C2C36 INSTALL GUIDE
DIMENSIONAL RENDERINGS
Detailed diagrams illustrating the overall product dimensions and cutout dimensions for island installations. These renderings provide precise measurements for integrating the Coyote C2C36 grill into various outdoor kitchen setups.
Overall Product Dimensions
| Model No. | Height | Width | Depth |
|---|---|---|---|
| C2C36 | 23" | 35 1/2" | 25 1/2" |
| CJAKTCS36 | 11" | 37 5/8" | 23" |
Cutout Dimensions for Island
| Model No. | Height | Width | Depth |
|---|---|---|---|
| C2C36 | 10 1/4" | 32 1/2" | 20 1/2" |
| CJAKTCS36 | 11" | 35 3/4" | 22 1/8" |
Note: When using a Coyote insulated jacket, ensure your island is built to the jacket's cutout and overall dimensions. The grill will rest on or inside the insulated jacket once installed.
Specifications and Electrical Requirements
| Model No. | Gas Supply | BTU's | Regulator | WC Pressure | Max PSI | Electrical Requirements |
|---|---|---|---|---|---|---|
| C2C36LP | Propane | 80,000 | 20 lb Tank Regulator | 11" WC | .5 PSI | Qty 1 - 120 VAC 60 Hz Grounded Plug |
| C2C36NG | Natural Gas | 80,000 | 1/2" Female Pipe | 4" WC | .5 PSI | Qty 1 - 120 VAC 60 Hz Grounded Plug |
Important Note to Installer: This document is not a substitute for the Owner's Manual, which contains critical safety information and consumer guidelines. Always refer to the Owner's Manual before installation or operation.
INSTALLATION REQUIREMENTS
NON-COMBUSTIBLE CONSTRUCTION (Insulated Jacket NOT Required)
Diagrams show top and front views for non-combustible construction, detailing clearances and gas connection points. Key considerations include:
- Maintain a minimum 24" clearance from the grill frame to combustible materials (horizontal and vertical).
- The shaded area in the top view indicates the 24" minimum requirement (not to scale).
- The grill is designed to hang from the countertop without underneath support.
- Minimum 2" rear clearance is required for the hood to open.
- A minimum 7" rear clearance to a wall or partition is recommended for exhaust ventilation.
COMBUSTIBLE CONSTRUCTION (Insulated Jacket Required - Model # CJAKTCS36)
Diagrams show top and front views for combustible construction, highlighting the necessity of the insulated jacket and clearances. Key considerations include:
- If combustible materials are within 24" of the grill frame, the Coyote Insulated Jacket (Model # CJAKTCS36) must be used.
- Using the insulated jacket does not negate other standard installation procedures, such as ventilation and connections.
- The jacket is designed to hang from the countertop without underneath support.
- Minimum 2" clearance for the hood to open.
- A minimum 7" rear clearance to a wall or partition is recommended for exhaust ventilation.
Ventilation Requirements (Applicable to both construction types)
Proper ventilation is crucial for safe operation. Ensure the following:
- Install at least two vents within the island, each with a minimum area of 20 sq. inches.
- These vents must allow fresh air to circulate from the grill cabinet to the exterior.
- For propane grills, install vents lower in the island as propane is heavier than air.
- For natural gas grills, install vents higher in the island as natural gas is lighter than air.
- Position the two vents on different walls of the island to facilitate cross-ventilation, which helps dissipate excess heat or trapped gas.
Important Note to Installer: This document is not a substitute for the Owner's Manual, which contains critical safety information and consumer guidelines. Always refer to the Owner's Manual before installation or operation.
