Instruction Manual for Midea models including: 60L07, Cooker Hood, 60L07 Cooker Hood
User Manuals | Asters Maldives
File Info : application/pdf, 12 Pages, 519.10KB
DocumentDocumentCOOKER HOOD INSTRUCTION MANUAL Read this manual carefully before operation Pictures in this manual are for reference only, the product in kind prevail. 60L07 RECOMMENDATIONS AND SUGGESTIONS The instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. The minimum safety distance between the cooker top and the extractor hood is 650 mm (some models can be installed at a lower height, please refer to the paragraphs on working dimensions and installation). Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood. For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust flue through a pipe of minimum diameter 120mm. The route of the flue must be as short as possible. Do not connect the extractor hood to exhaust ducts carrying combustion flumes (boilers, fireplaces, etc.). If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances),a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. The kitchen must have an opening communicating directly with the open air in order to guarantee the entry of clean air. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker hood. In the event of damage to the power cable, it must be replaced by the manufacturer or by the technical service department, in order to prevent any risks. If the instructions for installation for the gas hob specify a greater distance specified above, this has to be taken into account. Regulations concerning the discharge of air have to be fulfilled. USE The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells. Never use the hood for purposes other than for which it has been designed. Never leave high naked flames under the hood when it is in operation. Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides. Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames. Do not flame under the range hood; risk of fire. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. "CAUTION: Accessible parts may become hot when used with cooking appliances". MAINTENANCE Switch off or unplug the appliance from the mains supply before carrying out any maintenance work. Clean and/or replace the Filters after the specified lime period (Fire hazard). Clean the hood using a damp cloth and a neutral liquid detergent. The appliance uses 4 hob elements at most. The symbol is packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. 2 COMPONENTS Ref. Qty. Product Components 1 1 Hood Body, complete with: Controls, Light, Blower, Filter. 1 2 4 Screws 5 x 50 3 4 Wall Plugs 3 3 2 2 3 DIMENSIONS unitmm 280 255 136 595 527 Min. Min. 650 43 240 75 595 25 480 400 255 40 280 136 4 INSTALLATION METHOD 1 240 75 480 400 595 25 255 40 280 136 According to the figure, make sure the position of hood in the cabinet. The wood strips should be line up with the 4 keyholes slots on the top of the range hood. On the cabinet, install 4 screws (supplied) according to the relative position of 4 key holes on the bottom of hood. The extent of screwing should be convenience to the next installation. Hang the hood and let it's 4 key holes aim at screws, the 4 screws should be in the narrow parts of key holes. Screws should be fasten firmly, make sure that the installation between the hood and cabinet is enough fasten. Install screws in the security holes, in case of front and back moving of hood, so that the using is safer. Information When cutting or drilling into wall or ceiling, do not damage electrical wiring or other hidden utilities. METHOD 2 235 75 400 5 z In the installation surface in cabinet don't adapt to install the cooker hood, then as per fig, fix the position of cooker hood on the wall. z On the wall, install 2 screws ( supplied ) according to the relative position of 2 key holes on the back of hood. z The extent of screwing should be convenience to the next installation. z Also install screws in the security holes, in case of front and back moving of hood, so that the using is safer. Installation of hoods built in combi cabinets is the same as previous method. Information Congratulations on the purchase our cooker hood which is designed to include many superior features that permit you the fullest expression of your living. Before installing and/or using the cooker hood carefully read all the instruction. Right Wrong Information The cooker hood must not be installed and connected to flues where other appliances are installed and which run off other energy supplied different to electricity(water heater boiled cookers(range/agas)etc.). 