ASSEMBLY INSTRUCTIONS

WARNING

Tip-Over Hazard

Children have died from furniture tip over. To reduce the risk of tip over:

• ALWAYS secure this furniture to the wall using an anti-tip device. ✔️
• NEVER allow children to stand, climb, or hang on drawers, doors or shelves. ❌
• Do not defeat or remove the drawer interlock system. ❌
• Place heaviest items in the lowest drawers. ✔️
• NEVER put a TV on this furniture. ❌

To ensure the safety of those using this cabinet, it is crucial to properly secure it to the wall using a tip-over device. This product includes the necessary items for fixing the furniture to the wall. However, it is important to note that incorrect installation or failure to use the tip-over device can result in serious injury or even death. For this reason, we highly recommend that a professional installer handle the installation of the cabinet to the wall.

Index

• What will you need? (Page 2)
• Where should you start? (Page 3)
• What's in the hardware bag? (Pages 4-5)
• How do the dowels and Minifix system work? (Page 6)
• Let's start assembling! (Page 7)
• How much weight does your cabinet resist? (Page 23)
• Our last recommendations for taking care of your cabinet (Page 24)

What will you need?

Hi! my name is Armando, and I'll be with you while you assemble this cabinet.

Tools required:

• Phillips head screwdriver
• Flat head screwdriver
• Hammer

Assembly surface:

• A flat, smooth surface. You can use the cardboard of the box or a rug.

An electric screwdriver isn't necessary, but it can make the work much easier :)

Where should you start?

Important Check

Over the next few pages is the panel and hardware content for this cabinet. Please make sure that the quantity of each one is correct, and that everything is in good shape. (When the cabinet is already assembled there's no warranty for this)

Panel Quantity

What's in the hardware bag?

Hardware Components:

• Wood dowel x61
• Spreading bolt x38
• Minifix cam x38
• Cover caps x40
• Wall anchor + screw x2
• Rear panel Clamp x10
• Flat head screw x18
• Drywall screw x18
• Hinge + screws x8
• Plastic leg x6
• Handle + screws x6
• Drawer slides + screws x2
• Closet rod x3
• Closet rod support x6
• Nail x72
• H profile x3
• Hinge + screw x4

Be careful!, try not to lose anything from this bag, its content is necessary for assembling your cabinet.

How do the dowels and Minifix system work?

Everytime you're using one of these connectors during the assembly, you should follow these same steps.

Wood dowels

They are little wooden cylinders.

1. Step 1: Insert the dowel inside the indicated hole and softly hit it until it's fully inside.
2. Step 2: When joining two panels together, don't forget to gently hit the panels to adjust the joint.

Minifix system

It's a joint compound of two parts: a spreading bolt and a Minifix cam.

1. Step 1: Identify the Minifix cam (it has a little arrow on its upper surface).
2. Step 2: Insert these cams with the little arrow pointing towards the drilling on the panel's edge.
3. Step 3: Insert the spreading bolt with the black plastic part facing down.
4. Step 4: After joining two panels together, turn the cams 180° with a Phillips head screwdriver to adjust and secure the joint.

Assembly Steps

Detailed steps for assembling the wardrobe:

1. Step 1: Attach panel O to another panel using dowels and screws.
2. Step 2: Attach panel I with multiple screws and dowels.
3. Step 3: Attach panel H (x2) to panel I using screws.
4. Step 4: Attach panels D and E, potentially with drawer slides and hinges. Note the 'Rotate' instruction.
5. Step 5: Install drawer slides onto panels D and E, then attach panels O, H (x2), and I to the base. Ensure hinges are closed before installing parts.
6. Step 6: Attach drawer slides to panels F and G. Ensure hinges are closed before installing parts.
7. Step 7: Assemble the main frame by joining panels F, G, O, H (x2), D, E, I.
8. Step 8: Attach panel M (x2) with a bolt.
9. Step 9: Attach panel J with screws and dowels.
10. Step 10: Attach panel L (x2) with screws and dowels.
11. Step 11: Attach hinges and other hardware to panel C. Note the 'Rotate' instruction. Ensure hinges are closed before installing parts.
12. Step 12: Assemble the main structure by joining panels C, J, M, H, E, D, G, I. Ensure hinges are closed before installing parts.
13. Step 13: Attach hinges and hardware to panel B. Ensure hinges are closed before installing parts.
14. Step 14: Assemble the main structure by joining panels B, B, J, C, L, M, H, G, E, D, I. Ensure hinges are closed before installing parts.
15. Step 15: Attach hardware to panel A.
16. Step 16: Assemble the main structure by joining panels B, A, J, C, L, M, H, G, E, D, I. Use drywall screws.
17. Step 17: Attach plastic legs to panel K using flat head screws. Note the 'Rotate' instruction.
18. Step 18: Assemble the main structure by joining panels A, L, H, B, G, J, E, I, C, K.
19. Step 19: Attach back panels using nails (U). Use 164.5 cm and 172.6 cm profiles to join center pieces. The diagram shows nail placement and a 3mm measurement.

