Scope of Delivery
The package includes:
- DIN rail power supply (slim)
- An additional sheet with a link to the user manual
Technical Specifications
| Model | 1010425 | 1010426 | 1010427 | 1010428 | 1010429 | 1010430 |
|---|---|---|---|---|---|---|
| Input | 100 - 240V AC, 50/60 Hz | |||||
| Output | 5V 2A 10W | 12V 1,25A 15W | 12V 2,5A 30W | 24V 2,5A 60W | 12V 4,5A 54W | 12V 7,5A 90W |
| Adjustable Output Voltage | 4V - 6V | 11V - 13V | 11,4V - 12,6V | 22,8V - 25,2V | 11,4V - 12,6V | 11V - 13V |
| Relative Humidity | Operating: 20 - 90% (non-condensing) Storage: 10 - 95% |
|||||
| Temperature | Operating: -20 to +50°C Storage: -40 to +80°C |
|||||
| Appliance Class | II | |||||
| IP Code | IP 20 | |||||
| Primary Cable | 12 AWG - 18 AWG (3.3mm² - 0.8mm²) | |||||
| Secondary Cable | Heat-resistant up to min. 80 °C (e.g. UL1007) | |||||
| Dimensions (mm) | 18 x 90 x 58 | 18 x 90 x 58 | 78 x 92 x 61 | 52.5 x 90 x 58 | 52.5 x 90 x 58 | 70 x 90 x 58 |
| Weight (g) | 72 | 74 | 234 | 188 | 186 | 246 |
| For installation on | DIN rail of type TS 35/7.5 or TS 35/15 (or similar) | |||||
Safety Instructions
⚠️ WARNING: Danger to life! All installation and assembly work must be carried out exclusively by experienced specialists trained and experienced in the installation, commissioning, and maintenance of DIN rail power supplies in conjunction with electromechanical components. All work on the 230 V AC mains must only be performed by qualified electricians.
⚠️ WARNING: Electric shock hazard! Incorrect modifications to the Poppstar DIN rail power supply may result in 230 V AC voltage being applied to other components.
⚠️ WARNING: Short circuit hazard! Never insert objects into ventilation slots or connection sockets.
⚠️ WARNING: Fire hazard! Selecting a higher operating voltage than specified by the manufacturer can cause serious damage to the DIN rail power supply and the connected electronics!
For all work on the 230 V AC mains, current VDE regulations and corresponding country-specific regulations must be observed.
Incorrect wiring of the DIN rail power supply can lead to destruction of the electronics.
- Keep the product out of reach of children.
- Contains small parts that can be swallowed – keep away from small children!
- Never open the housing.
- Never cover the product.
- Never expose the product to extreme conditions such as heat/cold, wet/humid environments, foreign objects (e.g., shavings or liquids), direct sunlight, vibrations, shocks, or mechanical pressure.
- Do not modify or dismantle the product or accessories.
- Never repair defective products yourself – please contact our technical support.
- Use the product only in dry indoor areas.
Installation
ATTENTION: Allowed mounting position: To ensure proper ventilation during operation, only vertical wall mounting is allowed for the DIN rail power supply. Horizontal mounting is not allowed.
- Mounting location: Keep the ventilation slots of the DIN rail power supply free at the top and bottom (20-40mm). Sufficient space around the power supply at the mounting location (5-10mm) must be provided for cooling.
- Tilt the power supply slightly backwards and place it on the rail from above.
- Push the power supply down as far as it will go.
- To lock the power supply in its place, press against the lower front until it clicks into the rail (makes a click sound).
- Gently shake the power supply to check that it is securely attached.
Wiring
WARNING: Danger to life! The connection must be made in a voltage-free/load-free state!
WARNING: Use separate wires for the inputs and outputs.
WARNING: The DIN rail power supply works as soon as the primary side is receiving voltage. It does not have its own on/off switch.
We recommend checking the output voltage once with a multimeter before connecting a device, because an unwanted output voltage could damage or destroy your device.
- Open all screw terminals (+, -, L, N) with a flathead or crosshead screwdriver.
- Route the cables in the cable holders and fasten the screw terminals again, so the cables are firmly secured.
- Check that the cables are firmly secured.
Adjusting the Output Voltage
Above the symbol "+V ADJ" on the power supply, you will find the potentiometer for adjusting the output voltage (values see table). The output voltage can be increased by turning it clockwise ? with a flathead or crosshead screwdriver.
Disassembly
WARNING: Before removing, switch off the main power supply, check that there is no voltage present, and disconnect the power supply from the mains.
- Put a flathead screwdriver into the groove of the release slide (at the bottom of the power supply) and pull it downwards.
- Lift the lower front edge of the power supply carefully and remove it.
Malfunction / Troubleshooting
WARNING: A functional test may only be carried out by qualified electricians.
Should a malfunction occur, check the following:
- Is the LED ("Output voltage OK") lit? (except model 1010427) ✔️
- Are the cables for the nominal input voltage (L, N) connected?
- Is the protective earth (PE) connected?
- Is the shielding/ground of the power supply cable connected to the device?
- Is the device connected to the output with the correct polarity?
- Has the correct cable diameter been selected?
- Is the nominal output voltage (5V/12V/24V, see table) correctly applied to the input of the device?
- Has the maximum output current been exceeded by too many devices?
Storage and Maintenance
Store the product in a cool and dry place.
Use a dry and soft cloth for cleaning the product – do not expose it to cleaning agents or chemicals!
Liability
Poppstar GmbH is not liable for personal injury or property damage caused by incorrect installation, use, or maintenance.
Instructions for Disposal
Product:
?️ [WEEE symbol] Electrical and electronic equipment must not be disposed of with regular household waste according to the European WEEE Directive. Their components must be recycled or disposed of separately because toxic and hazardous components can cause permanent damage to health and the environment if disposed of incorrectly.
As a consumer, you are obliged under the Electrical and Electronic Equipment Act (ElektroG) to return electrical and electronic equipment free of charge at the end of its service life to the manufacturer, the outlet, or public collection points set up for this purpose. Details are regulated by applicable national law. The symbol on the product, instructions for use, and/or packaging indicates these regulations. By separating, recycling, and disposing of old appliances in this way, you are making an important contribution to protecting our environment.
Packaging:
♻️ [Recycling symbol] Packaging can be disposed of free of charge at the appropriate collection points: paper in the paper bin, plastics in the plastic bin, and glass in the correct glass container.
EC Declaration of Conformity
By means of the CE symbol, Poppstar GmbH declares that the product complies with the basic requirements and directives of the European regulations.
Symbols Used on the Product
| Symbol Description | Symbol |
|---|---|
| Protective Insulation: Appliance Class II | ? [Appliance Class II / Protective Insulation] |
| For indoor use only | ? [Indoor use only] |
| Power supply type: Switching power supply | S [Switching power supply] |
| Short-circuit proof safety transformer (with fuse and thermal protection) | ? [Safety transformer with protection] |
| Limited Power Source | LPS [Limited Power Source] |
Contact Information
Poppstar GmbH
Heidelbergerstraße 49
74746 Höpfingen
Germany
E-Mail: info@poppstar.eu
Tel: +49 6283 21570-27 (Mon.- Fri. 14:00 - 17:00)
Live Chat: www.poppstar.eu (Mon.- Fri. 8:00 - 17:00)
Misprints and changes to the product, packaging, and product documentation reserved.
Poppstar - Ihr Onlineshop für Elektronik und Baumarktzubehör
