Brookstone Wireless Cat Ear Headphones

Important Safety Information

All safety and operating instructions should be read, heeded, adhered to, and followed before the unit is operated.

LITHIUM-ION BATTERY WARNINGS

This device contains a non-removable Lithium-Ion battery. The battery must be recycled or disposed of properly. Contact your local waste management office for information on battery recycling or disposal. [battery-recycling-symbol]

WARNING

1. Close supervision is necessary when this appliance/product is used by or near children or mentally disabled individuals.
2. Use this unit only for its intended use as described in this manual.
3. Unplug this unit during lightning storms or when unused for long periods of time.
4. Never drop or insert an object into any opening.
5. Protect the power cord from being walked on or pinched, particularly at plug outlets, convenience receptacles, and the point where it exits the unit.
6. Do not allow the cord to touch hot surfaces. Wrap the cord loosely around the unit when storing.
7. The unit should be situated away from direct sunlight or heat sources such as radiators, electric heaters, heat registers, stoves, or other units (including amplifiers) that produce heat. Avoid placing on top of stereo equipment that radiates heat.
8. Do not overload the electrical outlet. Use only the power source as indicated.
9. Do not carry this unit by its cord or use the cord as a handle.
10. Never operate this unit if it has a damaged cord or plug, if it is not working properly, or if it has been dropped or damaged, or dropped into water. If the unit's power supply cord or plug is damaged, do not attempt to fix it yourself.
11. To avoid the risk of electric shock, do not disassemble or attempt to repair the unit. Incorrect repair can cause risk of electric shock or injury to persons when the unit is used.
12. Do not operate in the presence of explosive and/or flammable fumes.
13. Never remove the plug from the outlet by pulling the power cord.

FCC Information

This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the distance between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This equipment may not cause harmful interference.
2. This equipment must accept any interference received, including interference that may cause undesired operation.

Modifications not authorized by the manufacturer may void the user's authority to operate this device.

Location of Parts and Controls

Headphones:

• 1. Speaker with Light (2)
• 2. Right Ear Cup
• 3. Ear Cup Light (2)
• 4. Left Ear Cup

Cables and Buttons:

• 5. 3.5mm to 3.5mm Headphone Cord with inline microphone
• 6. Play/Pause/Track Forward/Track Back Button (on cord)
• 7. Micro USB Charging Cable

Right Ear Cup (Bottom Controls):

• 8. Light On/Off/Choose Color Button
• 9. Light Mode Button
• 10. Speakers On/Off Button
• 11. Headphone Cord Input
• 12. Volume + Button
• 13. Play/Pause/Track Forward/Track Back Button (on ear cup)

Right Ear Cup (Top Controls):

• 14. Volume - Button
• 15. Pairing/Charging LED Indicator
• 16. Micro USB Input
• 17. Bluetooth® Button

Diagrams show the physical layout of buttons and ports on the headphones.

Charging the Cat Ear Headphones

1. Use the included MICRO USB CHARGING CABLE to charge the headphones with a USB adapter (5V, 1A or above) (not included). The headphones will be fully charged in approximately 3 hours.
2. The CHARGING LED INDICATOR is red while the headphones are charging and turns off when fully charged.
3. When the battery is low, the CHARGING LED INDICATOR will flash red (not in Bluetooth® mode) or flash red and blue (in Bluetooth® mode).

Pairing Your Device

1. Prepare your device to pair using Bluetooth® wireless technology, ensuring you are within 33 feet of the headphones. Refer to your device's owner's manual for details.
2. Press and hold the BLUETOOTH BUTTON until the PAIRING LED INDICATOR illuminates and four tones sound to turn Bluetooth® mode on.
3. The PAIRING LED INDICATOR will be solid blue for 5 seconds while the headphones search for previously paired devices. If no connection is made within 5 seconds, the headphones enter Bluetooth® pairing mode, indicated by a flashing blue light and two tones.
4. Once the headphones are in pairing mode and your device is ready, select "Cat Headphones" on your device. If prompted, use 0000 as a PIN. The PAIRING LED INDICATOR will change to solid blue and one tone will sound upon successful pairing.

