PLT Solutions UFO LED High Bay Fixture

⚠️ WARNING

• Installation, service, and maintenance of luminaries should be performed by a qualified licensed electrician.
• Read the installation instructions carefully before installation.

⚠️ CAUTION

• Do not use an electric generator to test this fixture.
• This luminaire must be installed in accordance to the National Electric Code and applicable local codes and ordinances.
• Use a strain relief bushing between the fixture and the outlet box when connecting power wires.
• In the event of smoke or fire, turn off the power immediately and call a licensed electrician.

General Precautions

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards, read all warnings and instructions included with and on the fixture box and all fixture labels.
• Proper grounding is required to ensure safety.
• Power must be turned off at the breaker before installation or maintenance.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Wear gloves and eye protection at all times while installing, servicing, or performing maintenance on the luminaire, and avoid direct eye exposure to the light source while it is on.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not install damaged product. Inspect luminaire for damage that may have occurred during transit. If damaged, contact the manufacturer immediately.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's or owner's purposes, contact the manufacturer.

Installation Instructions

Ring Mount

1. Screw the ring into the top of the fixture and tighten. (Refer to Figure 1: Ring attached to fixture top).
2. Hang the fixture on the ceiling hook or chain. (Refer to Figure 2: Fixture hanging from ceiling).
3. Connect the two ground wires together before connecting the two white neutral wires to each other and the two black wires to each other.

Surface Mount

1. Using the bracket (purchased separately) as a guide, mark the mounting holes on the surface using a marker, then drill guide holes for the mounting screws. (Refer to Figure 3: Marking mounting holes with bracket template, showing approximate 10mm and 100mm dimensions).
2. Screw (by others) mounting screws into the holes.
3. Align the bracket holes with the screw holes and push the fixture to one side. (Refer to Figure 4: Bracket aligned with screw holes; Figure 5: Fixture slid onto bracket).
4. Connect the two ground wires together before connecting the two white neutral wires to each other and the two black wires to each other. By adjusting the bracket screws, the fixture can be vertically adjusted 50° to the left or right. (Refer to Figure 6: Fixture mounted on bracket with 50° adjustment range indicated).

1/2" NPT Mount

1. Unscrew the nuts on the 1/2" NPT fitting (by others). (Refer to Figure 7: 1/2" NPT stem).
2. Insert the 1/2" NPT stem into the bracket (purchased separately) hole. (Refer to Figure 8: 1/2" NPT stem inserted into bracket).
3. Re-screw the nuts to secure the stem. (Refer to Figure 9: Nuts being re-screwed onto stem).
4. Connect the two ground wires together before connecting the two white neutral wires to each other and the two black wires to each other. By adjusting the bracket screws, the fixture can be vertically adjusted 50° to the left or right. (Refer to Figure 10: Fixture mounted via NPT stem and bracket, with 50° adjustment range indicated).

Wiring Diagram

This LED high bay can be switched or dimmed one of three ways:

1. 0-10V dimming
2. PWM signal dimming
3. Variable resistance dimming

Wire Connections:

• Brown/Black: Live (ACL) ⚫
• Blue/White: Neutral (ACN) ⚪
• Green/Yellow: Ground ?
• Purple: DIM+
• Pink: DIM-
• White/Black: AUX+

(Description of Wiring Diagram: The diagram illustrates the connections for Live, Neutral, Ground, DIM+, DIM-, and AUX+ wires to the fixture. The Live wire is Brown/Black, Neutral is Blue/White, Ground is Green/Yellow, DIM+ is Purple, DIM- is Pink, and AUX+ is White/Black.)

Compatible Dimmers

This product has 0-10V dimming. See list of recommended dimmers below: