Version History
| Version | Date | Description |
|---|---|---|
| 1.0 | October 11, 2024 | Preliminary user guide for device launch. |
| 1.1 | October 18, 2024 | Updated package content. |
Introduction
The U-BRIDGE 3 is a USB 3.2 Gen 1 extension over CAT6A that can extend a 5Gbps signal between a host and devices. This is a two-boxes solution, which are called PCHOST and DEVICE modules.
Connectivity Diagram
Here is a simple U-BRIDGE 3 connectivity diagram. You can plug the power supply to any module to power up the whole system.
Diagram Description: A PC host is connected to the INOGENI U-BRIDGE 3 PC HOST module via USB. The PC HOST module is connected to the INOGENI U-BRIDGE 3 DEVICE module using a single CAT6A cable, enabling USB 3.2 Gen 1 signal extension up to 100 meters (330 feet). The DEVICE module then connects to various USB devices.
Device Interfaces
Here are the device interfaces for the PC HOST and DEVICE modules.
PC HOST Module Interfaces:
- 1: +24VDC power input. If power supply is connected here, the DEVICE side will be powered using PoC (Power over Cable) through the HDBaseT link.
- 2: HDBaseT link.
- 3: RS232 connection.
- 4: USB-C host connection.
- 5: USB-mini management connection.
DEVICE Module Interfaces:
- 6: +24VDC power input. If power supply is connected here, the DEVICE will be powered locally.
- 7: HDBaseT link.
- 8: RS232 connection.
- 9: USB-C device connection.
- 10: USB-A device connection.
- 11: USB-A device connection.
- 12: USB-mini management connection.
LEDs Behavior
Here are the LEDs behavior on the HDBaseT link connection:
| LED | State | Description |
|---|---|---|
| GREEN LED | OFF | No power. |
| SOLID | System powered with USB connection detected. | |
| BLINK | System powered with no USB connection detected. | |
| ORANGE LED | OFF | No HDBaseT connection detected. |
| SOLID | HDBaseT connection detected. |
Specifications
Here is the complete specification.
| Feature | Description |
|---|---|
| Main feature | The U-BRIDGE 3 USB 3.2 Gen 1 extender enables superspeed USB 3.0 connection of up to 100m/330ft over a single CAT6A. |
| Range | Direct connect up to 100m (330ft) over CAT6A U/FTP. |
| USB speeds | USB 3.2 Gen1 / USB 3.1 Gen1 / USB 3.0: up to 5 Gbps; USB 2.0: up to 480 Mbps. |
| USB transfers support | Bulk, isochronous, interrupt and control types; Built-in hardware acceleration for isochronous and bulk transfers. |
| PC Host extender | |
| USB connector | 1 x USB Type-C receptacle with mounting screw hole. |
| Link connector | 1 x RJ45. |
| Dimensions (W x L x H) | 7.0 cm x 9.7 cm x 2.3 cm (2.76" x 3.82" x 0.90"). |
| Weight | 170 g (0.37 lb). |
| Mounting | Bracket provided. |
| Enclosure material | Black anodized aluminum case. |
| RS232 connector | Passthrough serial connection. By default, I/O pin is an input (+1.8V logic maximum). |
| Device extender | |
| USB connector | 2 x USB-A receptacles. |
| Link connector | 1 x USB-C receptacle with mounting screw hole. |
| Available current | Up to 1.8A shared between ports. |
| Dimensions (W x L x H) | 7.0 cm x 13.7 cm x 2.3 cm (2.76" x 5.39" x 0.90"). |
| Weight | 210 g (0.46 lb). |
| Mounting | Bracket provided. |
| Enclosure material | Black anodized aluminum case. |
| RS232 connector | Passthrough serial connection. By default, I/O pin is an output (GND or OPEN). |
| Physical details | |
| Package dimensions | 24.5 cm x 25 cm x 7.9 cm (9.69" x 9.84" x 3.11"). |
| Power supply | 100-240V AC Input, 24V 1.5A DC output. Apply at either PC HOST or DEVICE modules. |
| Package weight | 1200 g (2.65 lbs). |
| Package contents | 1x PC Host extender module, 1x Device extender module, 1x USB 3.0 Type-C to Type-C cable, 1x Quick Start Guide, 2x mounting brackets (power supply), 2x mounting clips, 2x terminal blocks, 4x black wooden screws, 1x power supply 100-240V AC Input, 24V 1.5A DC output, International power adapter with country-specific cord (North America, EU, UK, Australia/NZ, or Japan). |
| Operating temperature | 0°C to 50°C (32°F to 122°F). |
| Storage temperature | -20°C to 70°C (-4°F to 158°F). |
| Operating humidity | 20% to 80% relative humidity, non-condensing. |
| Storage humidity | 10% to 90% relative humidity, non-condensing. |
Serial Connection
Here is the serial connection of the U-BRIDGE 3. A serial port from a DUT (Device Under Test) can be extended when using this device.
Pinout of the serial connection:
- Pin 1: Receive
- Pin 2: GND
- Pin 3: Transmit
- Pin 4: I/O
The direction of the I/O pin can be configured through the Maestro software.
? NOTE: By default, the PC HOST I/O pin is an input and the DEVICE I/O pin is an output.
