SpaceLogic™ Room Controllers

1. Safety Information

1.1 Important Information

Read these instructions carefully and inspect the equipment to become familiar with the device before trying to install, operate, service or maintain it. The following special messages may appear throughout this bulletin or on the equipment to warn of potential hazards or to call attention to information that clarifies or simplifies a procedure.

The addition of this symbol [!] to a "Danger" or "Warning" safety label indicates that an electrical hazard exists which will result in personal injury if the instructions are not followed.

This is the safety alert symbol [!] . It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

DANGER: DANGER indicates a hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: CAUTION indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

NOTICE: NOTICE is used to address practices not related to physical injury. The safety alert symbol shall not be used with this signal word.

1.2 Please Note

Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material.

A qualified person is one who has skills and knowledge related to the construction, installation, and operation of electrical equipment and has received safety training to recognize and avoid the hazards involved.

1.3 Before You Begin

Loss of Control

NOTICE

• The designer of any control scheme must consider the potential failure modes of control paths and, for certain critical control functions, provide a means to achieve a safe state during and after a path failure. Examples of critical control functions are emergency stop and over travel stop.
• Separate or redundant control paths must be provided for critical control functions.
• System control paths may include communication links. Consideration must be given to the implications of anticipated transmission delays or failures of the link.
• Each implementation of equipment utilizing communication links must be individually and thoroughly tested for proper operation before being placed into service.

Failure to follow these instructions can result in equipment damage.

Electrostatic Discharge

NOTICE

Static Sensitive Components

Circuit boards and option cards can be damaged by static electricity. Observe the electrostatic precautions below when handling controller circuit boards or testing components.

Failure to follow these instructions can result in equipment damage.

Observe the following precautions for handling static-sensitive components:

• Keep static-producing material such as plastic, upholstery, and carpeting out of the immediate work area.
• Store static-sensitive components in protective packaging when they are not installed in the drive.
• When handling a static-sensitive component, wear a conductive wrist strap connected to the component or drive through a minimum of 1 megohm resistance.
• Avoid touching exposed conductors and components leads with skin or clothing.

Location

NOTICE

• Do not install on an exterior wall.
• Do not install behind a door.
• Do not install in areas with a direct heat source.
• Do not install near any air discharge grill.
• Do not install in areas exposed to direct sunlight.
• Ensure the Room Controller has sufficient natural air circulation.
• Ensure the wall surface is flat and clean.
• Ensure external thermal sensor wirings are away from noisy electrical sources.
• Install 1.3 to 1.5 meters (52 to 60 inches) above the floor.
• Perform preventive maintenance on the damper and Variable Air Volume (VAV) box, according to the supplier documentation.

Failure to follow these instructions can result in equipment damage.

Installation

Unauthorized USB Access

NOTICE

To prevent unauthorized access to the Room Controller via USB, it is recommended that:

• "USB access" is set to "Disabled" to prevent changing of firmware, standby image, configuration or LUA scripts via USB.
• "Main password" is set to a non-zero value to limit configuration menu access to authorized users only.

Failure to follow these instructions may lead to unauthorized users modifying the firmware or the configuration of the Room Controller.

Installation

NOTICE

• The Room Controller is only to be used in conjunction with the VC3000 line voltage switching relay pack. Together they are used as operating controls for high voltage fan coil units.
• The system must be installed correctly by a qualified technician.
• If replacing an existing Room Controller, label wires before removal of the Controller.
• Electronic controls are static sensitive devices. Discharge yourself correctly before manipulating and installing Room Controller.
• A short circuit or wrong wiring may permanently damage the Room Controller or equipment.
• All Room Controllers are designed for use as operating controls only and are not safety devices. These instruments have undergone rigorous tests and verification prior to shipping to ensure proper and reliable operation in the field. Whenever a control failure could lead to personal injury and/or loss of property, it becomes the responsibility of the user/installer/electrical system designer to incorporate safety devices such as relays, flow switches, thermal protections, and/or an alarm system to protect the entire system against any catastrophic failures. Tampering with the devices or unintended application of the devices will result in a void of warranty.
• If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
• These devices are not serviceable and must be returned to the supplier for any repair.
• A switch or circuit breaker must be installed. It must be suitably located, easily reached, and marked as the disconnecting device.
• This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
• This device must be installed to provide a separation distance of at least 8in (20cm) from all persons and must not be located or operating in conjunction with any other antenna or transmitter.
• Refer to the Room Controller User Interface Guide for information on how to configure the Room Controller.

