DinoFire Wireless Controller Quick Start Guide

Controller Layout

The controller features the following buttons and components:

• Left Side: Left Analog Stick ([L3 button]), D-pad (Up, Down, Left, Right), [L button], [ZL button]
• Right Side: Right Analog Stick ([R3 button]), [Y button], [X button], [A button], [B button], [R button], [ZR button]
• Center: [HOME button], [Capture button], [Turbo button], [- button], [+] button
• Back: [M1 button], [M2 button], [SYNC button], [Vibration button], [Reset button]
• Indicators: LED Indicators (indicating connection status and mode)

Connection Method

I. Connect to Nintendo Switch (NS)

Notice: Please turn off airplane mode. Do not touch the analog sticks while connecting.

1. Enter the connection interface on the NS console (refer to controller diagram for button locations).
2. Press the [SYNC button] on the back of the controller for about 2 seconds until the signal light flashes back and forth. Release your finger and wait for the connection to be successful.

Note: Pressing the [HOME button] can wake up and re-connect the console after the first successful connection.

If unable to connect:

1. Turn off airplane mode.
2. Delete the information of this controller in the NS console: Go to System Settings > Controllers and Sensors > Disconnect Controllers.
3. Follow the first-time connection method and re-pair again.

II. Connect to Android Devices

1. Turn on the Bluetooth function of your Android device and search for devices.
2. Press the [A button] and [HOME button] on the controller simultaneously until LED 1 and LED 2 flash, then release your fingers.
3. On your Android device, find the Bluetooth name "Gamepad", click to pair. LED 1 and LED 2 will remain lit after a successful connection.

Note: This controller supports HID mode games on Android devices. Vibration, screenshot, and motion control functions are not available on Android.

III. Connect to iOS Devices

1. Turn on the Bluetooth function of your iOS device and search for devices.
2. Press the [B button] and [HOME button] on the controller simultaneously until LED 2 and LED 3 flash, then release your fingers.
3. On your iOS device, find the Bluetooth name "Xbox Wireless Controller", click to pair. LED 2 and LED 3 will remain lit after a successful connection.

Note: This controller supports MFI games on iOS devices and requires iOS 13.0 or later. Vibration, screenshot, and motion control functions are not available.

IV. Connect to Windows PC

Wired Connection: Simply connect the controller to your Windows PC using the included USB cable. LED 1 and LED 4 will light up upon successful connection.

Wireless Connection (with receiver):

1. Plug the receiver into a USB port on your computer.
2. Press the [X button] and [HOME button] on the controller simultaneously until LED 2 and LED 3 flash, then release your fingers. Wait for a successful connection; LED 2 and LED 3 will remain lit.

Note: If the connection fails after a long time, unplug the receiver and repeat steps 1 and 2. This controller supports X-INPUT mode games on Windows (Windows 7 and above) and platforms like Steam. Screenshot and motion control functions are not available on Windows.

Special Prompts

• For connection modes I, II, and III, pressing the [HOME button] will reconnect to the most recently connected device.
• On Android, iOS, and Windows PC:
  • Long press the [Capture button] and [L3 button] for about 1 second. The controller will vibrate once, switching the functions of the left analog stick and D-pad.
  • Long press the [Capture button] and [R3 button] for about 1 second. The controller will vibrate once, switching the functions of [A] and [B] buttons, and [X] and [Y] buttons.

Turbo Function

The function buttons that can have Turbo enabled are: [A button], [B button], [X button], [Y button], [L button], [ZL button], [R button], [ZR button].

• Set Manual Turbo: Press and hold the [Turbo button], then press one of the function buttons (e.g., [A button]). The [A button] will now have manual turbo enabled.
• Set Auto Turbo: Press and hold the [Turbo button], then press the function button that already has manual turbo enabled. The button will now have auto turbo enabled.
• Turn Off Turbo: Press and hold the [Turbo button], then press the function button that has auto turbo enabled. The turbo function for that button will be turned off.
• Disable All Turbo: Press the [- button] and the [D-pad DOWN button] simultaneously. The controller will vibrate once, indicating that all turbo functions have been disabled.