Fix your cabinet to the wall

Follow these steps to securely attach the wardrobe to the wall:

1. On the wall, measure and mark the points shown below. [measuring tape]
2. Drill on the markings with a 5/16" drill bit. [drill]
3. Insert the wall anchors inside the drillings. [wall anchor]
4. Place the cabinet and secure it with the screws. [screw]

The diagram shows the cabinet's dimensions for wall mounting: total height 171.4 cm (57.48 inches), with specific horizontal measurements for placement points (25.8 cm / 10.15 inches from edges, 98.6 cm / 38.8 inches in the center). Vertical measurements are 6.5 cm / 2.5 inches from the top.

Drawer Assembly

Steps for assembling the drawers:

1. Step 21: Attach hardware to panels P (x2) and Q (x2).
2. Step 22: Assemble drawers using panels P, Q, and R, securing with drywall screws.
3. Step 23: Attach hardware to panels FC (x2).
4. Step 24: Slide back panels (FC) into the grooves of drawer parts P, R, and N.
5. Step 25: Drawer Installation: The wheel should go on the rear part of the drawer. Attach drawer front (FC) and sides (P, N) to the drawer box.
6. Step 26: Insert the assembled drawers into the cabinet. Ensure to locate the tubes inside the cabinet.

Door Installation

Steps for installing the doors:

1. Step 27: Attach doors with hinges (PI) to the cabinet body.

Hinge adjustment

Adjustments can be made for:

• Depth adjustment
• Lateral adjustment
• Height adjustment
• Front screws adjustment

After adjusting all the Minifix cams, cover them up with the cover caps. [cover caps]

After finishing the assembly, lift off all the adhesive letters. [adhesive letters]

How much weight does my cabinet resist?

The cabinet can support the following approximate weights in pounds:

The diagram indicates that shelves or compartments can hold approximately 22 lbs or 33 lbs.

Congratulations! It's done. But don't go yet! There are some recommendations left for you to take care of your cabinet correctly from now on.

SUPER IMPORTANT!

We suggest fixing the cabinet to the wall, so we can avoid the cabinet tipping and harming anyone. Be specially careful with the kids.

Taking care of your cabinet:

• Do not paint the cabinet.
• The cabinet is exclusively for indoor spaces. Do not expose it to the direct sun.
• Clean the metallic hardware with a dry cloth.
• DO NOT overload the cabinet (see suggested loads).
• Do not hit or hammer the cabinet (only when indicated here).
• Clean it with thinner, a soft soap solution or simply a damp cloth.
• Don't drag the cabinet, lift it up with other people.
• Avoid direct contact with water, fire or exposing it to high heat.

Cabinet panels

The exploded view shows all the cabinet panels labeled with letters A through U, PD, PI, and FC.

WARRANTY POLICY

Furniture has a 1 year warranty coverage in wooden parts and hardware pieces since its manufacturing date, which you can see in the lot number printed on the product box and the assembly instructions leaflet.

Warranty covers materials and workmanship imperfections which impair the assembly or correct functioning of the cabinet.

This warranty is not valid if the defects or imperfections are caused by the incorrect following of the assembly instructions, warnings and recommendations, misuse, intentional damage, fire or flood, or after modifications or any kind of alteration, or repaired by someone not authorized, when it's been assembled 3 months after the date of purchase. These defects MUST be reported before the warranty coverage period ends.

Once the product has been assembled, the company will not be responsible for defective and/or damaged parts.

This warranty is ONLY valid for the ORIGINAL PURCHASER, it doesn't apply if the product has been resold, rented, etc.

Furniture will take no liability for incidental or consequential damages caused to or by the product (This may not apply in your state).

To make this warranty valid you must write to our customer service email describing the product defect, lot number and submitting your sales receipt or proof of purchase, or contact us at our customer service line. Replaced parts will be under the product's original warranty coverage period. Damaged parts will become property of the company.

There are no other warranties applicable to this product.