PLT Solutions UFO LED High Bay Fixture

⚠ WARNING

• Installation, service, and maintenance of luminaries should be performed by a qualified licensed electrician.
• Read the installation instructions carefully before installation.

⚠ CAUTION

• Do not use an electric generator to test this fixture.
• This luminaire must be installed in accordance with the National Electric Code and applicable local codes and ordinances.
• Use a strain relief bushing between the fixture and the outlet box when connecting power wires.
• In the event of smoke or fire, turn off the power immediately and call a licensed electrician.

Installation Instructions

Ring Mount

1. Screw the ring into the top of the fixture and tighten (Figure 1).
2. Hang the fixture on the ceiling hook or chain (Figure 2).
3. Connect the two ground wires together before connecting the two white neutral wires to each other and the two black wires to each other.

Figure 1: Shows a threaded ring being screwed into the top of the UFO LED High Bay Fixture.

Figure 2: Depicts the fixture hanging from a ceiling hook or chain via the installed ring.

Surface Mount

1. Using the bracket (purchased separately) as a guide, mark the mounting holes on the surface using a marker, then drill guide holes for the mounting screws (Figure 3).
2. Screw (by others) mounting screws into the holes.
3. Align the bracket holes with the screw holes (Figure 4), and push the fixture to one side (Figure 5). Tighten the screws to secure the fixture.
4. Connect the two ground wires together before connecting the two white neutral wires to each other and the two black wires to each other. By adjusting the bracket screws, the fixture can be vertically adjusted 50° to the left or right (Figure 6).

Figure 3: Illustrates marking mounting holes on a surface using a bracket as a guide, followed by drilling pilot holes.

Figure 4: Shows aligning the fixture's bracket holes with the pre-drilled mounting screw holes.

Figure 5: Demonstrates pushing the fixture sideways to engage mounting screws and secure it to the bracket.

Figure 6: Displays the fixture mounted, with an indication that the bracket allows for vertical adjustment of up to 50 degrees to the left or right.

1/2" NPT Mount

1. Unscrew the nuts on 1/2" NPT (by others) (Figure 7).
2. Insert 1/2" NPT stem into the bracket (purchased separately) hole (Figure 8).
3. Re-screw the nuts (Figure 9).
4. Connect the two ground wires together before connecting the two white neutral wires to each other and the two black wires to each other. By adjusting the bracket screws, the fixture can be vertically adjusted 50° to the left or right (Figure 10).

Figure 7: Shows two nuts on a 1/2" NPT threaded stem, labeled A and B.

Figure 8: Illustrates inserting the 1/2" NPT stem into the fixture's mounting bracket.

Figure 9: Depicts screwing the nuts onto the 1/2" NPT stem to secure it to the bracket.

Figure 10: Shows the fixture mounted using the 1/2" NPT connection, with an indication of vertical adjustment capability (50° left/right).

Wiring Diagram

This LED high bay can be dimmed using 0-10V dimming.

Connect the driver PURPLE wire (D+) to the DIMMER+ (PURPLE) wire and the driver PINK (D-) wire to the DIMMER- (PINK) wire using wire nuts (supplied by others).

Diagram Description: The wiring diagram shows the fixture's wires connecting to a power source and dimmer. The fixture has wires: Green/Yellow (Ground), Brown/Black (ACL - Live), Blue/White (ACN - Neutral), Purple (DIM+), and Pink (DIM-). The diagram indicates connecting Green/Yellow to Ground, Brown/Black to Live (ACL), Blue/White to Neutral (ACN), Purple wire to the dimmer's positive (DIM+) terminal, and Pink wire to the dimmer's negative (DIM-) terminal.

Compatible Dimmers

This product has 0-10V dimming. See list of recommended dimmers below:

General Safety Precautions

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards, read all warnings and instructions included with and on the fixture box and all fixture labels.
• Proper grounding is required to ensure safety.
• Power must be turned off at the breaker before installation or maintenance.
• This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product and the hazards involved.
• Wear gloves and eye protection at all times while installing, servicing, or performing maintenance on the luminaire, and avoid direct eye exposure to the light source while it is on.
• To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
• Do not install damaged product. Inspect luminaire for damage that may have occurred during transit. If damaged, contact the manufacturer immediately.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in connection with installation, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser's or owner's purposes, contact the manufacturer.