Notes:

• After initial pairing, the headphones should automatically pair with your device when Bluetooth® mode is activated. You may need to select "Cat Headphones" in your device's Bluetooth® menu.
• To cancel pairing mode, press the BLUETOOTH BUTTON to turn off Bluetooth® mode, or wait 5 minutes for the headphones to automatically cancel pairing mode. The PAIRING LED INDICATOR will turn off.
• If ear cups and speaker lights are on, they turn off if pairing mode is cancelled automatically. Press the LIGHTS ON/OFF/CHOOSE COLOR BUTTON to turn them back on.

Listening to Audio

1. Press and hold the BLUETOOTH BUTTON until the PAIRING LED INDICATOR illuminates to turn Bluetooth® mode on.
2. Press the VOLUME + BUTTON to increase audio volume.
3. Press the VOLUME - BUTTON to decrease audio volume.
4. Press the PLAY/PAUSE/TRACK FORWARD/TRACK BACK BUTTON once to play or pause audio.
5. Press the PLAY/PAUSE/TRACK FORWARD/TRACK BACK BUTTON twice in quick succession to move one track forward.
6. Press the PLAY/PAUSE/TRACK FORWARD/TRACK BACK BUTTON three times in quick succession to move one track backward.

Note: If there is no audio streaming for 20 minutes, Bluetooth® mode turns off automatically.

Changing Audio Output

1. Press the SPEAKERS ON/OFF BUTTON to turn headphone speakers off and Cat Ear speakers on.
2. Press the SPEAKERS ON/OFF BUTTON again to turn headphone speakers on (Cat Ear speakers remain on).
3. Press the SPEAKERS ON/OFF BUTTON again to turn headphone speakers on and Cat Ear speakers off.

Incoming Calls

1. To answer an incoming call, press the PLAY/PAUSE/TRACK FORWARD/TRACK BACK BUTTON once.
2. To ignore an incoming call, press and hold the PLAY/PAUSE/TRACK FORWARD/TRACK BACK BUTTON until a tone sounds, then release.
3. To end an active call, press the PLAY/PAUSE/TRACK FORWARD/TRACK BACK BUTTON once.

Selecting Light Colors

Press the LIGHTS ON/OFF/CHOOSE COLOR BUTTON to control the ear cup and speaker lights. The default color is Blue.

1. Press to change lights to Green.
2. Press to change lights to Purple.
3. Press to change lights to Orange.
4. Press to change lights to White.
5. Press to change lights to Red.
6. Press to change lights to Yellow.
7. Press to change lights to Pink.
8. Press to change lights to Blue.
9. Press and hold to turn the ear cups and speaker lights off.

Selecting Light Modes

1. Press the LIGHT MODE BUTTON to activate Breathing mode (slow flashing of selected color).
2. Press the LIGHT MODE BUTTON to activate Transition mode (color transitions every 5 seconds).
3. Press the LIGHT MODE BUTTON to activate Beat mode (color beats to audio).
4. Press the LIGHT MODE BUTTON to activate Strobe mode (fast flashing of selected color).
5. Press the LIGHT MODE BUTTON to activate Solid mode (selected color is solid).

Note: If no beat is detected (low volume or insufficient bass), Beat mode defaults to Solid mode.

Using the Headphone Cord

Connect your device to the headphones using the included 3.5mm to 3.5mm headphone cord.

1. Plug the end of the headphone cord with two rings into the HEADPHONE CORD INPUT on the headphones.
2. Plug the end of the headphone cord with three rings into your audio device.

Diagrams illustrate the two-ring connector for headphones and the three-ring connector for audio devices.

Use your device to control volume through the headphones.

1. Press the PLAY/PAUSE/TRACK FORWARD/TRACK BACK BUTTON on the headphone cord once to play or pause audio.
2. Press twice in quick succession to move one track forward.
3. Press three times in quick succession to move one track backward.
4. To answer an incoming call, press the button once.
5. To ignore an incoming call, press and hold the button for 2 seconds, then release.
6. To end an active call, press the button once.

Notes:

• The HEADPHONE CORD INPUT takes precedence over the Bluetooth® connection.
• If there is no audio streaming for 20 minutes, the Cat Ear Speakers turn off automatically.