Failure to follow these instructions can result in equipment damage.

Cleaning the Room Controller

NOTICE

• Use a soft, pre-moistened lint-free cloth for cleaning.
• Avoid getting moisture in openings.
• Do not spray anything directly on the Room Controller or use compressed air.
• Do not use caustic/corrosive products, ammonia, solvents or any cleaning product containing alcohol or grit.
• Never use tools directly on the touchscreen.
• Never use paint on the Room Controller.
• Do not drop or crush the Room Controller, or allow it to come into contact with liquids.
• Do not use a damaged device (such as one with a cracked screen).

Failure to comply with these recommendations will result in damage to the unit and void the manufacturer's warranty.

Important Symbols

Products marked with this symbol [!] state that the manuals must be consulted in all cases to any hazards.

Alternating Current [AC symbol]

Direct Current [DC symbol]

Equipment protected throughout by DOUBLE INSULATION or REINFORCED INSULATION [Double Insulation symbol]

Visual Description: The page displays images of the SER8350 Room Controller (a white, rectangular device with a touchscreen interface showing temperature, humidity, and status) and the VC3000 Relay Pack (a black electronic module with multiple terminals and indicator lights).

2. Installation

Visual Description: The page includes three figures illustrating the installation process.

Figure 1: Open the cover - Shows how to open the Room Controller by pulling the bottom side.

Figure 2: Install the base - Depicts the mounting base with screw holes and cable entry, showing alignment with wall mounting holes and cable insertion.

Figure 3: Reinstall cover - Illustrates aligning and snapping the cover back onto the base.

1. Open the unit by pulling on the bottom side of the Room Controller.
2. Read the FCC ID and IC label installed in the cover before installing any wireless product.
3. Ensure the correct side of the base faces up.
4. Pull the cables 6in (15cm) out from the wall.
5. Align the base and mark the location of the two mounting holes on the wall.
6. Install anchors in the wall.
7. Insert the cable in the central hole of the base.
8. Insert screws in the mounting holes on each side of the base.
9. Strip each wire 1/4in (0.6cm) from the end.
10. Insert each wire according to the wiring chart (next page).
11. Gently push the excess wiring back into the hole.
12. Gently align the cover with the top of the base and snap in place from the bottom.
13. Install the security screw.

NOTICE

Disabled Wired Network Protocol

The RS-485 transceiver connected to pins 13 and 14 is not installed on Room Controllers with part number SER8350A5N11, thus disabling the wired network protocol (BACnet MS/TP or Modbus). The network screens and the optional Wi-Fi protocol BACnet/IP will still operate normally.

When ordering, make sure the Room Controller specifications comply with your system design.

3. Terminal Identification and Function

NOTE: Never use any terminal on Room Controller not mentioned in the above table.

4. Communication Wiring to VC3000 Relay Pack

Visual Description: Diagrams show wiring connections between the SER8350 Room Controller and VC3404/VC3300 Relay Packs, illustrating terminal connections for communication, power, and to other relay packs.

Key Points:

• Only one Relay Pack with remote monitoring inputs (VC3404, VC3504, or VC3514) can be used per SER8350. Other Relay Packs must be without remote monitoring inputs (VC3300, VC3400, or VC3500).
• A maximum of 10 Relay Packs can be used per SER8350.
• Relay Packs can be arranged in any order.

4.1 BACnet® Communication Shielded Wiring (If Required)

Wiring Requirements:

• From SER8350 to the first VC3000 Relay Pack: Uses existing or new field wires. A minimum of 3 wires is required. Solid or Stranded, Shield is not necessary. Distance must not exceed 15m (49 ft). Wire gauge depends on distance: AWG 16-18 (1.31 - 0.823 mm²) for <= 10m, AWG 16 (1.31 mm²) for > 10m.
• From the first VC3000 Relay Pack to all other VC3000 Relay Packs: Uses existing or new field wires. 2 required wires: Tx/Rx (Terminal 1) and Power Common (Terminal 3). AWG 16-18 (1.31 - 0.823 mm²). Solid or Stranded, Shield is not necessary.

