Aiwa Essentials Audio Kit
Item: AI9006 - Quick Start Guide
What's Included
- Prodigy Move Wireless Speaker: A compact, portable speaker with a mesh grille and Aiwa branding.
- Prodigy Micro True Wireless Earphones with Charging Case: Compact earbuds accompanied by a charging case featuring an LED display.
- Silicone Eartips: Multiple sizes (S, M, L) for a comfortable fit.
- Over-Ear Wireless Headphones with Foldable Headband: Over-ear headphones with a foldable design and Aiwa branding.
- USB Charging Cable: One standard USB charging cable (labeled '1X').
- USB-C Charging Cable: One USB-C charging cable (labeled '2X').
- Quick Start Guide: This document.
Your Wireless Speaker
A Closer Look
The wireless speaker features several ports and controls:
- 1. USB reader
- 2. MicroSD card reader
- 3. LED Indicator
- 4. Charging port
- 5. Power On/Off switch
- 6. Mode change button
- 7. Volume - / Previous Track button
- 8. Microphone (Mic)
- 9. Volume + / Next Track button
- 10. Play / Pause / Call Controls button
The speaker has a front grille and a top/side control panel.
Charging
To charge the speaker, insert one end of the included USB charging cable into the speaker's charging port and the other end into a suitable USB charging adapter. The LED Charging Indicator Light turns red while charging and turns off when fully charged.
Powering On/Off
Set the power switch to the ON position to power on the speaker. Set the power switch to the OFF position to turn off the speaker. It is recommended that the speaker is fully charged before use.
Bluetooth Pairing
Once powered on, the speaker enters pairing mode, indicated by a flashing blue LED. On your smartphone, navigate to Bluetooth settings, ensure Bluetooth is turned on, and connect to the device listed as "AI9006 Speaker." After successful pairing, the speaker's LED indicator will turn solid blue.
Controls
Play/Pause Button: Press once to play or pause a track. Press to accept an incoming call and press again to hang up. Press and hold to reject an incoming call. Press twice to redial the last called number.
Volume + Button: Press to go to the next song. Press and hold to turn the volume up.
Volume - Button: Press to go to the previous song. Press and hold to turn the volume down.
Mode Button: Press to switch between Bluetooth, MicroSD Card Reader, USB Reader, and FM Radio modes.
Changing Modes
Press the mode button to cycle through available modes:
- Bluetooth mode: Allows pairing your speaker to a Bluetooth-enabled device.
- FM mode: Used to listen to available FM radio channels. Press the play/pause button to automatically search for stations. Use the '+' or '-' buttons to navigate stations. Press and hold '+' or '-' to control volume. If signal reception is poor, connect a charging cable to enhance it.
- USB mode: When a USB thumb drive is inserted into the USB port, the speaker will play .MP3, .WMA, or .WAV music files stored on the drive.
- MicroSD mode: Slide a Micro SD memory card into the Micro SD Card Slot. The speaker can play .mp3 music files from your card.
Your Wireless Earphones
A Closer Look
The wireless earphones and their charging case are detailed:
- Charging Case: Features a Charging Port (1), an LED Display Screen (2) showing battery status, a Left Earphone Icon (3), and a Right Earphone Icon (4).
- Earphones: Each earphone has an LED Indicator (6) and a Multifunction Button (7).
- The LED display screen also shows Battery Display (5) information.
Charging
Charging the Earphones: Place the earphones into the charging case to charge.
Charging the Case: Insert the included USB-C charging cable's USB-C end into the charging port on the case. Insert the other end into a USB port on a computer or a suitable wall adapter. Leave to charge.
Charging Status: The digits on the case's LED display screen will flash while charging and display a solid 'OK' when fully charged. The earphones flash RED while charging and turn OFF once charging is complete.
Powering On/Off
When first using your earphones, place them into the case. When you remove them from the case, they will automatically turn ON. When you place them back into the case, they will automatically turn off.
