VEVOR

Introduction

This is the original instruction manual. Please read all manual instructions carefully before operating. VEVOR reserves the right to interpret its user manual. The appearance of the product shall be subject to the product you received. VEVOR will not provide notification for any technology or software updates on its product.

Assembly Instructions

NOTE: Excessive force or effort is never necessary to change the seating position of the chair. Do not operate the recliner by applying force or pressure to the legrest.

Figure 1: Diagram showing a recliner chair with labels pointing to: Articulating Headrest, Gas Spring Actuating Lever ⚙️, Padded Push Handle, Upholstered Arm Support, Frame, Upholster Back, Upholster Seat, Upholstered Legrest Skirt, and Upholstered Footrests.

Figure 2: Diagram showing the underside of the recliner with labels for: Clevis Pin, Bridge Clip, Bolt & Nut, and Back Brace with "U" Brackets.

Note: After removing all components from the carton, engage the two casterlocks before beginning assembly.

Figure 2 shows the location of two clevis pins, two ring cotter clips, one bolt, and one nut. Remove all above hardware from the back brace.

Figure 3: Assembly Steps

• Step 1: Undo the Clevis Pins on the Upholster Back, on both sides, so mounting holes are exposed. Press the buckles to remove the side plates (both sides).
• Step 2: Align the holes on the upright back tubes of the upholstered back with the holes on the seat frame. Replace the clevis pins through the mounting holes. Secure the two clevis pins by replacing the bridge clips.
• Step 3: Remove cardboard shipping retainers from around the Gas Spring Cylinder. The holes at both ends of the gas spring should align with the holes in the seat frame cross brace and the holes in the upholster back.
• Step 4: Align holes in the arm support mount to the mounting holes in the seat frame. Secure with a screw and nut. Repeat for the other side.

Instructions for Use

Slide Tables

To place either table in raised position: Raise the table all the way up and slide it in until tabs engage slots in the mount bracket. Press down lightly on the table to ensure lock tabs are engaged.

To return table to self-storing position: Lift the table up until tabs disengage slots. Slide out and allow the table to lower. See Figure 4.

Figure 4: Diagram illustrating the slide table mechanism. It shows the Table Mount Bracket, Clevis Pin Attachment, and Armrest. Arrows indicate the table in 'Disengaged Position', 'Stored Position', and 'Engaged Position', with text noting that 'Tabs engage into slots on table mount bracket'.

Articulating Headrest

The articulating headrest may be adjusted to a comfortable position by pulling forward or pushing back.

Seat Positioning

Upright: Initial position. From any position, grasp the gas spring actuating lever ⚙️, slowly guide the back up fully, and release the lever. Return the patient to the desired position by pushing upward on the padded push handle.

Deep recline: From the initial position, grasp the gas spring actuating lever ⚙️ with one hand and push back on the padded push handle.

Elevated leg rest: From the initial position, do not grasp the gas spring actuating lever ⚙️; push back on the padded push handle.

Trendelenburg position: From any position, grasp the gas spring actuating lever ⚙️ with one hand while actuating the lever with the other. Slowly guide the back down fully and release the lever.

Other: The articulating headrest may be adjusted to the desired position by pulling forward or pushing back.

Figure 5: A grid of images showing the recliner in different positions: 'upright', 'deep recline', 'elevated leg rest', and 'trendelenburg position'. A separate image shows the back of the recliner with an arrow pointing to the 'Gas Spring Actuating Lever' ⚙️.

Caster Operation

To lock casters:

To prevent the rear casters from turning, step on the rear pedal of the caster until the pedal engages. (The front of the pedal will protrude from the wheel cover).

To unlock casters:

Step on the protruding front part of the pedal to disengage the lock and unlatch.

Figure 6: Caster Lock/Unlock

• To Lock: Pedal protrudes, push down. ✔️ [Lock]
• To Unlock: Push down. ❌ [Unlock]

CAUTION: Do not operate the recliner by applying force or pressure to the legrest. Avoid placing hands or legs in creases near the recliner mechanism. Casters must be locked except during transport.

Maintenance & Cleaning

Every Three Months

• Check and clean casters.
• Tighten nuts.
• Check brakes on casters.
• Check and clean lock recline mechanism ⚙️.

For upholstery maintenance and stain removal, the following hints will be helpful:

• Ordinary dirt: Wash with warm water and a mild soap or detergent.
• Stubborn dirt: Using a soft bristle brush, follow directions above.
• Ground-in dirt: Scrub with powdered cleanser or similar detergent.
• Chewing gum: Scrape carefully.
• Nail polish and remover: Blot immediately to prevent damage.
• Ball point pen: Blot immediately with a white cloth dampened in watch or mineral oil.
• Waxing and refinishing: Improve wearability. Use any quality paste wax.

A diluted solution of 10% (or less) of bleach or Clorox may be used when cleaning this chair.

Manufacturer and Importer Information

Manufacturer: Jiangyin Huashi Medical Equipment Co., Ltd

Address: No. 589 Hualu Road, Jiangyin City, Wuxi City, Jiangsu Province, 214400, China

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREET, EASTWOOD NSW 2122, Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX

EC Representative: E-CrossStu GmbH. Mainzer Landstr.69, 60329 Frankfurt am Main.

Technical Support and E-Warranty

For technical support and e-warranty information, please visit: www.vevor.com/support