watch the troubleshooting video or consult the list of common causes below.

Check Power and Batteries

Ensure batteries have power using a battery charge gauge. If no power, replace batteries. If batteries have power, check correct insertion into the battery pack. Inside the battery pack, symbols indicate correct AA battery orientation; the flat side should align with the spring side.

Check Your Wires

Light My Bricks components are small and delicate. Be careful when unpacking and avoid pulling wires forcibly, as this can damage the LED soldering. If wiring is detached from the LED, the light will not operate. Check for pinched wires between LEGO bricks and plates. Pinched wires with exposed conductors touching can cause crosswires and prevent lights from functioning.

Check Expansion Board Ports / Strip Light Ports / Effects Board Ports

Connectors must be inserted into expansion board, strip light, or effects board ports in the correct direction. Forcing connectors incorrectly can damage the pins. Damaged ports may prevent lights from working, and if pins touch, it can cause a short circuit, affecting all lights. A short circuit can also lead to overheating. If a short circuit is suspected, disconnect power immediately. Batteries can fail, catch fire, or explode if left connected to a short circuit. If a component seems faulty due to bent pins, inspect ports carefully; each port has 2 small pins that should be straight. Bent pins indicate a faulty port.

Contact Us

For enquiries regarding the online shop, products, or general questions, please refer to the Frequently Asked Questions webpage. Alternatively, contact Customer Services by visiting the online support portal at support.lightmybrick.com.

Thank you for purchasing this product. We hope you enjoy it!