Note: If the earphones are out of the charging case, press and hold the multifunction button on both earphones for 3 seconds to power ON or OFF.
Bluetooth Pairing
When you remove your earphones from the case, they will power on and go into pairing mode. In pairing mode, one earphone will flash blue while the other will stop flashing.
On your smartphone, go to the Bluetooth settings menu. Make sure that Bluetooth is turned on. Connect to the device listed as "AI9006 Earbuds." Both earphones' LED Indicator will turn OFF once Bluetooth is connected.
After setting up Bluetooth, the earphones will automatically re-connect to the device every time you take them out of the charging case.
Controls
Left Earphone:
- Play/Pause: Press once
- Previous Track: Press and hold
- Volume +: Double Press
- Voice Assistant: Triple Press
- Answer Call: Press once (when incoming call)
- End Call: Press once
- Reject Call: Press and hold for 2 seconds
- Power ON/OFF: Press and hold for 3 seconds
Right Earphone:
- Play/Pause: Press once
- Next Track: Press and hold
- Volume -: Double Press
- Voice Assistant: Triple Press
- Answer Call: Press Once (when incoming call)
- End Call: Press once
- Reject Call: Press and hold for 2 seconds
- Power ON/OFF: Press and hold for 3 seconds
Note: Each earphone can be used alone while the other earphone is turned OFF as long as it is connected to Bluetooth.
Your Wireless Headphones
A Closer Look
The over-ear wireless headphones feature the following components:
- 1. Previous Track/Volume - button
- 2. Power On/Off/Play/Pause/Accept/End Call button
- 3. Next Track/Volume + button
- 4. Microphone (Mic)
- 5. Auxiliary Port
- 6. LED Indicator
- 7. Charging Port
- 8. MicroSD Card Reader
Charging
To charge the headphones, insert one end of the included USB-C charging cable into the charging port on your headphones. Insert the other end into a suitable USB charging adapter. The LED Charging Indicator Light turns red while the headphones are charging and will turn off when fully charged.
Powering On/Off
Press and hold the multifunction button for three seconds to turn ON/OFF the headphones. It is recommended that the headphones are fully charged before use.
Bluetooth Pairing
Once powered on, your headphones will go into pairing mode. The LED Indicator will flash red and blue alternately.
On your smartphone, go to the Bluetooth settings menu. Make sure that Bluetooth is turned on. Connect to the device listed as "AI9006 Headphone." After successful pairing, you will hear a voice prompt from the headphones.
Controls
Multifunction Button:
- Press to play or pause a track.
- Press to accept an incoming call and press again to hang up.
- Press and hold to reject an incoming call.
- Press twice to redial the last called number.
Volume + Button:
- Press to go to the next song.
- Press and hold to turn the volume up.
Volume - Button:
- Press to go to the previous song.
- Press and hold to turn the volume down.
MicroSD Card Mode: When inserting a MicroSD card into the MicroSD slot, the headphones will automatically enter card reader mode. In card reader mode, your speaker can play .mp3 music files from your card. Remove the MicroSD card to switch back to Bluetooth mode.
Specifications
Prodigy Move Wireless Speaker
- Speaker: 52mm
- Output: 4Ω 3W
- Bluetooth Version: 5.2
- Transmission distance: 10m
- Battery: 300mAh
- Charge time: 1-2H
- Play time: 1-2h
- Size: 120*45*70mm
Prodigy Micro True Wireless Earphones
- Driver Diameter: 8mm
- Frequency Response: 20-20kHz
- Impedance: 32ohm
- Bluetooth version: v5.3
- Transmission Distance: 10m
- Playtime: 3-4 Hours **
- Battery capacity (earphones): 30mAh
- Battery capacity (Case): 230mAh
- Charging input: DC 5V 1A (max)
- Charging type: Type-C
- **Applicable at 50% of maximum volume. Results will be lower when volume is higher.
