Manuals+

ACON AIR 13 HD Trampoline

Assembly Instructions & Product Specification

Introduction

This is an assembly instruction manual for the Acon AIR 13HD Trampoline. Ensure that you have read and understood the trampoline user manual before assembling this product. The owner and/or supervisor of the trampoline are responsible for making all users aware of the practices and information specified in the trampoline user manual. ACON Trampoline E-Manuals & more can be downloaded by scanning the QR-code or from: www.acon-manuals.com/trampoline-manuals

Parts List

This is a parts list for your trampoline. If any of the parts are missing, please contact ACON customer support.

TRAMPOLINE PARTS

ENCLOSURE PARTS

OTHER & TOOLS

Assembly Steps

Step 1: Assemble Trampoline Ends

Assemble trampoline ends. Tube #6: the side with more spring holes must be faced up. NOTE: lock nut is supposed to stop after a few twists while hand tightening.

Step 2: Connect Top Frame Tubes

Connect the trampoline ends with top frame tubes (#6). Tube #6: the side with more spring holes must be faced up. NOTE: lock nut is supposed to stop after a few twists while hand tightening.

Step 3: Assemble Mid Legs

Assemble mid legs.

Tips to install steel plates (#3):

  1. Make sure that the orientation of steel plate (#3) is correct—see the direction of the bends in the ends (turned away from the bottom of the leg assembly).
  2. Install one outer bolt first, and only barely hand tighten the nut. Then, install the outer bolt in the opposite end—it may help if you bow the steel plate slightly to better align the bolt holes. Also squeezing / bending the mid leg assembly by pulling / pushing in the directions shown in the figure below may help. One way to do that is to turn the leg assembly upside down against the ground (on a soft surface) and press down from the center. Hand tighten only.
  3. Proceed to install the inner bolts.

Step 4: Insert Mid Leg Assemblies

Insert the mid leg assemblies into the top frame as instructed below. Please note that the sides of the frame won't be straight at this point. They are pulled into their final positions after the springs are installed.

Step 5: Attach Enclosure Poles

CAUTION! INCORRECTLY INSTALLED PART CAN CAUSE INJURY! Please see the figure below on instructions to align the spacer between the enclosure pole and trampoline leg (arrows up and facing the enclosure pole). DO NOT USE POWER TOOLS.

Step 6: Tighten Bolts and Add Caps

TIGHTEN all the bolts that have been hand tightened in the previous steps. Add the plastic protective caps. DO NOT USE POWER TOOLS.

Step 7: Connect Springs

Connect springs (#10) to the v-rings of the mat (#9) and pull towards yourself with the spring pull tool to connect to frame. NOTE: Skirt of the mat must be above the springs (not displayed in figures below for clarity).

CAUTION! PINCH PONT. Pay attention to hand position when handling springs.

Choose spring setup between two options:

Step 8: Continue Spring Installation

Continue the spring installation by adding 1 spring in each gap, working clockwise around the trampoline until all the springs have been installed.

CAUTION! PINCH PONT. Pay attention to hand position when handling springs.

Step 9: Attach Mat Skirt

Attach the corners of the jumping mat skirt to the corners of the trampoline frame with elastic strips (#33).

Step 10: Attach Safety Pads

Attach safety pads (#11 and #12) to the frame with bungee cords (#13). Tip: using spring pull tool is helpful. If necessary, loosen the upper bolt of the enclosure pole slightly when placing the skirt of the safety pad between the enclosure pole and frame. REMEMBER TO RE-TIGHTEN.

Step 11: Assemble Enclosure Poles

Assemble all enclosure poles as instructed below. NOTE: Sliding the sleeve (#22) over the cap can be a tight fit. Connect the assembled poles in to the lower poles.

Step 12: Attach Net

Attach the short side of the net first. Adjust the lower edge of net to the centerline of safety pad as instructed in fig.1 with adjustable straps (part #26). The door opening can be placed on the short or the long side of the trampoline.

Step 13: Install Anchors

ENSURE THAT NO UNDERGROUND UTILITIES SUCH AS ELECTRICAL CABLES ARE PRESENT WHERE YOU INSTALL THE ANCHORS. Screw the anchors (#27) into the ground as instructed below. Fig. 2: Tie the strap of the anchor set over the upper frame of the trampoline. Attach the hook into the loop of the anchor base. Tighten with the ratchet.

Product Specifications

Product dimensions and ASTM / CE –certified weight limits:

WARNING! maximum user weight: 330 lb (150 kg)

Contact Us

EUROPE

Email: customercare.eu@acon24.com

Website: acon24.com

USA & CANADA

Email: customercare.us@acon24.com

Tel: +1 (866) 297 5234

Website: us.acon24.com

SWEDEN

Email: kundtjanst@acon24.se

Tel: +46 (08) 12013113

Website: www.acon24.se

FINLAND

Email: acon@acon.fi

Tel: +358 (0)9 42720823

Website: acon.fi

Models: AIR 13 HD Rectangular Trampoline with Net, AIR 13 HD, Rectangular Trampoline with Net, Trampoline with Net, Net

PDF preview unavailable. Download the PDF instead.

ACON-Air-13HD-Assembly-manual 1 ?v=1728325047 Microsoft Publisher for Microsoft 365

Related Documents

Preview Acon Airtracks User Manual: Setup, Use, and Care Instructions
Official user manual for ACON Airtracks, Airbeam, Airblock, Airspot, and Airroll products. Includes detailed instructions for setup, inflation, deflation, maintenance, and troubleshooting. Learn about recommended pressure (PSI), cleaning, storage, and contact information for ACON customer support.