Compatibility

Requires a Bluetooth 2.1 or above device with A2DP and AVRCP profiles.

Care and Maintenance

Unplug the headphones and spot clean with a soft, dry cloth.

Frequently Asked Questions

Why won't audio play?

• Ensure your device is within 33 feet of headphones and reconnect your device. Refer to page 9 for pairing instructions.
• Check the headphones' or your device's volume level.
• Charge the headphones (if using Aux in, headphones must be charged).

Why isn't the audio clear?

• Ensure your device is within 33 feet of the headphones.
• Reconnect your device to headphones. Refer to page 9 for pairing instructions.
• Check the headphones' or your device's volume level.
• Adjust your device's equalizer.
• Charge the headphones (if using Aux in, headphones must be charged).

How do I pair a new device?

The headphones remember the last device paired. To pair a new device, do so manually. Refer to page 9 for pairing instructions. You may need to turn Bluetooth® off on the last paired device to prevent automatic re-pairing.

Why won't the lights stay on?

• Charge the headphones. If the battery is depleted, it may take several minutes after plugging in the MICRO USB CHARGING CABLE for enough battery life to keep the lights on.
• The ear cups and speaker lights turn off if pairing mode is cancelled automatically. Press the LIGHTS ON/OFF/CHOOSE COLOR BUTTON to turn them on.

Why can't I play/pause, change tracks, or answer calls with the button on the headphone cord?

• Ensure the end of the HEADPHONE CORD with two rings is plugged into the HEADPHONE CORD INPUT on the headphones.
• Ensure the end of the HEADPHONE CORD with three rings is plugged into your audio device.

Diagrams illustrate the two-ring connector for headphones and the three-ring connector for audio devices.

Specifications

The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by Brookstone are under license.

One (1) Year Limited Warranty

Brookstone® warrants this product against defects in materials and/or workmanship under normal use for a period of ONE (1) YEAR from the date of purchase by the original purchaser (“Warranty Period”). If a defect arises and a valid claim is received within the Warranty Period, at its option, Brookstone will either 1) repair the defect at no charge, using new or refurbished replacement parts, or 2) replace the product with a new product that is at least functionally equivalent to the original product, or 3) provide a store credit in the amount of the purchase price of the original product.

A replacement product or part assumes the remaining warranty of the original product. When a product or part is exchanged, any replacement item becomes your property and the replaced item becomes Brookstone's property. When a store credit is given, the original product must be returned to Brookstone and becomes Brookstone's property.

Obtaining Service:

To obtain warranty service, call Brookstone Limited Warranty Service at 1-800-292-9819. Please be prepared to describe the product and the nature of the problem. A purchase receipt is required. All repairs and replacements must be authorized in advance. Service options, parts availability, and response times will vary. You are responsible for delivery and the cost of delivery of the product or any parts to the authorized service center for replacement, per instructions.

Limits and Exclusions:

Coverage is limited to the United States of America, including its territories. This Limited Warranty applies only to products manufactured for Brookstone identified by the “Brookstone” trademark, trade name, or logo. It does not apply to non-Brookstone products. Manufacturers or suppliers other than Brookstone may provide their own warranties.

This warranty does not apply to:

• Damage caused by failure to follow instructions relating to product use or installation.
• Damage caused by accident, abuse, misuse, fire, floods, earthquake, or other external causes.
• Damage caused by service performed by anyone who is not a Brookstone representative.
• Accessories used in conjunction with the product.
• Products or parts modified to alter functionality or capability.
• Items intended for periodic replacement (e.g., batteries, light bulbs).
• Products sold "as is" (e.g., floor demonstration models, refurbished items).
• Products used commercially or for a commercial purpose.

BROOKSTONE SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. TO THE EXTENT PERMITTED BY APPLICABLE LAW, BROOKSTONE DISCLAIMS ANY AND ALL STATUTORY OR IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS. IF BROOKSTONE CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED WARRANTIES, THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES SHALL BE LIMITED IN DURATION TO THE DURATION OF THIS EXPRESS WARRANTY.

Some states disallow the exclusion or limitation of incidental or consequential damages or how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state.