Over-Ear Wireless Headphones
- Bluetooth version: v5.3
- Transmission Distance: 10m
- Playtime: 6 Hours **
- **Applicable at 50% of maximum volume. Results will be lower when volume is higher.
Safety Precautions
When using the devices from your audio kit, basic safety precautions should always be followed, including:
- READ ALL INSTRUCTIONS BEFORE USING YOUR DEVICES.
- Never expose your devices to high temperatures, extreme cold, high humidity, moisture, or water.
- To avoid the risk of electric shock, never attempt to open or repair your devices without the assistance of certified professionals.
- Your devices are not to be used by children or the infirm without suitable adult supervision.
- Always press all buttons carefully. Do not manhandle your devices.
- Do not use your devices at temperatures under 32°F (0°C) or over 104°F (40°C).
- Do not drop your devices, throw them, or subject them to strong impacts or physical trauma.
- Contact the manufacturer for support if you detect any abnormalities when using your devices. In addition, do not continue to use your devices if you detect any smoke or fire.
- Unplug your devices when not in use for extended periods of time.
- When plugged in, do not place your devices on flammable materials such as rugs, carpets, or bedding.
- Please recycle or dispose of your devices properly according to your municipality's laws and rules. Contact local recycling facilities and/or the manufacturer for further information.
- Clean your devices using a soft cloth or paper towel. Do not use harsh chemicals when cleaning your devices, and never submerge your devices in water.
BATTERY WARNING: ⚠️ The device is equipped with an integrated lithium ion battery. The battery cannot be replaced. Do not attempt to remove the battery from the device. Do not dispose of in fire or expose to excessive heat. Do not crush, puncture, incinerate, or short circuit external contacts. Please recycle or dispose of the battery properly. Contact your local recycling facilities and/or the manufacturer for further information.
Maintenance and Care
- Use a soft cloth or paper towel to clean your devices. Never use any harsh chemicals or detergents for cleaning. Make sure your devices are dry before charging.
- When your devices are unused, they should be stored in a cool, dry place.
- Never tug or yank on a cable connected to your devices. Connect and disconnect cables as carefully as possible.
- Never expose your devices to high temperatures or extreme cold.
FCC Statement
Speaker's FCC ID: 2AL9B-AI9006SPK
TWS's FCC ID: 2AL9B-AI1012
Headphone's FCC ID: 2AL9B-AI9006
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
This warranty covers the original consumer purchaser only and is not transferable.
This warranty covers products that fail to function properly UNDER NORMAL USAGE, due to defects in material or workmanship. Your product will be repaired or replaced at no charge for parts or labor for a period of one year.
What Is Not Covered By Warranty: Damages or malfunctions not resulting from defects in material or workmanship and damages or malfunctions from other than normal use, including, but not limited to, repair by unauthorized parties, tampering, modification or accident.
To Obtain Warranty Service and Troubleshooting Information: Call 1-800-592-9541 or visit our website at www.aiwa.co.
To receive Warranty service along with the name and address of an authorized product service center, the original consumer purchaser must contact Aiwa for problem determination and service procedures. Proof of purchase in the form of a bill of sale or receipted invoice, evidencing that the product is within the applicable Warranty period(s), MUST be presented in order to obtain the requested service. It is your responsibility to properly package and send any defective products along with a dated copy of proof of purchase, a written explanation of the problem, and a valid return address of the authorized service center at your expense. Do not include any other items or accessories with the defective product. Any products received by the authorized service center that are not covered by warranty will be returned unrepaired.
About Aiwa
AIWA
Edison, NJ 08817
© 2024 Aiwa Acquisitions LLC. All rights reserved. AIWA and associated marks are owned by Aiwa Acquisitions and used under license. Keep all relevant information for future reference.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and any use of such marks by Sakar International is under license.
AIWA | Legendary Speakers, Headphones, and Home Appliances