NOTE: See SER8350 BACnet® integration manual for more details.

4.2 Network Wiring Topology

Visual Description: Diagrams illustrate three network topologies: Star Topology, Daisy Chained Topology, and Mixed Daisy Chained & Star Topology, showing multiple Room Controllers and Relay Packs connected.

NOTE: Only one VC3404, VC3504, or VC3514 Relay Pack with remote monitoring inputs can be used for a single SER8350 Room Controller.

5. Home Screen Display

Visual Description: An illustration of the Room Controller's hospitality user interface is shown, with labels pointing to various display elements:

• Date: e.g., 09.26.2012
• Short Network Message: e.g., Room 1705
• Occupancy Status: e.g., Standby [Standby icon]
• Room Indoor Temperature: e.g., 23.5°C
• Room Indoor Humidity: e.g., 45%
• Outdoor Temperature: e.g., 18°C
• Time: e.g., 12:54 PM
• System Status: e.g., [Heating/Cooling icon]
• Fan Status: e.g., [Fan speed icon]
• Up Arrow: Used to Raise Temperature Setpoint.
• Occupied Setpoint of Current System Mode: Displays the setpoint for the current mode.
• Down Arrow: Used to Lower Temperature Setpoint.
• Help: Enter help screen.
• System Mode: Select system mode (e.g., Auto, Heat, Cool).
• Fan Mode: Select fan mode (e.g., Auto, Low, Medium, High).
• Language: Select preferred language.
• Temperature Units: Select Celsius or Fahrenheit.

NOTE: User HMI is configurable and allows display functions such as Date, Time, Humidity, Outdoor Temperature, Setpoint, and others to be enabled or disabled by setting various parameters.

The outdoor temperature is displayed only on controllers connected to relay packs.

6. Enter Set-up Screen

Visual Description: An image of the Room Controller screen shows the current status. An arrow points to a specific area on the screen.

Touch and hold the indicated point for 3 seconds to enter set-up mode.

NOTE: If a configuration/installer password is activated to prevent unauthorized access to the configuration menu parameters, a password entry prompt shows to prevent access to the device configuration components.

7. Set-up Screen Display

Visual Description: A representation of the set-up menu is shown, with categories like Network, Configuration, Setpoints, Display, Service view, and Test Outputs.

Menu Options:

• Network: Enter BACnet® & Zigbee® network settings.
• Configuration: Enter parameter configuration menu.
• Setpoints: Enter setpoint settings.
• Display: Enter display settings.
• Service view: Enter status display (read only).
• Test Outputs: Enter test outputs settings.

A "Return to the home screen" option is also indicated.

General Note:

• [Adjustable parameter symbol] - Adjustable parameter
• [Non-adjustable parameter symbol] - Non-adjustable parameter

NOTICE

Disabled Wired Network Protocol

The RS-485 transceiver connected to pins 13 and 14 is not installed on Room Controllers with part number SER8350A5N11, thus disabling the wired network protocol (BACnet MS/TP or Modbus). The network screens and the optional Wi-Fi protocol BACnet/IP will still operate normally.

When ordering, make sure the Room Controller specifications comply with your system design.

Appendix A. Deployment

The placement of the Room Controller must be given consideration. It is recommended to install the Room Controller as close to a door as possible (without being blocked by the door), or in an area with high occupant movement.

Ideally, the Room Controller should be installed 5 feet (1.5 meters) above the floor surface to ensure maximum detection range is achieved. As well, Room Controller placement should ensure the occupant crosses the lens beam in a perpendicular path within the prescribed detection zone.

A.1 Example of Recommended Deployment

Visual Description: Diagrams show recommended installation locations for Room Controllers in two rooms (examination room and waiting room). The diagrams illustrate optimal placement relative to doors, traffic flow, and detection zones.

The examination room shows one Room Controller installed adjacent to the door, where occupant traffic is high, ensuring lateral detection.

The waiting room shows one Room Controller installed beside a door in the middle of the room, covering high traffic areas like the entrance, waiting room, and reception desk.

Visual Description: A graphic labeled "Recommended Installation" shows floor plans with shaded areas indicating PIR detection zones.

