SmallRig Wireless Follow Focus Kit (Lite) Operation Guide
Thank you for purchasing SmallRig's product. Please read this Operation Guide carefully. Please follow the safety warnings.
Product Installation and Power Supply Control
Wireless Receiver Motor Installation
Diagram illustrating the assembly of the wireless receiver motor, showing various components like gears, housing, and connection points, with arrows indicating the assembly sequence.
Wireless Receiver Motor Power Supply
The wireless receiver motor is powered by the included USB-C cable. It is compatible with PD + QC protocols, providing high torque output. The input voltage ranges from 5 V to 18 V.
Illustration showing a USB-C cable connected from a power source (e.g., power adapter, battery pack) to the USB-C port on the wireless receiver motor.
Wireless Handwheel Controller Operation
The input voltage of the wireless handwheel controller ranges from 5 V to 12 V. An external power adapter supplies power to the wireless handwheel controller via the included USB-C cable.
Image depicting the wireless handwheel controller, with a USB-C cable connecting it to an external power adapter.
Pairing and Synchronization
Ensure that the indicator of the wireless receiver motor is consistent with that of the wireless handwheel controller to guarantee control. Double-click the button to cycle through the frequency bands, F00-01 to F15-01.
Visual comparison of indicator lights on both the wireless receiver motor and the wireless handwheel controller, demonstrating how to match them for successful pairing.
[Note] The light color information corresponds to the frequency bands of the MagicFIZ wireless receiver motor and wireless handwheel controller.
Calibration
Automatic Lens Travel Calibration
Long press the CAL button for 2 seconds to start automatic lens travel calibration.
Close-up view of the device highlighting the 'CAL' button, with an arrow indicating a long press action.
Manual Lens Travel Calibration
Long press the CAL button for 2 seconds to start automatic lens travel calibration. Single-click the CAL button to switch to manual travel calibration.
Illustration of the 'CAL' button, showing a long press for automatic calibration and a single click for switching to manual calibration mode.
Marking Operation
Point A / B Marking Operation
Single-click the A / B mark (A-B-cancel) to mark the point.
Diagram showing the 'A/B' button, with labels indicating its function for setting start point (A), end point (B), and canceling the operation.
Troubleshooting
Abnormality of Wireless Handwheel Controller
The red light flashing indicates an alarm for low battery level or wireless receiver motor.
Visual showing a red indicator light flashing.
Description of Abnormal Alarm Case for Wireless Receiver Motor
Possible causes for motor abnormalities include:
- (1) The lens damping is too high, and the motor is stuck by a foreign object.
- (2) The motor input voltage is too low.
Operation to Address Abnormality of Wireless Receiver Motor
To address motor abnormalities:
- (1) Increase the input voltage or connect a device that supports PD+QC for power supply.
- (2) Use the included USB-C power cable or a USB3.0 power cable.
- (3) Single-click the CAL button on the wireless receiver motor or any button on the wireless handwheel controller to recalibrate the lens travel.
Abnormal Forward / Reverse Rotation of Wireless Receiver Motor
The wireless receiver motor shows abnormal reverse rotation.
Illustration of the wireless receiver motor with an arrow indicating its rotation direction, possibly highlighting an incorrect direction.
To resolve abnormal rotation:
- (1) Turn to the end position as shown in the figure.
- (2) Long press the button for 5 seconds until the current status light stops flashing to complete the reset operation.
Diagram showing the motor at its end position and highlighting the button to be pressed for reset.
Regulatory Information
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
- (1) This device may not cause harmful interference, and
- (2) This device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
ISED Statement
English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.
French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux CNR exempts de licence d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil.
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la conformité.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body.
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé.
