Contents
- Assembling your machine
- Getting started
- Power and continuous monitoring
- Information menu
- Auto mode
- Airflow speed and direction
- Oscillation
- Night mode
- Sleep timer
- Heating and Cooling modes
- Changing your HEPA+Carbon filter
- Resetting your HEPA+Carbon filter life
- Changing your HEPA and carbon filters
- Resetting your HEPA and carbon filter life
- Looking after your machine
Assembling your machine
Use both hands to lift your machine out of the box, by its base. Do not lift by the loop amplifier. Assemble your machine with the supplied filters.
Dyson Pure Hot+Cool (Supplied with a HEPA+Carbon filter)
Push your HEPA+Carbon filter into the outer cover and position onto the base. Push firmly until both outer covers click securely into place.
Diagram Description: The air purifier fan heater with filter covers open, showing a HEPA plus carbon filter located in the filter covers. Arrows indicate that the filter covers will need to be assembled onto the base of the machine.
Dyson Pure Hot+Cool (Supplied with separate HEPA and carbon filters)
Push the carbon filters into place on the machine. Push the HEPA filter into the outer cover. Put the outer covers into position on the base and push firmly until they both click securely into place.
Diagram Description: The air purifier fan heater with filter covers open, showing a HEPA filter in the filter covers and a carbon filter. Arrows indicate that the carbon filter is fitted directly to the base of the machine and the filter covers will need to be assembled onto the base of the machine.
Getting started
Place the remote control on top of the machine with the buttons facing down. Plug in and switch on.
Diagram Description: Image of the air purifier fan heater with the remote placed on top of the loop amplifier, showing the location of the standby on/off button on the top of the base.
Remote Control Layout
The remote control features the following buttons:
- Top Left: [Standby on/off button]
- Left Side: [Airflow speed toggle button], below it [Auto mode button], below it [Oscillation on/off button], at the bottom [Sleep timer button].
- Top Right: [Information menu button]
- Right Side (downwards): [Heating control button], below it [Cooling mode button], below it [Airflow direction button], at the bottom [Night mode button].
Power and continuous monitoring
Stand-by on/off
Press the [Standby on/off button] on your Dyson purifying fan heater or remote control to stop your machine. It will continue to monitor the air quality.
Continuous monitoring
Continuous monitoring is turned off by default. Once turned on, it will always be active until you turn it off again.
With continuous monitoring turned on, your Dyson purifying fan heater will gather air quality, temperature, and humidity information, which is displayed on the LCD screen.
To turn continuous monitoring on or off, press and hold the [Auto mode button] on the remote control for 5 seconds. The LCD screen will indicate when continuous monitoring is on or off.
Auto mode
Set your Dyson purifying fan heater to Auto mode and the on-board sensors will intelligently adjust the settings of the machine according to the air quality. Air quality: your machine will pause when the target air quality has been reached, switching on again when the air quality levels drop. Airflow speed: the airflow speed will increase until the target air quality and temperature have been reached.
Diagram Description: Remote control with the [Auto mode button] highlighted below the [Airflow speed button] on the left.
Airflow speed and direction
Press the [Airflow speed button] to increase and decrease the airflow speed. Press the [Airflow direction button] to change the direction of airflow from front to back. Change the airflow direction for your personal comfort. Select the Airflow direction to Fan mode for airflow from the front for purifying, cooling, and heating.
Diagram Description: Remote control with the [Airflow speed toggle button] on the left hand side, below the standby button. The [Airflow direction button] is on the right, above the [Night mode button].
Oscillation
Press the [Oscillation button] to circulate the air around the room and scroll through the oscillation settings from 0° to 350°.
Diagram Description: Remote control with the [Oscillation button] highlighted on the left, above the [Sleep timer button].
Night mode
In Night mode, your Dyson purifying fan heater will continue to monitor and respond to changes in air quality, but only using its quietest settings, and with its LCD screen dimmed.
Diagram Description: Remote control with the [Night mode button] highlighted on the right at the bottom.