INOGENI Maestro Application
You can use the INOGENI Maestro application to monitor firmware information, link status, and upgrade your units.
? NOTE: You can use the Maestro software when the kit (PCHOST / CAT6A cable / DEVICE) is connected to your computer using the USB-C connection on the PCHOST module. You can also use the USB-mini connector to upgrade the modules.
This is a preview of the upcoming Maestro application. More detailed configurations will be added to an updated version of the user guide.
Application Preview Description: The INOGENI Maestro application interface displays detected devices, specifically the U-BRIDGE 3. It shows general information such as firmware versions for PC HOST and DEVICE, serial number, link status (Link, Active/Inactive), estimated distance, and signal integrity (OK for Pairs A, B, C, D).
Mechanical Specification
You can find the mechanical specification of the device. All dimensions are in mm [in].
PCHOST MODULE
Diagram Description: The PC HOST module is depicted from multiple angles, including isometric views and a top-down view showing dimensions. Key dimensions are approximately 97.00 mm [3.819 in] in length, 70.00 mm [2.756 in] in width, and 24.00 mm [0.945 in] in height. Ports visible include the RJ45 link connector, RS232 connector, USB-C host port, and power input.
DEVICE MODULE
Diagram Description: The DEVICE module is shown from multiple angles, similar to the PC HOST module. Key dimensions are approximately 136.32 mm [5.367 in] in length, 70.00 mm [2.756 in] in width, and 24.00 mm [0.945 in] in height. Ports visible include two USB-A device ports, one USB-C port, the RJ45 link connector, RS232 connector, and power input.
INO - CLIP
Diagram Description: This section details bracket dimensions and installation methods for the U-BRIDGE 3. It includes diagrams for a bracket, a support component, and methods for supporting the U-BRIDGE ASSY (both DEVICE and HOST) using screws. Dimensions for various bracket parts are provided.
Power Supply
Diagram Description: This section illustrates the power supply unit and its associated mounting bracket. The power supply unit itself has dimensions of approximately 79 mm [3.110 in] in length and 33 mm [1.299 in] in width. The mounting bracket is shown with dimensions of approximately 73.00 mm [2.874 in] in length and 54.75 mm [2.156 in] in width, designed to hold the power supply.
Troubleshooting Section
Here is the troubleshooting section for the device.
| Problem | Resolution |
|---|---|
| Green LED is blinking slow, Orange LED is OFF | PC HOST side is not connected to a PC or HDBaseT cable is not working properly. |
| Green LED is blinking slow, Orange LED is ON | PC HOST side is not connected to a PC. |
| Green LED is blinking fast | There is a firmware problem. Connect the USB-C PC HOST port and mini-USB management port to a PC running Maestro for firmware upgrade. |
| Green LED is OFF, Orange LED is OFF | PC HOST side: No power from the USB-C port of the host PC. DEVICE side: No power to the 24VDC port on either HOST side (via PoC) or DEVICE side (direct), or HDBaseT cable is not connected or not working properly if using PoC. |
| Unstable USB 3.0 connection | HDBaseT cable is too long or not working properly. USB cables are too long or not working properly. |
| USB 3.0 ports are shutting down | Too much power drawn on USB ports; the maximum current consumption is 1.8A total for the 3 ports. |
| Using a USB-C to USB-A adapter, my USB 3.0 devices are detected in USB2.0 mode only on my computer. | Most passive USB-C to USB-A adapters support USB3.0 on one side of the USB-C connection. Flip by 180 degrees the USB-C connection next to the adapter to see if this resolves the issue. |
Support
Engineered by video professionals, for video professionals, this is your most compatible USB 3.0 device. INOGENI expertise is at your fingertips:
- Expert Technical Support team at support@inogeni.com for immediate help or if you have any technical question about our products.
- Extensive Knowledge Base to learn from other customers' experiences.
Copyright © 2024 by INOGENI INC. All Rights Reserved.
INOGENI name and logo are trademarks or registered trademarks of INOGENI. Use of this product is subject to the terms and conditions of the license and limited warranty in effect at the time of purchase. Product specifications can change without notice.
INOGENI, Inc.
1045 Avenue Wilfrid-Pelletier
Suite 101
Québec, QC, Canada, G1W0C6
(418) 651-3383
Certifications
FCC Radio Frequency Interference Statement Warning: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received including interference that may cause undesired operation.
IC Statement: This Class A digital apparatus complies with Canadian CAN ICES-3(A)/NMB-3(A).
CE Statement: We, INOGENI Inc., declare under our sole responsibility that the Toggle Rooms, to which this declaration relates, is in conformity with European Standards EN 55032, EN 55035, and RoHS Directive 2011/65/EU + 2015/863/EU.
UKCA Statement: This device is compliant with the Electromagnetic Compatibility Regulations 2016 No. 1091 as part of the requirements leading to the UKCA marking.
WEEE Statement: The European Union has established regulations for the collection and recycling of all waste electrical and electronic equipment (WEEE). Implementation of WEEE regulations may vary slightly by individual EU member states. Please check with your local and state government guidelines for safe disposal and recycling or contact your national WEEE recycling agency for more information.
RCM Statement: This device is compliant with Regulator Compliance Mark (RCM) certification.
mailto:support@inogeni.com
