onn. 5.1.2 Atmos Soundbar User Manual

Safety Information

General Safety Guidelines

DO: Ensure all electrical connections are properly made and in accordance with manufacturer instructions. Switch off and withdraw the mains plug before making or changing connections. Consult your dealer if in doubt about the safety of the equipment. Be careful with glass panels. Do not place equipment where it can be walked on or where cords can be trod on or chafed.

DON'T: Obstruct ventilation openings. Do not place near heat sources. Do not expose to liquids. Do not place objects on the equipment. Do not use makeshift stands. Do not listen to headphones at high volume for extended periods to avoid hearing damage. Do not operate equipment if it is not designed for unattended operation. Switch off at the mains socket and unplug when not in use.

ABOVE ALL: Never let anyone, especially children, push anything into holes, slots, or openings in the equipment, as this could result in a fatal electric shock.

Battery Safety Guidelines

CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Replace only with the same or equivalent type. Do not expose batteries to extreme heat or fire. Do not dispose of batteries in fire or a hot oven, or mechanically crush or cut a battery, which may result in an explosion.

Product Overview

Front View

Features a POWER Indicator (orange when pairing succeeds), PAIR button (for subwoofer pairing), and AC 100-240V Power Socket.

Rear View of Subwoofer

Includes AC power socket and an On/Off Switch.

Top View

Features a Remote Control Sensor (receives signals from the remote control).

Bottom View

Contains ports: AUX IN PORT, OPTICAL PORT, LAN PORT, HDMI OUT (ARC) PORT, HDMI IN 3 PORT, HDMI IN 2 PORT, and USB IN PORT.

Remote Control

The remote control includes:

• Power: Switches the unit between ON and OFF modes.
• Mute: Mutes the sound.
• Previous/Next: Controls previous/next track in USB/BT/WiFi mode.
• Up/Down (VOL+/-): Increases/decreases volume.
• Play/Pause: Starts/pauses playback in USB/BT/WiFi mode.
• Bluetooth mode: Switches to Bluetooth mode and initiates pairing.
• SUB +/-: Increases/decreases bass level.
• Source: Cycles through input sources (ARC-HDMI, HDMI 1, HDMI 2, HDMI 3, BT, OPTICAL, USB, AUX).
• Sound mode: Selects sound modes (Standard, Movie, Music).
• HDMI mode: Selects HDMI input sources.
• Channel controls: Adjusts volume for Treble, FL&FR, Center, Top L&R, Side L&R channels.

Preparation and Connections

Installing Remote Control Batteries

Press and slide the battery compartment cover on the back of the remote. Insert two AAA batteries, observing correct polarity (+ and -). Close the cover.

Connecting to the Power Outlet Supply

Use the provided AC cord. Unwind it fully. Connect one end to the AC IN Socket at the bottom of the unit and the other to a power outlet. Ensure the AC cord is firmly inserted.

Subwoofer Connection

Connect the AC cord to the subwoofer. Turn on the unit. The orange light on the rear panel will flash, indicating pairing mode. When paired, the light becomes solid. The subwoofer automatically enters standby mode when the soundbar is off or in standby. If pairing fails, perform manual pairing by holding 'VOL-' and 'VOL+' on the soundbar for 3 seconds (display shows "CNCT" fast flashing), then hold the PAIR button on the subwoofer for 3 seconds (LED flashes fast). Pairing takes about 25 seconds.

Using the AUX Connection

Connect the TV's audio output to the soundbar's AUX IN port using a 3.5mm to RCA stereo audio cable (not included) or a 3.5mm to 3.5mm stereo audio cable (included) from the TV's headphone port.

Using the HDMI Connection

Connecting with a TV: For TVs supporting HDMI CEC and eARC, use an HDMI cable (included) to connect the TV's HDMI ARC/eARC port to the soundbar's HDMI OUT (ARC) port. This allows audio to be sent from the TV to the soundbar and enables control of the soundbar with the TV remote.

Connecting with a TV and other devices: Connect HDMI IN ports on the back of the unit to HDMI OUT ports on devices like Blu-ray players or game consoles. Connect the TV's HDMI ARC/eARC port to the soundbar's HDMI IN (ARC) port. Use the Source button or remote to select the desired HDMI input (HDMI 1, HDMI 2, HDMI 3, or ARC).

USB Playback

Connect a USB flash disk to the USB IN port on the soundbar to play music.

Using the LAN Connection

Connect the soundbar's LAN port to your home network using the included LAN cable for network connectivity.

Bluetooth Connection

1. When the unit powers on, press the Source button to change to Bluetooth mode ("BT READY" flashes for 10s). Long press the Bluetooth button (or Source button for 3s) to enter pairing mode.