6 CHOOSE A VENTING MODE Here two venting modes, extraction-air mode and recirculation mode, before installing should be select one of them. Extraction-air mode, the air is discharged out of the house by a pipe. Recirculation mode, the air is purified and discharged into the house. Recirculation mode Extraction-air mode Information Recirculation mode, the cabinet needs an air vent. Recirculation mode, always be with activated carbon filter. Recirculation mode, when activated carbon filter attached, the suction power will be lowered. CONNECTIONS DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe 150 or 120 mm, the choice of which is left to the installer. To install a 120 mm air exhaust connection, insert the reducer flange 3 on the hood body outlet. Fix the pipe 4 in position using sufficient pipe clamps (not supplied). Remove possible charcoal filters. 7 USE Operation Check beforehand Check the safe condition of the appliance Check whether there are visible defects. Check that all parts of the appliance have been securely fitted. Switching on/off In the right part of the cooker hood. (For some models) There are 2 speeds for the motor and on off switch of the lamp. Locker switch for operation. Motor Operation [ ]=Off [ ]=Low Power Setting [ ]=High Power Setting Light Operation [ ]=Off [ ]=On 8 MAINTENANC GREASE FILTERS CLEANING METAL SELF-SUPPORTING GREASE FILTERS The filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. Pull the comfort panels to open them. Remove the filters one by one pushing them towards the back side of the hood unit and simultaneously pulling downwards. Any kind of bending of the filters has to be avoided when washing them. Before fitting them again into the hood make sure that they are completely dry. (The color of the filter surface may change throughout the time but this has no influence to the filter efficiency). When fitting the filters into the hood pay attention that they are mounted in correct position the handle facing outwards. Close the comfort panel. ACTIVATED CHARCOAL FILTER (RECIRCULATION VERSION) REPLACING THE ACTIVATED CHARCOAL FILTER These filters are not washable and cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently with heavy usage. REPLACING THE ACTIVATED CHARCOAL FILTER Remove the metal grease filters Remove the saturated activated charcoal filter. Fit the new filters. Replace the metal grease filters. 9 LIGHTING LIGHT REPLACEMENT Changing the light Lightning inside the appliance is provided by a 1.5W LED light. To replace the LED light, proceed as follows: 1. Disconnect the appliance from the mains or switch off the circuit breaker. 2. Remove the metal filters (see Cleaning and Replacing Filters) . 3. Remove the light by levering its fitting from the hood body(this may require pressure or force to be applied) and disconnect the connector of the light. 4. Replace the light with a n ew one of the same type, making sure that you connect the light with the light cable correctly. 5. Install the metal filter back in place. Max power Voltage Picture Lamp Cap ILCOS D code Self-ballasted LED modules 1.5W 220-240V / Square/Diameter:33.2mmx120mm DBS-1.5H-33.2/120 DISPOSAL OF OLD ELECTRICAL APPLIANCES The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately in order to optimize the recovery and recycling of the materials they contain, and reduce the impact on human health and the environment. The crossed out "wheeled bin" symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance. 10 TROUBLE SHOOTING Fault Light on, but motor does not work Both light and motor do not work Oil leakage Vibration Cause The blades are blocked. The capacitor is damaged. The motor is damaged. Solution Replace capacitor. Replace motor. The internal wiring of motor is cut off/ disconnected. An unpleasant smell Replace motor. may be produced. Apart from the above mentioned, check the following: Light damaged. Replace lights. Power cord loose. Connect the wires as per the electric diagram. Outlet and the air ventilation entrance Take down the outlet and seal with glue. are not tightly sealed. Leakage from the connection of U-shaped section and cover. Take U-shaped section down and seal with soap or paint. The blade, if damaged, can cause vibrating. Replace the blade. The motor is not tightly fastened. Fasten the motor tightly. The cooker hood is not tightly fixed. Fixed the cooker hood tightly. Insufficient suction The machine inclines The distance between the cooker Readjust the distance. hood and the cooker top is too large. Too much ventilation from open doors Choose a new place to install the or windows. appliance or close some doors / windows. The fixing screws are not tight enough. Tighten the fixing screw and make it horizontal. The hanging screws are not tight enough Tighten the hanging screw and make it horizontal. 11 The manufacturer shall decline all responsibility if the foregoing recommendations and instruction regarding installation, maintenance and use are not observed and respected when using the cooker hood. P/N:16173000A17465Microsoft Word 2010 3-Heights(TM) PDF Optimization Shell 5.9.1.5 (http://www -tools.com)