A.2 Example of Non-Recommended Deployment

Visual Description: Diagrams illustrate non-ideal installation locations for Room Controllers in two rooms. These show controllers placed in low-traffic areas, corners where doors might block detection, or opposite doors where movement is not lateral to the PIR sensor.

The examination room shows controllers in a low-traffic area near the door and on a wall opposite the door. The corner placement may be blocked by doors, and traffic may be minimal. The opposite placement may have detection outside the zone or movement not lateral to the PIR.

The waiting room shows controllers in a corner (risk of PIR blockage by doors) and beside the reception area (occupant traffic outside detection zone, receptionist below recommended height).

Visual Description: A graphic labeled "Non-Recommended Installation" shows floor plans with PIR detection zones indicating potential issues.

A.3 Room Controller PIR Sensor Details

The internal Room Controller PIR sensor only detects lateral movement. It cannot detect movement when a person is moving toward it. It will not detect someone seating on a chair and/or lying on the bed.

Visual Description: A diagram of a room shows the PIR sensor's detection pattern. It indicates lateral movement detection up to 1.5m/s within an 80° horizontal field of view and a range of 6 meters. It also shows a narrower 40° field of view for lateral movement detection at 1.5m/s up to 4-5 meters. The diagram also suggests placement of additional motion sensors.

• Lateral movement of 1.5m/s detected within a range of 6m and 80° field of view.
• Lateral movement of 1.5m/s detected within a range of 4-5m and 40° field of view.
• Areas for potential additional motion sensors are marked.

A.4 Recommendations for Installations

1. Install the Room Controller to cover more lateral movement.
2. Install a door sensor. The internal Room Controller occupancy logic works better with a door sensor. Once a motion is detected after a door is opened, the room stays in an occupied state until the door is opened again, which puts the Room Controller in stand-by mode. If there is motion, it goes back to occupied mode. It is also recommended to disable the unoccupied mode and set the "unoccupied time" to 0, so there are only 2 modes: stand-by and occupied for a stand-alone solution.

Visual Description: Two diagrams illustrate occupancy state transitions:

• 8000 with internal and/or external motion sensors: Shows states like Stand-by, Motion detected, No motion after stand-by time. This logic may cause a bad guest experience if a guest is sleeping or not moving.
• 8000 with door sensor, internal and/or external motion sensors: Shows states like Stand-by, Occupied, Door opened/closed & door closed for at least 15 secs. This logic provides good energy savings and better guest experience.

3. Install additional motion sensors in the bathroom.

4. Install additional motion sensors for better motion detection in the entire room.

A.5 Energy Savings

PIR can maximize your energy saving from 10-30% by adjusting temperature set points in unoccupied zones during scheduled periods.

Visual Description: A line graph titled "Typical Savings of 10-30%" shows Energy Usage (kWh) and Saving Percentage over a 24-hour period. The graph plots "Typical Consumption," "PIR Thermostat Consumption," and "Savings." The savings percentage increases significantly during occupied periods and decreases during unoccupied periods.

Appendix B. California Proposition 65 Warning Statement for California Residents

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm, and Bisphenol A (BPA), which is known to the State of California to cause birth defects or other reproductive harm. For more information, go to www.P65Warnings.ca.gov.

Technical Support and Company Information

For any issues with EcoStruxure Building, contact Schneider Electric Technical Support according to your region.

• North America (NAM) Product Support Building Management Systems (BMS): www.nampss.com
• Global Product Support Building Management Systems (BMS): productsupport.BMS@schneider-electric.com

Schneider Electric CS 30323 F-92506 Rueil-Malmaison Cedex France

Schneider Electric is leading the Digital Transformation of Energy Management and Automation in Homes, Buildings, Data Centers, Infrastructure and Industries. With a global presence in over 100 countries, Schneider is the undisputable leader in Power Management – Medium Voltage, Low Voltage and Secure Power, and in Automation Systems. They provide integrated efficiency solutions, combining energy, automation and software.

In their global Ecosystem, they collaborate with the largest Partner, Integrator and Developer Community on their Open Platform to deliver real-time control and operational efficiency.

They believe that great people and partners make Schneider a great company and that their commitment to Innovation, Diversity and Sustainability ensures that Life Is On everywhere, for everyone and at every moment.

Website: www.schneider-electric.com