There are three levels of Turbo speed:

• Slow: 5 bursts per second (indicated by slow flashing of the signal light).
• Medium: 12 bursts per second (indicated by medium flashing of the signal light).
• Fast: 20 bursts per second (indicated by fast flashing of the signal light).

• Increase Turbo Speed: Press the [Turbo button] and the [Up arrow button] simultaneously. The controller will vibrate once, increasing the turbo speed by one level.
• Reduce Turbo Speed: Press the [Turbo button] and the [Down arrow button] simultaneously. The controller will vibrate once, decreasing the turbo speed by one level.

Vibration Function

There are four levels of vibration strength: None, Weak, Medium, and Strong.

Adjusting Vibration Strength:

1. Ensure the controller is successfully connected to the console.
2. Each time you press the [Vibration button] on the back, you can cycle through the vibration intensity levels.

Programming Setting (Macros)

Reminder: Assign other button's functions to the programmable rear buttons ([M1 button]/[M2 button]).

Programmable Buttons: [A button], [B button], [X button], [Y button], [L button], [ZL button], [R button], [ZR button], [L3 button], [R3 button], and D-pad buttons.

Programming Single Button Steps:

1. With the controller working, press and hold the [- button] and the [M1 button] (or [M2 button]) simultaneously for about 2 seconds. The controller will vibrate once, and the joystick's aperture light will turn white and blink.
2. Press the desired function button (e.g., [A button]).
3. Press the [M1 button] (or [M2 button]) again to save. The controller vibrates once, and the joystick's aperture returns to the normal connection status. The programming for that single button is complete. (Example: Press [-] and [M1] for 2 seconds, joystick aperture blinks white, press [A], then press [M1] to save. The [M1 button] now functions as the [A button].)

Programming Multiple Buttons Steps:

1. With the controller working, press and hold the [+] button and the [M1 button] (or [M2 button]) simultaneously for about 2 seconds. The controller vibrates once, and the joystick's aperture light will turn white and blink.
2. Sequentially press the multiple buttons you want to set (e.g., [B button], then after 1 second press [A button], then after 3 seconds press [X button]). The controller will record the time interval between each button press.
3. Press the [M1 button] (or [M2 button]) again to save. The controller vibrates once, and the joystick's aperture returns to the normal connection status. Programming for multiple buttons is complete. (Example: The [M1 button] will now function as [B button], after 1 second as [A button], and after 3 seconds as [X button].)

You can test the programming success on your console: System Settings > Controllers and Sensors > Test Input Devices > Test Controller Buttons.

Clear Programming:

1. To clear single button programming: Press the [+] button and the [M1 button] (or [M2 button]) simultaneously for about 2 seconds until the joystick's aperture blinks white, then press the [M1 button] (or [M2 button]) to clear that specific button's programming.
2. To clear all macro programming: Press the [Turbo button] and the [- button] simultaneously. The controller will vibrate once, indicating all macros have been cleared.

Lighting Effect Control

• Press the [Light button]: Cycles through fixed light colors.
• Press [Light button] and [+] button: Adjusts to breathing mode or light mode.
• Press [Light button] and [L3 button]: Turns the joystick aperture light effect on or off.
• Press [Light button] and [R3 button]: Turns the panel light effect on or off. (Note: Matte black version does not have panel light effect.)
• Press [Light button] and move the left analog stick up or down: Adjusts the brightness of the joystick aperture light.

Gyro Manual Calibration

If you experience drifting or other joystick issues during gameplay, you can perform manual calibration.

Operation Method:

1. Place the controller on a horizontal surface with the controller powered off.
2. Press the [HOME button] and [- button] simultaneously.
3. Wait for LED 1, LED 2, LED 3, and LED 4 to flash alternately three times.
4. Press the [+] button. The signal light will go out, and calibration is complete.

Service Support

If you encounter any difficulties or product defects during use, please contact the after-sales service through your purchase platform. DinoFire will analyze your feedback promptly to assist with problem resolution or product replacement. Valuable suggestions for product optimization are also welcome. We wish you a pleasant experience.