Midea Cooker Hood

Thank You Letter

Thank you for choosing Midea! Before using your new Midea product, please read this manual thoroughly to ensure that you know how to operate the features and functions that your new appliance offers in a safe way.

Contents

• Thank You Letter
• Safety Instructions
• Specifications
• Product Overview
• Product Installation
• Operation Instructions
• Cleaning and Maintenance
• Trouble Shooting
• Trademarks, Copyrights and Legal Statement
• Disposal and Recycling
• Data Protection Notice

Safety Instructions

Intended Use

The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect operation of the appliance. Please check the packaging and appliance on arrival to make sure everything is intact to ensure safe operation. If you find any damage, please contact the retailer or dealer. Please note modifications or alterations to the appliance are not allowed for your safety concern. Unintended use may cause hazards and loss of warranty claims.

Explanation of Symbols

• Danger: This symbol indicates that there are dangers to the life and health of persons due to extremely flammable gas.
• Warning of electrical voltage: This symbol indicates that there is a danger to life and health of persons due to voltage.
• Warning: The signal word indicates a hazard with a medium level of risk which, if not avoided, may result in death or serious injury.
• Caution: The signal word indicates a hazard with a low degree of risk which, if not avoided, may result in minor or moderate injury.
• Attention: The signal word indicates important information (e.g. damage to property), but not danger.
• Observe instructions: This symbol indicates that a service technician should only operate and maintain this appliance in accordance with the operating instructions.

Read these operating instructions carefully and attentively before using/commissioning the unit and keep them in the immediate vicinity of the installation site or unit for later use!

WARNING

The instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. (EN 60335-1 & EN 60335-2-31)
• Children shall not play with the appliance. (EN 60335-1 & EN 60335-2-31)
• Cleaning and user maintenance shall not be made by children without supervision. (EN 60335-1 & EN 60335-2-31)
• If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• This appliance incorporates an earth connection for functional purposes only.
• There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• There is a fire risk if cleaning is not carried out in accordance with the instructions; Do not flambé under the range hood.
• CAUTION: Accessible parts may become hot when used with cooking appliances.
• The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room).
• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood is 650 mm.
• Regulations concerning the discharge of air have to be fulfilled.
• The appliance uses 4 hob elements at most.
• The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
• Check that the mains voltage corresponds to that indicated on the rating plate fixed to the hood.
• For Class I appliances, check that the domestic power supply guarantees adequate earthing.
• Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm.
• The route of the flue must be as short as possible.
• Do not connect the extractor hood to exhaust ducts carrying combustion flumes (boilers, fireplaces, etc.).
• If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account.

Specifications

Product Overview

Components

Optional Installation Components

Dimensions

unit: mm

A diagram showing the dimensions of the cooker hood and its installation requirements. The diagram includes measurements for width, depth, height, and clearance from the hob.

Product Installation

Wall Drilling And Bracket Fixing

A diagram illustrating the process of drilling holes and fixing brackets for the cooker hood installation. It shows measurements for horizontal and vertical lines, and the placement of fixing points.

As a first step, proceed with the following drawings:

• I line up to the ceiling or up to the upper limit, at the center of the area in which the hood is to be fitted.
• A horizontal line A at 970 – 1070 mm above the cooker top.
• A horizontal line B at a X mm above the horizontal line A.
• A horizontal line C at a 243 mm below the horizontal line A.

Mark Points:

• Mark a point (1) on the horizontal line A, 80 mm to the vertical reference line. Repeat this operation on the other side and on the vertical reference line, checking that the three marks are leveled.
• Mark a point (2) on the horizontal line B, 60 mm to the vertical reference line. Repeat this operation on the other side, checking that the two marks are on the same horizontal line.
• Mark a point (3) on the horizontal line C, 100 mm to the vertical reference line. Repeat this operation on the other side, checking that the two marks are leveled.

Fix the brackets:

• Drill holes at the marked points with a ∅10 mm drill bit.
• Insert the Wall Plugs 11 into the holes.
• Fix the hood fixing bracket 20 with 3 screws 10 (5 x 50) at the horizontal line A.
• Fix a Chimney fixing bracket 21 with 2 screws 10 (5 x 50) at the horizontal line B.

Lower Decorative Chimney

Fix the exhaust pipe on the hood body, connect chimney and hood body with 2 screws 12. Connect chimney fixing bracket and chimney with 2 screws 12.