Sleep timer
Your Dyson purifying fan heater will turn off automatically after the selected amount of time.
To set the time: press the button to scroll through the time options. Once activated, press the [Sleep timer button] once to see the time selected.
To cancel the Sleep timer: press the [Sleep timer button] twice.
Diagram Description: Remote control with the [Sleep timer button] highlighted on the bottom left.
Heating and Cooling modes
Press the [Heating control button] to set the required room temperature. Your machine will pause when the temperature set has been reached.
Press the [Cooling mode button] to switch your machine from heating mode to cooling mode.
Diagram Description: Remote control with the [Heating mode button] on the right, below the [Information button]. The [Cooling mode button] is immediately below the [Heating mode button].
Changing your HEPA+Carbon filter
Before changing your filter, switch off and unplug your Dyson purifier fan heater. The remaining filter life is displayed on the screen and will indicate when your non-washable filters need replacing. Press the [Information button] on your remote. You'll need to reset the filter life on your machine.
Dyson Pure Hot+Cool (Supplied with a HEPA+Carbon filter)
To change your HEPA+Carbon filter, push down on the buttons either side of your machine to release the outer cover. Push down on the tabs to remove the filter. Push the replacement filter into the outer cover and make sure the tabs click into place. Put the outer covers into position on your machine and push firmly until they both click securely into position. Plug in and switch your machine, and reset your filter life.
Diagram Description: The air purifier fan heater with the filter covers open showing a HEPA plus carbon filter located in the filter covers. Arrows demonstrate that the filter covers will need to be assembled onto the base of the machine.
Resetting your HEPA+Carbon filter life
It's important to reset your filter life after you have replaced your filter.
Press and hold the [Night mode button] on your remote control for 5 seconds. The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.
Diagram Description: Remote control with the [Night mode button] highlighted on the bottom right for 5 seconds.
Changing your HEPA and carbon filters
Before changing your filter, switch off and unplug your Dyson purifier fan heater. The remaining filter life is displayed on the screen and will indicate when your non-washable filters need replacing. Press the [Information button] on your remote. You'll need to reset the filter life on your machine.
Dyson Purifier Hot+Cool Auto React (Supplied with separate HEPA and carbon filters)
To change your HEPA filter, push down on the buttons either side of your machine to release the filter covers. Push down on the tabs to remove the HEPA filter. Push the replacement filter into the outer cover and make sure the tabs click into place. To change the carbon filter from your machine, remove the filter from the base of your machine and insert the replacement filter. Put the outer covers into position on your machine and push firmly until they both click securely into position. Plug in and switch your machine, and reset your filter life.
Diagram Description: The air purifier fan heater with the filter covers open showing a HEPA filter located in the filter covers and a carbon filter. Arrows demonstrate that the carbon filter is fitted directly to the base of the machine and the filter covers will need to be assembled onto the base of the machine.
Resetting your HEPA and carbon filter life
It's important to reset your filter life after you have replaced your filter.
Resetting your HEPA filter life
Press and hold the [Night mode button] on your remote control for 5 seconds. The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.
Diagram Description: Remote control with the [Night mode button] highlighted on the bottom right for 5 seconds.
Resetting your carbon filter life
Press and hold the [Oscillation button] on your remote control for 5 seconds. The display on your machine will countdown from five, the filter life will be reset and your machine is ready to use.
Diagram Description: Remote control with the [Oscillation button] highlighted on the bottom left, above the [Sleep timer button], for 5 seconds.
Looking after your machine
Cleaning your machine
To always get the best performance from your Dyson purifying fan heater, it's important to regularly clean it and check for blockages. If your machine is dusty, wipe with a damp lint-free cloth. Look for blockages in the air inlet holes on the filter and the small aperture inside the loop amplifier. Use a soft brush to remove dust and debris. Do not use detergents or polishes to clean your machine.
Error codes
If your machine shows an error code, try turning it off and then on again. If this doesn't clear the error code, contact Dyson Customer Care.
For more information and support for your machine, go online: www.dyson.com/support
