Light My Bricks LEGO Stormtrooper Helmet #75276 Light Kit Installation Guide

Introduction

We're here to help you get started on the LEGO® Stormtrooper Helmet (75276) Light Kit. This guide details the instructions for the LED light kit only. If you run into any issues, please refer to the troubleshooting section towards the end of this guide. Have fun and enjoy!

Package Contents

• 6 x Cool White 30cm Bit Lights
• 2 x Large Cool White 30cm Bit Lights
• 1 x 12-Port Expansion Boards
• 1 x USB Power Cable (Power Source not included)

LEGO Pieces Included

• 2 x Black Plate 1x6
• 2 x Black Round Plate 1x1 w Open Stud
• 2 x Black Arm Skeleton, Bent w Clips (Horizontal Grips)
• 4 x Black Plate 1x1 Modified Rounded w Handle

Before You Begin

Laying Cables

Cables can fit between and underneath LEGO® bricks, plates, and tiles if laid correctly between the LEGO® studs. Do NOT forcefully join LEGO® together around cables; instead, ensure they are laying comfortably between each stud. CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light.

Diagram shows LEGO bricks with wires correctly placed underneath and a warning symbol for forcing bricks.

Connecting Cable Connectors to Expansion Boards

Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered "=" symbol on the left side of the port. The connector side with the wires exposed should be facing toward the soldered "=" symbol as you insert into the port. If a plug won't fit easily into a port connector, do not force it. Incorrectly inserting the connector can result in bent pins inside the port or possible overheating of the expansion board when connected.

Diagram shows expansion board ports with correct (✔️) and incorrect (❌) connector insertion, highlighting the "=" symbol.

Connecting Cable Connectors to Strip Lights

Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won't fit easily into a port connector, don't force it. Doing so will damage the plug and the connector.

Diagram shows strip light ports with correct (✔️) and incorrect (❌) connector insertion, indicating wire orientation.

Connecting Micro Cable Connectors to Micro Expansion Board Ports

Take extra care when inserting the micro connectors to micro ports of Micro Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is similar to connecting lights and cables to Strip Lights. With the expansion board facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won't fit easily into a port connector, do not force it. Use your fingernail to push the plastic part of the connector to the micro port.

Diagram shows micro expansion board ports with correct (✔️) and incorrect (❌) connector insertion, indicating wire orientation.

Installing Bit Lights Under LEGO® Bricks and Plates

When installing Bit Lights under LEGO® pieces, ensure they are placed the correct way up (Yellow LED component exposed). You can either place them directly on top of LEGO® studs or in between.

Diagram shows a LEGO plate with a bit light installed underneath, and examples of bit lights with wires.

Instructions

To ensure a smooth installation of your light kit, please read and follow each step carefully. If you run into any issues, please refer to the online troubleshooting guide.

Legend

• ➡️ DISCONNECT
• ? CONNECT / RECONNECT
• ? TURN / FLIP
• ➡️ DIRECTIONAL
• ? TWIST / BRAID
• ⚡ POWER ON / TEST
• ? NOTE ICON

Step 1

Begin assembly of the Stormtrooper helmet. Images show initial steps of connecting LEGO bricks and preparing components.

Visuals depict assembling the helmet's base and lower face structure, routing wires.

Step 2

Install the first set of Bit Lights. Images show attaching lights to specific LEGO pieces and preparing them for installation.

Visuals show attaching a Cool White 30cm Bit Light to a white circular LEGO piece and a small black connector.

Step 3

Continue assembling the helmet and integrating the lights. Images show attaching lights to internal helmet components.

Visuals show attaching two Cool White 30cm Bit Lights to white LEGO pieces and then integrating these into the helmet's internal structure.

Step 4

Further assembly and wire routing. Images show connecting more LEGO pieces and carefully guiding wires through the structure.

Visuals show connecting black LEGO plates and routing wires, including two Cool White 30cm Bit Lights.

Step 5

Connect the 12-Port Expansion Board and route wires. Images show placing the expansion board and arranging the cables.

Visuals show the Stormtrooper helmet from the front and back, with the 12-Port Expansion Board being positioned and wires being managed.

Step 6

Connect the USB Power Cable. Images show the USB cable and its connection point.

Visuals show the USB Power Cable and a note indicating connection to a USB power source (sold separately).

Step 7

Install a Large Cool White 30cm Bit Light and a specific LEGO piece. Images show the components and their assembly.

Visuals show a Large Cool White 30cm Bit Light, a connector, and a black route plate with an open stud.

Step 8

Final wire routing and integration. Images show threading wires through holes and securing the expansion board.

Visuals show threading wires through LEGO pieces, connecting the expansion board, and placing it within the helmet structure. Includes details on black arm skeleton pieces and black 1x6 plates.

Final Product

This completes the installation of the Light My Bricks Stormtrooper Helmet 75276 Light Kit. Enjoy your illuminated LEGO model!

Images show the fully assembled and illuminated LEGO Stormtrooper Helmet.

Troubleshooting

Light My Bricks lighting kits contain small, delicate components that can be easily damaged if not handled correctly. To prevent unnecessary damage, carefully read the "Important things to note" section in the User Guide and follow the handling procedures. If you experience issues, watch our troubleshooting video or read on for common causes.

Check Your Batteries

Flat Battery Pack (CR2032)

Ensure batteries have power using a charge gauge. If no power, replace them. If still no power, check correct insertion. Inside the battery pack, a symbol indicates CR2032 insertion. On the "+" side of the pack, the battery's "+" symbol should face downwards. On the "-" side, the battery's "+" symbol should face upwards.

Diagram shows a flat battery pack with CR2032 batteries and arrows indicating correct polarity (+ symbol facing down on one side, up on the other).

Round Battery Pack (CR2032)

For stacked battery packs, ensure BOTH CR2032 batteries have the "+" symbol facing upwards.

Diagram shows a round battery pack with CR2032 batteries and arrows indicating correct polarity (+ symbol facing upwards for both batteries).

AA Battery Pack

Inside the battery pack, symbols indicate AA battery direction. The flat side of the battery should pair with the spring side of the battery pack. If the kit still isn't operating correctly after correct battery installation, check the wiring.

Diagram shows an AA battery pack with symbols indicating correct battery insertion (flat side to spring).

Check Your Wires

Light My Bricks components are small and can be damaged if not handled correctly. Be careful when unpacking and avoid pulling wires, as this can damage the soldering. If wiring is detached from the LED, the light will not operate. Check for pinched wires underneath or between bricks; pinched wires can cause a crosswire and prevent lights from functioning.

Diagrams show detached LED wires and wires pinched between LEGO bricks.

Check Your Expansion Board Ports / Strip Light Ports / Effects Board Ports

Connectors can only be inserted into expansion board, strip light, or effects board ports in one direction. Forcibly inserting connectors incorrectly will damage the pins. A damaged port may not work, and if pins are bent and touching, it can cause a short circuit, stopping all lights. Short circuits can also cause overheating. If a short circuit is suspected, DISCONNECT POWER IMMEDIATELY. Batteries can fail, catch fire, or explode if left connected to a short circuit. To identify a faulty port, look for bent pins inside each port.

Diagrams show expansion board ports with correct (✔️) and incorrect (❌) pin alignment, highlighting bent pins.

Contact Us

If you have an enquiry regarding the online shop, our products, or a general enquiry, please refer to our Frequently Asked Questions webpage. Alternatively, you can contact our Customer Services team by visiting our online support portal: support.lightmybricks.com

We thank you for purchasing this product and hope you enjoy!