2. On your device (phone, tablet), enable Bluetooth and search for devices. Select "onn. 5.1.2 Soundbar".

3. Once paired, the display shows "PAIRED". You can now play audio from your device.

AirPlay 2

Requires iOS 11.4 or later. Connect your iOS device to the same Wi-Fi network as the soundbar. Open a music app, tap the AirPlay icon, and select "onn. 5.1.2 Soundbar". You can control playback (play/pause, volume) from your device.

Setup in Apple Home app: Connect your iOS device to Wi-Fi. Open the Apple Home app, tap '+', select 'Add Accessory'. Search for the device. When found, click the device name. Follow prompts to add the accessory to your network. Once connected, it will appear in 'My Home'.

Operation

Selecting the Sound Mode

Press the Sound mode button repeatedly on the remote or unit to cycle through pre-programmed sound modes: Standard (STD), Movie (MOVE), and Music (MUSIC). Note: Non-Dolby Audio sources may not support all sound modes.

Adjusting the Volume

MASTER VOLUME: Press VOL+/- on the unit or remote to adjust the main volume (range 1-39). Press MUTE on the remote to silence audio; press again to resume.

SUB VOLUME: Short press SUB+/- on the remote to adjust the subwoofer bass level (range -9 to 9).

Channel Volume Adjustment: Press the channel control buttons (e.g., Treble, FL&FR) on the remote to select a channel, then press VOL+/- to adjust its sound level (ranges vary per channel).

General Operation

1. Power On: Press the Power button. The unit enters ON mode. The LED screen displays "WELCOME" and then turns off after 10 seconds of inactivity, entering a dormant state. A red indicator light slowly flashes for Wi-Fi startup (up to 15 minutes) if the network isn't set up, then turns off. If the network was previously set up, the indicator turns off once connected.

2. Power Off: Press the Power button again. The screen displays "GOODBYE" and turns off. The system enters standby mode, indicated by a lit red LED.

3. Auto Standby: The soundbar enters standby mode automatically after 10 minutes of no input, no operation, or silence.

4. Complete Power Off: Disconnect the mains plug from the power outlet for complete power off.

Factory Default Resetting

To reset the unit to factory defaults, hold VOL- and VOL+ on the soundbar simultaneously for 5 seconds. The display will show "RESET".

Placement and Mounting

Placement

Position the soundbar and subwoofer as shown in diagrams (visual descriptions needed here). Ensure adequate ventilation.

Wall Mounting

1. Drill 4 parallel holes in the wall, spaced 20mm apart vertically, according to wall type and bracket dimensions. (Diagram description: Holes drilled into a wall).

2. Insert wall anchors (not included) into the holes if necessary.

3. Insert screws (e.g., 4x35mm for drywall, not included) into the anchors/holes.

4. Attach the wall brackets (included) to the wall using the screws.

5. Mount the soundbar onto the brackets. Caution: Ensure the front panel does not face the wall during installation.

Maintenance and Tips

Cleaning the Unit

Ensure the unit is unplugged. Wipe the case with a slightly moist, lint-free cloth. Do not use alcohol, ammonia, or abrasive cleaners.

Software Update

When connected to the internet, the system automatically checks for software updates. If an update is needed, the product will update automatically. The bar will display "UPDATING" on the front display during this process.

Hints and Tips

If a problem occurs, check the following table for potential solutions. Many issues are minor and can be resolved easily.

Adjusting Volume Levels

MASTER VOLUME: Use VOL+/- on the unit or remote (Range: Min 1 to Max 39).

SUB VOLUME: Use SUB+/- on the remote (Range: Min -9 to Max 9).

Channel Volume: Press channel buttons (Treble, FL&FR, Center, etc.) and use VOL+/- to adjust levels (e.g., Treble: Min -9 to Max 9; FL&FR, Center, Top L&R, Side L&R: Min -5 to Max 5).

Specifications

• Weight: 7.4kg
• Specifications are subject to change without prior notice.

Warranty Information

Walmart, Inc. Limited Warranty

This warranty is the only warranty applicable to this product. No employee or representative of Walmart shall create any guarantee or modify this warranty. Repair or replacement is the exclusive remedy. Walmart is not liable for consequential damages. This warranty is governed by the laws of the State of Arkansas. This warranty grants specific legal rights, and you may also have other rights which vary by state.

Limitations: This warranty does not apply to damage caused by accident, misuse, abuse, neglect, unauthorized service, or acts of God. It does not cover cosmetic damage or damage due to external causes. It does not apply if the product has been modified or altered.

Warranty Coverage: For warranty service, contact Walmart customer service. If you purchased the product in the United States, warranty coverage is provided. For coverage outside the United States, contact your local retailer or service provider.