A diagram showing how to attach the lower decorative chimney.

Hook The Hood Body

• Hook the hood body to the bracket 20.
• Level the hood body itself.
• Remove the filter from the inside of the hood body, fix the screws 10 to Wall Plugs 11 at the points (3).

Diagrams showing the correct and incorrect ways to hook the hood body.

Connections

When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ∅150 or ∅120 mm, the choice of which is left to the installer.

• If to install a ∅120 mm air exhaust connection, insert the reducer flange 3 on the hood body outlet.
• Fix the pipe 4 in position using sufficient pipe clamps (not supplied).
• Remove possible charcoal filters.

Upper Decorative Chimney

• Insert the upper decorative chimney 2.2 into the lower decorative chimney 2.1 and drag it up to the horizontal line B.
• Connect upper decorative chimney 2.2 and chimney fixing bracket 21 with 2 screws 12.

A diagram showing the connection of the upper decorative chimney.

Operation Instructions

Speed Adjustment. (For Some Models)

A diagram of the control panel with buttons for lighting, speed adjustment, and power. A table details the function of each button.

Cleaning and Maintenance

Grease Filters

CLEANING METAL SELF-SUPPORTING GREASE FILTERS

• The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
• Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards.
• Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make sure that they are completely dry. (The color of the filter surface may change throughout the time but this has no influence to the filter efficiency).
• When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing outwards.

Activated Charcoal Filter (Recirculation Version)

• These filters are not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently with heavy usage.

Replacing The Activated Charcoal Filter

• Remove the metal grease filters.
• Remove the saturated activated charcoal filter.
• Fit the new filters.
• Replace the metal grease filters.

A diagram illustrating the process of replacing the activated charcoal filter.

Lighting

LIGHT REPLACEMENT (Completed by professionals)

Replacing the light modules

• Cannot replaced the light bulbs, the entire light module has to be replaced.
• When changing the light modules, the contacts are live.
• Before changing the light module(s), unplug the appliance from the mains or switch off the circuit breaker in the fuse box.
• Remove the grease filter and carefully remove the 2 screws from the front plate (a cross headed screwdriver will be needed to remove the screws).
• Disconnect the terminal of LED light.
• Press LED light on the back of the front plate, take the LED light out.
• Replace the lamp (commercially available LED lamp (max.1.5W).

• Press LED light on the front of front plate, install the LED light on the front plate.
• Connect the terminal of LED light and light leads.
• Carefully fasten the 2 screws on the front plate, reinstall the grease filter.

Troubleshooting

Trademarks, Copyrights and Legal Statement

Midea logo, word marks, trade name, trade dress and all versions thereof are valuable assets of Midea Group and/or its affiliates (“Midea”), to which Midea owns trademarks, copyrights and other intellectual property rights, and all goodwill derived from using any part of an Midea trademark. Use of Midea trademark for commercial purposes without the prior written consent of Midea may constitute trademark infringement or unfair competition in violation of relevant laws.

This manual is created by Midea and Midea reserves all copyrights thereof. No entity or individual may use, duplicate, modify, distribute in whole or in part this manual, or bundle or sell with other products without the prior written consent of Midea.

All the described functions and instructions were up to date at the time of printing this manual. However, the actual product may vary due to improved functions and designs.

Disposal and Recycling

Important instructions for environment

Compliance with the WEEE Directive and Disposing of the Waste Product:

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).

This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used device must be returned to official collection point for recycling of electrical electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was purchased. Each household performs important role in recovering and recycling of old appliance. Appropriate disposal of used appliance helps prevent potential negative consequences for the environment and human health.

Compliance with RoHS Directive

The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

Package information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

♻️

Data Protection Notice

For the provision of the services agreed with the customer, we agree to comply without restriction with all stipulations of applicable data protection law, in line with agreed countries within which services to the customer will be delivered, as well as, where applicable, the EU General Data Protection Regulation (GDPR).

Generally, our data processing is to fulfil our obligation under contract with you and for product safety reasons, to safeguard your rights in connection with warranty and product registration questions. In some cases, but only if appropriate data protection is ensured, personal data might be transferred to recipients located outside of the European Economic Area.

Further information are provided on request. You can contact our Data Protection Officer via MideaDPO@midea.com. To exercise your rights such as right to object your personal date being processed for direct marketing purposes, please contact us via MideaDPO@midea.com. To find further information, please follow the QR Code.